Contact Us

NE5532ADR

Brand: Texas Instruments
Texas Instruments NE5532ADR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

NE5532ADR — Power Management & Signal Chain | Superb Automation

NE5532ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The NE5532ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

NE5532ADR: dual low noise operational amplifier with 12 MHz bandwidth in an 8-pin SOIC

NE5532ADR is a dual low noise bipolar operational amplifier with a 5 nanovolt input noise figure and enough output drive for audio and line level work in a SOIC body of 8 pins. The NE5532 is the low noise member of the 5532 family and the ADR code is the A grade in an 8-pin SOIC on tape and reel. Unity gain bandwidth is 12 MHz, the slew rate is specified at 5 volts per microsecond, the input noise density is 5 nanovolts per root hertz at 1 kHz, and the output stage sinks and sources enough current to drive a 600 ohm load at line level. Both amplifiers are internally compensated and stable at unity gain.

Order code and package

Order codeNE5532ADR
Functiondual low noise operational amplifier
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 3 V to plus or minus 20 V, 5 V to 15 V recommended per rail pair
Unity gain bandwidth12 MHz
Slew rate5 volts per microsecond
Input noise5 nanovolts per root hertz at 1 kHz, 8 nanovolts at 30 Hz
Output drive600 ohm load at line level
Compensationinternal, stable at unity gain
GradeA grade, the tighter offset selection of the family
DatasheetSLOS075, NE5532x and SA5532x family

Electrical parameters that decide the application

Input offset current10 nA typical, 150 nA maximum
Input bias current200 nA typical, 800 nA maximum
Common mode rejection70 dB minimum, 100 dB typical
Large signal gain100 volts per millivolt typical at 25 C
Supply current6 mA typical and 16 mA maximum for the dual
Output short circuit current38 mA
Supply rejection80 dB minimum, 100 dB typical
Input resistance30 kilohm to 300 kilohm, bipolar input
Temperature grade0 C to 70 C for the NE5532, minus 40 to plus 85 C for the SA5532
Protectioninput diodes and output short circuit protection

Points to check before this part goes on a BOM

The 5 nanovolt figure is a 1 kHz number and it rises at low frequency: 8 nanovolts per root hertz at 30 Hz. In a band from 20 Hz to 20 kHz that difference is a few tenths of a microvolt at the input, which matters only when the source impedance is low enough that the amplifier noise dominates the resistor noise.

A 200 nA input bias current is the price of the bipolar input. Through a 10 kilohm source resistance it is 2 mV of offset, which swamps the A grade offset selection, so this part belongs on low impedance sources or behind a blocking capacitor with the bias current returned to ground on the source side.

The 600 ohm drive capability and the 38 mA short circuit current are what make this part an audio part. Driving 600 ohms at 10 V peak to peak is 8.3 mA and 21 mW in the load, well inside the output stage, while the same amplifier driving 150 ohms would run out of current before it ran out of voltage.

Slew rate sets the full power bandwidth. At 5 volts per microsecond and a 10 V peak to peak output, the limit is about 80 kHz, so a 20 kHz signal at that level is inside the part with a factor of four of margin, and a 100 kHz signal at the same level is not.

Supply current of 6 mA typical for the dual is 3 mA per amplifier, which is high for a battery product and irrelevant for a mains powered one. The part also runs warm at plus or minus 18 V, where 16 mA maximum across a 36 V total rail is 0.58 W in an 8-pin body, so the supply choice is a thermal choice as well.

The A grade selects the tighter offset window, not the noise. Both grades share the 5 nanovolt figure, so paying for the A grade buys a smaller direct current error and nothing at all in the noise floor, which is the number most audio circuits are looking at.

Where this order code fits

Microphone preamplifiers, mixing console channel strips, active filters and low noise instrumentation front ends use this part, and it survives in new projects because a 5 nanovolt bipolar input is still hard to beat at the price. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the A grade lower noise than the standard grade? No. The noise figure is the same at 5 nanovolts per root hertz. The A grade tightens the offset current and the offset voltage selections.

Can it run from a single 5 V supply? Not usefully for audio. The input common mode range is roughly 12 V wide around the rails at plus or minus 15 V, and a single 5 V rail leaves almost no room. A single supply circuit needs a split rail or a different part.

Why does my circuit read 2 mV of offset with a 10 kilohm source? That is the 200 nA bias current through the source resistance. The A grade offset selection cannot help, and the cure is a lower source impedance or a bias current compensation resistor on the other input.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.