NE556DR
Product Specifications
NE556DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The NE556DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
NE556DR: dual precision timer in a 14-pin SOIC, two independent 555 blocks
NE556DR is two independent timers in one package, sharing only the supply rails in a SOIC body of 14 pins. The NE556 puts two complete timer blocks in a 14-pin SOIC, and the two halves share only the supply and ground. Each half has its own trigger, threshold, discharge, control voltage and reset, so one can run as an astable oscillator while the other runs as a one shot with no interaction. The supply range, the 200 mA output stage and the two thirds threshold are the same as the single timer.
Order code and package
| Order code | NE556DR |
| Function | dual precision timer, two independent blocks |
| Package | SOIC, 14 pins, body code D |
| Supply range | 4.5 V to 16 V |
| Output current | 200 mA per output |
| Threshold | two thirds of the supply on each half |
| Trigger | one third of the supply on each half |
| Modes per half | monostable, astable, bistable or Schmitt trigger |
| Shared pins | supply and ground only, plus the common discharge rail on some pinouts |
| Reset | active low per half |
| Datasheet | SLFS023, NA556, NE556, SA556 and SE556 families |
Electrical parameters that decide the application
| Supply current | twice the single timer for two active halves, and less when one half is idle |
| Output high at 200 mA | 3.3 V minimum on a 15 V supply |
| Monostable period | 1.1 times the product of the timing resistor and capacitor, per half |
| Astable frequency | 1.44 divided by the capacitor times the sum of the two resistors, per half |
| Cross coupling | none, the halves share only the supply pins |
| Temperature grade | 0 C to 70 C for the NE556 |
| Output configuration | totem pole per half |
| Discharge | open collector per half |
| Package options | D SOIC, DB SSOP, N PDIP and NS SO bodies in the family |
| Control voltage | brought out per half for bypassing or modulation |
Points to check before this part goes on a BOM
The two halves are independent but they share a supply pin, so a large current pulse on one output appears as a supply dip for the other. With a 200 mA output switching into a load, a 100 nF capacitor at the package and a separate trace to the supply are what keeps the second timer's threshold from moving during the pulse.
Using one half as a one shot and the other as an oscillator is the classic sequencer arrangement, and it works because the timing components do not interact. The oscillator's discharge pin and the one shot's trigger are separate pins, so the connection between them is a single wire and no level shifting is needed on a common rail.
Current consumption doubles when both halves run. At 15 V that is about 20 mA, which is a real load on a small supply and a real heat source in a 14-pin SOIC, so a product that uses both halves continuously should check the package temperature rather than assume the timer is free.
The threshold and trigger dividers are internal resistor ladders per half, and their absolute value is not tight. That is why the timing formulas are approximate and why a circuit that needs a precise period uses an external reference into the control voltage pin rather than the internal divider.
A common failure mode in repair is a single half dead while the other works. Because the halves share only the supply, that pattern points at the timing components or the load on that half, and swapping the whole package without checking the external parts repeats the failure.
Where this order code fits
Sequencers that need a delay and a pulse from the same package, two channel flashers, and boards replacing two single timers to save area are the reasons this code is ordered, especially in repair where the footprint already has 14 pins. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can the two halves run at different frequencies? Yes. Each half has its own timing resistor and capacitor, and the only shared node is the supply, so two completely different periods run at the same time.
Is NE556DR pin compatible with two NE555DR parts? No, the pinout is a 14-pin arrangement that interleaves the two timers. A board built for two 8-pin timers cannot take this package without a new footprint.
How much current does it draw with both halves active? About twice the single timer, so near 20 mA at 15 V. That matters in a battery product and it is the reason the package temperature rises on a continuous duty cycle.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.