Contact Us

MSP430F123IDW

Brand: Texas Instruments
Texas Instruments MSP430F123IDW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MSP430F123IDW — Power Management & Signal Chain | Superb Automation

MSP430F123IDW

Texas Instruments — Power Management & Signal Chain

Product Overview

The MSP430F123IDW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MSP430F123IDW: 16 bit ultra low power microcontroller with 8 KB flash in a 28-pin wide body SOIC

MSP430F123IDW is the 8 KB member of the x12x family, otherwise identical to the 4 KB code beside it in a SOIC body of 28 pins. This code is the same x12x die with 8 KB of main flash instead of 4 KB, in the same 28-pin wide body SOIC. Every peripheral, pin and current figure is shared with the 4 KB member: one Timer_A with three capture and compare registers, one USART, comparator_A, 256 bytes of RAM and the same 1.8 V to 3.6 V supply.

Order code and package

Order codeMSP430F123IDW
Function16 bit RISC mixed signal microcontroller
PackageSOIC, 28 pins, wide body, code DW
Flash8 KB plus 256 bytes of information memory
RAM256 bytes
Supply range1.8 V to 3.6 V
Timersone 16 bit Timer_A with three capture and compare registers
Serialone USART, UART or SPI
Analogcomparator_A, no ADC
I/O22 pins
DatasheetSLAS312 revision C, shared with the 4 KB member

Electrical parameters that decide the application

Active current200 microamps at 1 MHz from 2.2 V
Standby current0.7 microamps
Off current0.1 microamps with RAM retained
Wake up timeunder 6 microseconds
Flash organisation16 main segments of 512 bytes plus two information segments of 128 bytes
Endurancethe family document gives the flash endurance and retention figures for this part
Core16 bit RISC, 125 nanosecond instruction cycle at 8 MHz
Supply supervisionpower on reset and a watchdog timer
Clock sourcesDCO, external crystal, external resistor or clock input
ProgrammingJTAG or bootstrap loader on port 1 pins

Points to check before this part goes on a BOM

Doubling the flash does not change the RAM, and 256 bytes is the constraint that decides how this part is programmed. A receive buffer of 64 bytes, a transmit ring of 32 bytes and a few state machines consume most of the space, so a protocol stack that keeps frames in RAM has to stream them rather than buffer them.

The extra flash matters most for calibration data and for a boot loader. Because the information segments are separate from main memory, a boot loader placed in the top main segments can rewrite the application below it without erasing itself, which is the arrangement the F123 supports and the F122 has less room for.

Code size on this core is compact, around one instruction per byte of source for simple logic, so 8 KB holds a metering application with a display driver and a serial protocol. The limit arrives with floating point and with library formatted output, both of which pull in several kilobytes of support code.

The current figures do not change with the flash size in any meaningful way, so a move from the 4 KB code to this one is electrically transparent. The two codes share a datasheet, a pinout and a temperature range, and they are interchangeable on a board that has the flash header wired for the larger device.

Comparator_A plus the timer is enough for a sigma delta measurement built in firmware, and that is how these parts were used before cheap converters arrived. It costs CPU time and a reference, and it is the reason a board built around this family can measure a sensor without an external converter if the accuracy requirement is modest.

Where this order code fits

Projects that outgrow 4 KB are the usual reason this code exists: a meter with a display and a protocol stack, a sensor node that keeps a calibration table, or a product whose firmware is expected to grow during its life. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is this pin compatible with MSP430F122IDW? Yes. Same package, same pinout, same datasheet, 4 KB more flash. A board built for the 4 KB part accepts this one without a change.

Why choose it over the F133 with an ADC? Only if the application needs a comparator and not a conversion. The F133 adds a 12 bit converter, two timers and a larger package, and the board area is the trade.

How is the flash programmed in production? Through the JTAG pins or through the bootstrap loader on port 1, with no external programming voltage required. The loader is the route used when no header is fitted.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.