Contact Us

OPA333AIDR

Brand: Texas Instruments
Texas Instruments OPA333AIDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA333AIDR — Power Management & Signal Chain | Superb Automation

OPA333AIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA333AIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA333AIDR: zero-drift CMOS operational amplifier with 10 microvolt offset and 17 microamps of supply current

OPA333AIDR is a zero-drift CMOS operational amplifier in an 8-pin SOIC that holds 10 microvolts of offset on 17 microamps from a 1.8 V supply in a SOIC body of 8 pins. The AIDR suffix is the 8-pin SOIC body supplied on a 2500 piece reel. The offset window is 2 microvolts typical and 10 microvolts maximum, drift is 0.02 microvolts per degree typical and 0.05 maximum, supply current is 17 microamps, and the input common mode reaches 100 millivolts beyond either rail, which is what makes a 1.8 V single supply usable for a ground referenced bridge.

Order code and package

Order codeOPA333AIDR
Functionzero-drift CMOS operational amplifier, rail-to-rail input and output
PackageSOIC, 8 pins, body code D, 2500 piece reel
Supply range1.8 V to 5.5 V
Supply current17 microamps
Gain bandwidth350 kHz with a 100 picofarad load
Slew rate0.16 volts per microsecond
Offset2 microvolts typical, 10 microvolts maximum
Drift0.02 microvolts per degree typical, 0.05 microvolts per degree maximum
Input common mode100 millivolts beyond either rail
Startupabout 100 microseconds to reach the specified offset after power up
DatasheetSBOS351E, revision of December 2015

Electrical parameters that decide the application

Power-supply rejection1 microvolt per volt typical, 5 microvolts per volt maximum
Common-mode rejection106 dB minimum, 130 dB typical
Input bias current70 picoamps typical, 200 picoamps maximum at 25 C, 150 picoamps typical over temperature
Input offset current140 picoamps typical, 400 picoamps maximum
Noise from 0.01 to 1 Hz0.3 microvolts peak to peak
Noise from 0.1 to 10 Hz1.1 microvolts peak to peak
Current noise100 femtoamps per root hertz at 10 Hz
Input capacitance2 picofarads differential, 4 picofarads common mode
Short-circuit current5 milliamps

Points to check before this part goes on a BOM

10 microvolts is 0.13 of a bit on a 16 bit converter at 5 V, so the amplifier stops being the accuracy limit entirely. Drift of 0.05 microvolts per degree over 165 degrees is 8 microvolts, still below the room temperature offset, so a channel calibrated once holds its reading to within a fraction of a bit over the whole industrial and automotive range. The remaining errors are the reference, the resistors and the thermocouples in the joints.

17 microamps at 3.3 V is 56 microwatts and 149 milliamp hours over a year, which is what makes a coin cell product possible. The same 17 microamps is also the reason the bandwidth is 350 kHz: the amplifier spends its current on the chopping loop and the calibration rather than on transconductance, so a 100 kHz signal at unity gain is already outside the small signal bandwidth.

The 0.3 microvolts peak to peak from 0.01 to 1 Hz is the figure that matters for a scale or a pressure sensor that updates once a second. At 16 bits on a 5 V range a bit is 76 microvolts, so the low frequency noise is four thousandths of a bit and the resolution is set by the sensor and the reference. Above 1 Hz the density curve rises to the 1.1 microvolts peak to peak quoted from 0.1 to 10 Hz.

The input goes 100 millivolts beyond both rails, which allows a bridge or a shunt to sit at the negative rail without a charge pump. It also means the input pair changes state as the common mode crosses between the two input stages, and the datasheet quantifies the resulting step rather than hiding it: the rejection falls to 80 dB in the crossover region against 130 dB typical outside it, so a signal that sits exactly at mid-rail sees a small nonlinearity.

Startup is a real specification: the part needs about 100 microseconds after power is applied before the offset meets the 10 microvolt window. A system that powers the amplifier, converts one reading 20 microseconds later and goes back to sleep will read the uncalibrated offset, and on a duty cycled node that is the difference between a working channel and an intermittent one. The 100 microseconds belongs in the wake up timing, not in the datasheet margin.

200 picoamps of maximum bias current through a 1 megohm source is 200 microvolts, which is twenty times the offset and therefore the dominant error on a high impedance sensor. At 10 kilohms the same current produces 2 microvolts, which is the offset itself. The practical source limit for this part is somewhere between those two, at about 100 kilohms where the bias error equals the offset window.

Where this order code fits

Coin cell and energy harvesting nodes, portable medical strips, gas and pressure sensors and precision low-side current sense stages use this part because 17 microamps and 10 microvolts rarely appear in the same order code. The 350 kHz bandwidth suits channels that convert a few thousand times a second. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Does the OPA333 need time to settle its offset after power up? Yes, about 100 microseconds before the offset meets the specified window. A duty cycled node has to allow for that delay before the first conversion.

How does the input behave at the supply rails? The common mode reaches 100 millivolts beyond either rail, but the input stage changes over inside that range and the common-mode rejection drops to 80 dB in the transition band against 130 dB typical outside it.

Is this part suitable for a 1.8 V single supply bridge? Yes. The supply floor is 1.8 V, the input goes 100 millivolts past both rails and the output is rail to rail, so a ground referenced bridge with a 1.8 V excitation is inside the specified window.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.