Contact Us

TPS40210DGQR

Brand: Texas Instruments
Texas Instruments TPS40210DGQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS40210DGQR — Power Management & Signal Chain | Superb Automation

TPS40210DGQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS40210DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS40210DGQR: 4.5 V to 52 V current mode boost controller

TPS40210DGQR is a nonsynchronous boost controller that drives an external N channel FET in a HVSSOP body of 10 pins. It is the control half of a boost, flyback or SEPIC stage, so the switch, the inductor and the diode stay outside the part.

Order code and package

Order codeTPS40210DGQR, DGQ package, 2500 pieces on a reel
BodyHVSSOP, 3.05 mm by 4.98 mm, ten pins with a heat slug
Reference700 mV, 693 mV to 707 mV at 25 C
Driver400 mA source and sink, ground referenced low side gate drive
FrequencyOne resistor and one capacitor on the RC pin, 35 kHz to 1 MHz

Electrical parameters that decide the application

Input range4.5 V to 52 V operating and absolute maximum
Undervoltage lockout4.30 V rising, 4.00 V falling, 300 mV of hysteresis
Overcurrent threshold150 mV typical at the ISNS pin, 120 mV to 180 mV over temperature
Current sense gain7.2 V/V from the ISNS pin to the control loop
Timing200 ns minimum on time and 200 ns minimum off time
Supply current1.5 mA typical and 2.5 mA maximum while switching, microamps when disabled
Bias regulator8 V at up to 15 mA, enough for the gate charge of a mid size FET
Soft start500 kOhm charge resistance, 150 mV reset threshold for the retry timer

Family variants and how they differ

TPS40211Same controller with a 260 mV reference, for a smaller current sense full scale
DGQ bodyHVSSOP with the heat slug, 67.2 C/W junction to ambient
RC pin at 182 kOhm and 330 pFSets the oscillator to 300 kHz typical
SS pinOne capacitor sets both the ramp and the retry period after an overcurrent
ISNS pinOne resistor to ground sets the trip point and also feeds the loop

Points to check before this part goes on a BOM

The part is a controller, so the loss budget lives outside it. A 12 V to 24 V boost at 2 A output has a duty cycle of 1 minus 12 over 24, which is 0.5, or 0.525 once the diode drop is counted. The external FET carries 2 A at 52 per cent of the time and the diode carries it for the rest, so a 20 mOhm FET and a 0.5 V Schottky are worth 0.04 W and 0.5 W respectively. The diode is the loss that matters, which is why a synchronous controller exists for higher currents.

The 150 mV current sense threshold is a fixed number, so the sense resistor is chosen from the peak current and nothing else. A 10 mOhm resistor trips at 15 A peak, which at a 1.5 A average and 40 per cent ripple is about 1.8 A of headroom. Going to 5 mOhm for efficiency doubles the trip point to 30 A, and the inductor has to be able to take that without saturating before the part protects anything.

Minimum on time of 200 ns limits the duty cycle at high frequency. At 1 MHz a 200 ns pulse is 20 per cent of the period, so a 5 V to 3 V conversion cannot run at 1 MHz on this part, and a 5 V to 12 V boost at 1 MHz needs 58 per cent duty with 420 ns on time, which is fine. The oscillator range of 35 kHz to 1 MHz is the boundary condition, not a target.

The soft start capacitor does two jobs. It sets the output ramp, and it sets the retry period after an overcurrent, because the SS pin is discharged to 150 mV and then recharged through 500 kOhm. A 1 uF capacitor gives a ramp of roughly 1.4 s from 8 V through 500 kOhm, and the same time constant governs how fast the converter tries again, so a short on the output produces a slow hiccup rather than a fast one.

The 700 mV reference is low enough that the feedback divider carries useful current at low output voltage. At 24 V out the divider can run 100 uA and still lose only 2.4 mW, and the 693 mV to 707 mV window is 2 per cent, which sets the DC accuracy of the rail unless the divider is trimmed.

The bias regulator stops at 15 mA, which is a gate charge budget. A FET with 30 nC of gate charge at 300 kHz needs 9 mA of average drive, so a larger FET at 500 kHz is over the limit, and the gate resistor has to be sized from that number rather than from switching speed alone.

The undervoltage lockout is fixed at 4.30 V, which matters for a 5 V input rail. A 5 V rail at minus ten per cent is 4.5 V and stays above the lockout, but a starter battery that sags to 4.2 V during crank will drop the controller out, and the DIS/EN pin is the only way to set a different threshold.

The ISNS pin is also the loop signal, so the sense resistor cannot be bypassed with a large capacitor without changing the loop. A 1 nF to 10 nF filter is the practical range, and anything above that adds a pole that the compensation network was not written for.

The leading edge blanking on the ISNS pin is what keeps the current limit from tripping on the turn on spike. The pin sees the gate charge of the FET plus the reverse recovery of the diode for the first tens of nanoseconds, and a limit that responded to that would fire on every cycle. A filter capacitor on the pin adds to the blanking time, which is why the sense resistor and the filter have to be chosen together.

In a flyback or SEPIC stage the same controller works, but the current sense moves to the primary or to the switch source and the voltage on the ISNS pin becomes a reflected output plus the leakage spike. That is why the 150 mV threshold is generous for a boost and tight for a flyback: the leakage inductance spike sits on top of the plateau and eats the margin unless the snubber is sized first.

Where this order code fits

The part suits a 12 V or 24 V industrial input that has to produce 36 V, 48 V or an LED string voltage, and any flyback or SEPIC stage that needs a grounded source switch. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it drive a P channel FET? No, the driver is ground referenced and meant for a low side N channel device. A P channel high side switch needs a different controller.

What limits the output current? The peak current through the sense resistor, set by the 150 mV threshold. The average output current follows from the duty cycle and the ripple.

Is there a synchronous version? Not in this family. The part drives one low side FET; a synchronous boost stage needs a second driver and a controller that supports it.

What happens on an overload? The ISNS pin crosses 150 mV, switching stops, the SS capacitor discharges and the converter restarts after the same charge cycle that sets soft start.

Can it be used for a SEPIC rail? Yes, the controller drives a grounded source FET, which is what a SEPIC needs. The sense resistor moves to the switch source and the coupling capacitor has to be rated for the full input voltage.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.