MC34063ADR
Product Specifications
MC34063ADR
Texas Instruments — Power Management & Signal Chain
Product Overview
The MC34063ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
MC34063ADR: 1.5 A switch mode converter controller in an 8-pin SOIC, commercial temperature grade
MC34063ADR is the commercial temperature version of the same 1.5 A switching converter controller in a SOIC body of 8 pins. MC34063A is the 0 C to 70 C grade of the part that appears on a very large number of legacy boards, and the electrical table is the same one printed for the wide temperature code. The input range, the 1.5 A switch, the 1.25 V reference and the 100 kHz oscillator are identical, so the choice between the two codes is a question of the coldest temperature the board has to start at rather than of performance.
Order code and package
| Order code | MC34063ADR |
| Function | switching regulator controller with an internal output switch |
| Package | SOIC, 8 pins, body code D |
| Input range | 3 V to 40 V |
| Switch current | 1.5 A peak |
| Reference | 1.25 V, 2 percent |
| Oscillator | up to 100 kHz |
| Temperature grade | 0 C to 70 C |
| Wide grade alternative | MC33063A covers minus 40 to plus 85 C on the same die |
| Current limit sense | 300 mV nominal, 250 mV to 350 mV spread |
| Datasheet | SLLS636 revision N, one document for both grades |
Electrical parameters that decide the application
| Oscillator frequency | 33 kHz typical with a 1 nF timing capacitor |
| Switch saturation | 1.0 V typical at 1 A in the Darlington connection |
| Non-Darlington saturation | 0.45 V typical at 1 A with a forced beta of 20 |
| Supply current | 4 mA maximum |
| Thermal resistance | 97 C per watt in the SOIC body |
| Reference window | 1.225 V to 1.275 V at 25 C |
| Comparator bias current | 20 nA typical |
| Switch leakage | 100 microamps maximum at 40 V and 25 C |
| Packaging | tape and reel, lead free |
| Temperature range effect | every parameter is guaranteed over 0 C to 70 C instead of minus 40 C to 85 C |
Points to check before this part goes on a BOM
The 0 C lower limit is the whole difference and it matters on a board that is stored outdoors. A converter built with this code and started at minus 20 C is outside its characterised range, and the oscillator and the reference are the two blocks whose behaviour at cold is not guaranteed, so a cold start check on a bench is not a substitute for the right grade.
Every other number is shared with the wide grade, including the 40 V input ceiling, the 1.5 A switch and the 300 mV current limit sense. That makes this code a legitimate second source for a board built around the wide grade as long as the ambient stays above 0 C, and an illegitimate one for anything that ships to a cold climate.
The 70 C upper limit is generous for a commercial product and tight for an enclosure with no airflow. The junction runs above the ambient by 97 C per watt of loss, so a 0.5 W loss at a 60 C ambient puts the junction at 108 C, inside the 150 C maximum but well outside the characterised range for every parameter that matters.
Repair demand is a real part of the volume for this code. Boards built in the 1990s and 2000s used it in hundreds of circuits, and the same footprint accepts either temperature grade, so a service organisation can fit whichever grade is on the shelf and note the ambient limit on the repair record.
The internal switch means no external MOSFET and no gate drive, which is why the part survives in 24 V industrial projects where a modern controller would need a driver, a MOSFET and a current sense resistor. The cost of that integration is the 1.0 V saturation and the 4 mA quiescent current.
Where this order code fits
Consumer and commercial power supplies, automotive accessory converters that stay inside the cabin range, and repair demand for boards already built around the part are the reasons this code is still ordered in volume. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can this replace MC33063A on an existing board? Electrically yes, mechanically yes, and thermally yes. The restriction is the 0 C to 70 C range, so it is a valid swap only where the board never starts below freezing.
What limits the output current at 12 V input? The peak switch rating of 1.5 A and the thermal rise in the SOIC body. In practice the thermal limit arrives first at around 0.7 W of switch loss.
Is the oscillator fixed? No. The timing capacitor and the pin 5 connection set the frequency up to about 100 kHz, with 33 kHz as the typical result for 1 nF.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.