Contact Us

OPA551PA

Brand: Texas Instruments
Texas Instruments OPA551PA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA551PA — Power Management & Signal Chain | Superb Automation

OPA551PA

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA551PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA551PA: high-current high-voltage operational amplifier with 380 milliamps of output in an 8-pin plastic DIP

OPA551PA is a high-voltage operational amplifier that delivers 380 milliamps and runs from plus or minus 4 V to plus or minus 30 V with a thermal shutdown indicator in a PDIP body of 8 pins. The PA suffix is the 8-pin plastic DIP. The output stage sources and sinks 380 milliamps, the supply range is plus or minus 4 V to plus or minus 30 V, gain bandwidth is 3 MHz with 15 volts per microsecond on the OPA551 and 24 volts per microsecond on the OPA552, and offset is 1 millivolt typical and 3 millivolts maximum with 7 microvolts per degree of drift. A thermal shutdown flag is brought out so the system can see an overload before the output folds back.

Order code and package

Order codeOPA551PA
Functionhigh-current, high-voltage operational amplifier with thermal shutdown flag
PackagePDIP, 8 pins, body code P
Supply rangeplus or minus 4 V to plus or minus 30 V
Output current380 milliamps
Supply current7 milliamps typical, 8.5 milliamps maximum
Gain bandwidth3 MHz
Slew rate15 volts per microsecond on the OPA551, 24 on the OPA552
Offset1 millivolt typical, 3 millivolts maximum, 5 millivolts over temperature
Offset drift7 microvolts per degree
Input bias current20 picoamps typical, 100 picoamps maximum
DatasheetOPA551, OPA552 family document

Electrical parameters that decide the application

Common-mode rejection92 dB minimum, 102 dB typical over plus or minus 27.5 V
Open-loop gain110 dB minimum, 126 dB typical into 3 kilohms
Power-supply rejection10 microvolts per volt typical, 30 microvolts per volt maximum
Voltage noise14 nanovolts per root hertz at 1 kHz
Current noise3.5 femtoamps per root hertz at 1 kHz
Input common mode2.5 V inside either rail
Input capacitance2 picofarads differential, 6 picofarads common mode
Thermal flagopen drain style output that reports an overload before shutdown latches
Operating rangejunction minus 40 to plus 125 C

Points to check before this part goes on a BOM

380 milliamps into a plus or minus 30 V rail is 11.4 W of output, and the 8-pin DIP cannot dissipate that. At 8.5 milliamps of quiescent current the package is already at 510 milliwatts at plus or minus 30 V. The output stage dissipation is the sum of the drop across the output transistors, so a 30 V rail delivering 380 milliamps into a 10 ohm load dissipates 2.2 W in the package and needs a heatsink or a copper pour that the DIP leads can reach.

The thermal shutdown flag exists because the output stage can destroy itself before the load complains. The flag is an early warning at a lower junction temperature than the shutdown itself, so a controller can reduce the drive or report a fault before the amplifier folds back and the loop loses control. A board that ignores the flag still works, but it works until the first overload and then fails silently.

15 volts per microsecond at 40 V peak to peak gives a full power bandwidth of 60 kHz, and 3 MHz of gain bandwidth gives 300 kHz at a gain of 10. A 1 kHz sine at 40 V peak to peak needs 0.126 volts per microsecond, so the part is comfortable there; a 20 kHz signal at the same amplitude needs 2.5 volts per microsecond and is still inside the slew limit. Above 60 kHz the amplitude has to come down, and the OPA552 with 24 volts per microsecond extends that to 95 kHz.

The input stops 2.5 V inside either rail, which on a plus or minus 30 V supply leaves plus or minus 27.5 V of common mode. That is a wide window, and 92 dB of rejection over it means a 55 V common-mode shift contributes 1.4 millivolts at the input, comparable to the offset. In a high side current sense or a bridge driver running near the rail, the window is the first thing to check, because an input at 29 V on a 30 V supply is outside the specified range even though it is below the rail.

7 millivolts per degree of drift over 165 degrees is 1.16 millivolts, and the offset over temperature is specified at 5 millivolts. The drift is therefore a quarter of the guaranteed window, and the window widens mostly through the initial distribution rather than through drift. For a positioning loop that closes around the output, a 5 millivolt input error at a gain of 30 is 150 millivolts of output error, which is the number that decides whether the loop needs a trim.

14 nanovolts per root hertz at 1 kHz is a quiet amplifier for 380 milliamps of output, and it is what makes the part usable in an audio power stage where the same device is doing the voltage gain and the current gain. The 8-pin DIP's inductance and the decoupling are then the limit rather than the silicon, and the supply pins need local capacitance within a few millimetres because the output current flows through the same ground return as the input reference.

Where this order code fits

Valve and actuator drive, piezoelectric positioning, audio power stages, programmable power supplies and ATE force and voltage channels use this part because 380 milliamps into a 30 V rail covers a class of loads that a normal operational amplifier cannot touch without an external stage. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

How much power can the OPA551 dissipate in the DIP body? The quiescent dissipation alone is 510 milliwatts at plus or minus 30 V, and the output stage adds the drop across the output transistors. A high current load at a high rail needs a heatsink or a large copper area, and the thermal flag reports the junction before the shutdown latches.

What is the difference between the OPA551 and the OPA552? Slew rate and stability. The OPA551 is 15 volts per microsecond and unity gain stable, the OPA552 is 24 volts per microsecond and is specified for higher gains, so a fast low gain stage wants the first and a fast high gain stage the second.

Can the input work at the positive rail? No. The common mode stops 2.5 V inside either rail, so on a plus or minus 30 V supply the ceiling is plus 27.5 V even though the rail is higher.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.