Contact Us

LSF0108PWR

Brand: Texas Instruments
Texas Instruments LSF0108PWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LSF0108PWR — Power Management & Signal Chain | Superb Automation

LSF0108PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LSF0108PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LSF0108PWR: 8 channel bidirectional level translator with no direction pin in a 20-pin TSSOP

LSF0108PWR is an eight channel bidirectional voltage translator that works from a low side reference as low as 0.65 V up to a 5 V high side in a TSSOP body of 20 pins. The LSF0108 is a passive translation switch rather than a buffered translator: it has no direction pin, no output driver and no fixed logic thresholds, and the low side reference voltage sets what the A port can reach. One reference pin defines the low side, a second defines the high side, and an enable pin puts all eight channels into high impedance. Throughput is specified as 100 MHz upward translation at a 30 pF load and 40 MHz at 50 pF.

Order code and package

Order codeLSF0108PWR
Function8 channel bidirectional voltage level translator, no direction pin
PackageTSSOP, 20 pins, body code PW
Low side reference0.65 V to 3.3 V, set by Vref_A
High side reference1.8 V to 5 V, set by Vref_B
Channelseight, each a passive switch between an A pin and a B pin
Translation pairs0.65, 0.95, 1.2, 1.8, 2.5 and 3.3 V up to 5 V
Enable pinreferenced to the low side supply, pulls all channels to high impedance
Throughput100 MHz upward at 30 pF, 40 MHz up or down at 50 pF
I/O tolerance5 V tolerant ports, so a 3.3 V side can meet a 5 V bus
Latch-upbetter than 100 mA per JESD 17
DatasheetSCES871, LSF family

Electrical parameters that decide the application

On resistance at Vref_A 1 V, 64 mA5 ohm typical
On resistance at Vref_A 1.8 V, 64 mA4 ohm typical
On resistance at Vref_A 2.5 V3 ohm typical
On resistance at Vref_A 3.3 V3 ohm typical
On resistance at Vref_A 0.65 V, 20 mA15 ohm typical
Reference voltage range0 V to 5.5 V on both reference pins and on enable
Enable pull-up200 kilohm to Vref_B is the recommended arrangement
Capacitive load ceiling30 pF for the 100 MHz figure, 50 pF for the 40 MHz figure
Pinoutflow through, A pins on one side and B pins on the other
Clamp behaviourthe A side voltage is limited by Vref_A, which is what sets the low side logic high

Points to check before this part goes on a BOM

The switch resistance is a function of the low side reference, and the difference is large. At Vref_A of 3.3 V the channel is 3 ohm and a 64 mA pull-down moves 190 mV, but at 0.65 V it is 15 ohm and the same current would need 0.96 V, which the rail cannot supply. That is why the 0.65 V column is specified at 20 mA and not at 64 mA.

There is no driver in this part, so the edge rate depends on the pull-up resistor and the bus capacitance. A 4.7 kilohm pull-up against 50 pF is a 235 ns time constant, well under the 40 MHz that the table allows at that load, which tells you the throughput figure assumes a low resistance pull-up and a short bus rather than the resistor a low power I2C bus usually carries.

The high side is defined by Vref_B and the low side by Vref_A, and the A pin voltage is clamped to Vref_A. A board that powers the low side from a 1.8 V rail therefore cannot put 3.3 V on that side even if the high side is 5 V, and the pull-ups on both sides have to follow their own rail.

The enable pin is referenced to the low side supply and the datasheet recommends a 200 kilohm pull-up to Vref_B. Left floating the channels are not guaranteed to be in a defined state, and pulling enable low puts all eight channels into high impedance without removing power, which is how a bus segment is isolated during a card swap.

Latch-up better than 100 mA per JESD 17 and 5 V tolerant ports are the two figures that make this part usable on mixed voltage backplanes, but neither is a substitute for a series resistor on a connector pin that can be driven by an external board.

A passive translator does not level-shift a clock or a fast serial line for free. At 30 pF and 100 MHz the part is operating at the edge of its specification, and the same channel at 50 pF drops to 40 MHz, so the load budget has to be counted from the connector, the vias and the receiving pin capacitance and not from the driver datasheet.

Where this order code fits

Boards that join a 1.8 V or 2.5 V processor to 3.3 V or 5 V peripherals use this part, typically on I2C, SMBus, PMBus and SPI buses where several devices sit on the same pair of wires and the direction changes with every transaction. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it translate a 0.65 V bus up to 5 V? Yes, and that is the lowest pair in the table, but the channel is 15 ohm at that reference and specified at 20 mA, so the load has to be light and the pull-up has to suit a low voltage rail.

Does the part need a direction pin? No. The channel is a switch that conducts in both directions, which is why I2C, SMBus and PMBus work without any arbitration from the host.

Is the enable pin optional? It can be tied to the low side rail through the recommended 200 kilohm pull-up, and then it is always on. Driving it low isolates all eight channels without removing the supplies.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.