Contact Us

OPA316IDBVT

Brand: Texas Instruments
Texas Instruments OPA316IDBVT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA316IDBVT — Power Management & Signal Chain | Superb Automation

OPA316IDBVT

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA316IDBVT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA316IDBVT: 10 MHz low-power rail-to-rail operational amplifier in a 5-pin SOT-23 with 400 microamps per channel

OPA316IDBVT is a 10 MHz CMOS operational amplifier with rail-to-rail input and output, 400 microamps of supply current and an integrated radio frequency interference filter in a SOT-23 body of 5 pins. The IDBVT string unpacks into the industrial grade, the 5-pin SOT-23 body coded DBV, and a 250 piece tape. The amplifier runs from 1.8 V to 5.5 V, reaches 10 MHz of unity gain bandwidth with 6 volts per microsecond of slew, draws 400 microamps per channel typical, and holds input bias current to 15 picoamps maximum, which is what makes it usable with megohm source impedances on a low voltage rail.

Order code and package

Order codeOPA316IDBVT
Functionrail-to-rail input and output CMOS operational amplifier
PackageSOT-23, 5 pins, body code DBV, 250 piece tape
Supply range1.8 V to 5.5 V total
Supply current400 microamps per channel typical
Unity gain bandwidth10 MHz
Slew rate6 volts per microsecond
Input common mode0.2 V beyond either rail on supplies from 2.5 V to 5.5 V
Input bias current5 picoamps typical, 15 picoamps maximum
Output swingrail to rail, unity gain stable
Junction rangeminus 40 to plus 125 C
DatasheetSBOS703F, revision of October 2016

Electrical parameters that decide the application

Offset500 microvolts typical, 2.5 millivolts maximum, 3.5 millivolts over temperature
Offset drift2 microvolts per degree typical, 10 microvolts per degree maximum
Voltage noise11 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum and 86 dB typical at 1.8 V, 76 to 90 dB at 5.5 V
Power-supply rejection30 microvolts per volt typical, 150 microvolts per volt maximum
Channel separation10 microvolts per volt at DC
Input capacitance2 picofarads differential, 4 picofarads common mode
Interference rejectionintegrated input filter for radio frequency and electromagnetic interference
Shutdown optionthe OPA2316S dual adds a shutdown pin, this single does not

Points to check before this part goes on a BOM

2.5 millivolts of offset is two bits on a 12 bit converter at 5 V, and 3.5 millivolts over temperature is nearly three. That rules the part out as a DC precision stage but says nothing about its value as a dynamic one: at 10 MHz and 400 microamps the amplifier is aimed at signals that are measured over many samples rather than at a single DC transfer. A board that needs both wants a chopper on the DC path and this part after it.

Drift of 10 microvolts per degree is the widest in this family. Over the full 165 degree range it is 1.65 millivolts, which is two thirds of the room temperature offset, so an AC coupled stage is unaffected while a DC coupled one sees the offset grow by 66 percent over temperature. The 2 microvolt typical figure is the one most units deliver, but the guarantee is the 10.

15 picoamps of maximum bias current through a 1 megohm feedback resistor is 15 microvolts of error, which disappears behind the offset. That is the point of a CMOS input: at 10 megohms it is 150 microvolts and the amplifier is still usable, where a bipolar input at 40 nanoamps would produce 400 millivolts. Photodiode and pH electrode stages are the two places this matters.

The rail-to-rail input works 0.2 V beyond either rail, but the guarantee changes with supply. From 2.5 V to 5.5 V the input goes 0.2 V past both rails; on a supply from 1.8 V to 2.5 V the top of the window stops at the positive rail itself. On a 1.8 V board there is therefore no headroom above the rail, and a divider that sits 100 millivolts high is outside the window.

Audio and radio frequency interference at the input is handled by an on-chip filter rather than by external parts, which matters on a 5-pin footprint. The filter does not remove the need for a series resistor in a harsh environment but it does stop a 900 MHz handset from rectifying in the input stage, and the datasheet quantifies the rejection against frequency rather than promising a single number.

400 microamps per channel at 3.3 V is 1.32 milliwatts, so a quad in the same family is 1.6 milliamps, which is a tenth of what a 10 MHz bipolar amplifier would draw. The price is the offset and the drift, and the 11 nanovolts per root hertz noise is only moderate: over a 100 kHz band that is 3.5 microvolts RMS, close to three bits of a 12 bit converter at 3.3 V.

Where this order code fits

Portable medical front ends, electrochemical sensors, photodiode transimpedance stages and 3.3 V signal chains use this part because 10 MHz at 400 microamps is a rare combination and the picoamp bias current lets a 1 megohm feedback resistor work without a guard ring. The shutdown variant exists for duty cycled channels. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Does this part have a shutdown pin? No. The single OPA316 in SOT-23-5 does not, and the shutdown option belongs to the dual OPA2316S, so a duty cycled single channel needs an external switch or the dual part.

How does the input range change at 1.8 V? From 2.5 V to 5.5 V the input works 0.2 V beyond both rails. Between 1.8 V and 2.5 V the top of the window stops at the positive rail, so there is no over-the-rail headroom on a 1.8 V board.

Is 10 MHz usable at a gain of 100? Yes, at about 100 kHz of closed loop bandwidth, and the 6 volts per microsecond slew allows about 318 kHz on a 3 V peak to peak signal, so at a gain of 100 the gain limits before the slew rate does.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Choose an RF Amplifier page sets out the checks that keep a substitute from failing on the bench.