LP2985IM5X-3.3
Product Specifications
LP2985IM5X-3.3
Texas Instruments — Power Management & Signal Chain
Product Overview
The LP2985IM5X-3.3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LP2985IM5X-3.3: 150 mA low-noise low-dropout regulator with shutdown, fixed at 3.3 V in a 5-pin SOT-23
LP2985IM5X-3.3 is a fixed 3.3 V low-dropout linear regulator rated 150 mA, with a shutdown pin and a bypass pin for the noise figure in a SOT-23 body of 5 pins. The IM5X suffix unpacks into three separate facts: the industrial temperature grade, the 5-pin SOT-23 body coded DBV, and tape and reel packing. The output is fixed at 3.3 V, the input works from 2.5 V to 16 V, and the silicon in this order code is the legacy chip, which is the detail that decides whether the accuracy in a quotation is 1.5 percent or 0.5 percent, because those two figures belong to two different dies that share the LP2985 name.
Order code and package
| Order code | LP2985IM5X-3.3 |
| Function | fixed 3.3 V low-noise low-dropout regulator with shutdown |
| Package | SOT-23, 5 pins, body code DBV |
| Input range | 2.5 V to 16 V on the new chip, 16 V absolute maximum on both dies |
| Output current | 150 mA |
| Accuracy grade | 1.5 percent, standard grade of the legacy chip |
| Silicon | legacy chip, not the new chip that carries the 0.5 percent figure |
| Bypass pin | fitted, 10 nF gives the published 30 microvolt RMS noise |
| Output capacitor | 2.2 microfarad ceramic, inside the published stable ESR window |
| Thermal shutdown | 170 C junction, with current limit ahead of it |
| Junction range | minus 40 to plus 125 C |
| Datasheet | SLVS514, LP2985 family, covering both dies |
Electrical parameters that decide the application
| Accuracy over load and temperature | 0.5 percent new chip, 1 percent A grade legacy, 1.5 percent standard grade legacy |
| Dropout at 150 mA | 180 mV typical and 198 mV maximum new chip, 280 mV typical and 350 mV maximum legacy |
| Dropout over full temperature | 254 mV new chip, 575 mV legacy |
| Ground pin current at 0 mA | 69 microamps typical new chip, 65 microamps typical legacy, 95 microamps maximum on both |
| Ground pin current at 150 mA | 850 to 1200 microamps on the legacy chip |
| Output noise | 30 microvolts RMS with a 10 nF bypass capacitor on the BYP pin |
| Ripple rejection | 70 dB at 1 kHz falling to 40 dB at 1 MHz |
| Shutdown current | 0.01 microamps typical legacy, 1.12 microamps typical new chip |
| Thermal resistance | 205.4 C per watt on the legacy die in SOT-23-5, 178.6 C per watt on the new die |
| Output voltage options | 1.2 V to 5.0 V in 100 mV steps on the new chip |
Points to check before this part goes on a BOM
The accuracy in the family headline is not the accuracy in this reel. The 0.5 percent figure belongs to the new chip, the A grade of the legacy chip is 1 percent, and this standard grade code is 1.5 percent over load and temperature. On 3.3 V that is a 3.25 V to 3.35 V window, which spends 35 mV of a plus or minus 2 percent load budget before the load itself moves.
Dropout on the legacy die is 280 mV typical and 350 mV maximum at 150 mA, and 575 mV maximum over the full temperature range. A 3.3 V output therefore needs at least 3.65 V at full load and 3.88 V over temperature, so a 3.3 V backplane cannot feed this part at all and a 5 V rail has 1.1 V of margin at 125 C.
Dissipation from 5 V to 3.3 V at 150 mA is 255 mW, and the SOT-23-5 figure is 205.4 C per watt on the legacy die, which is a 52 C rise on a JEDEC board. A 70 C ambient then puts the junction at about 122 C against a 125 C limit, so the 150 mA rating is a thermal number on this body and 100 mA is the sane continuous figure.
Ground pin current at 150 mA is 850 to 1200 microamps, under one percent of the load, but at 1 mA of load the same 95 microamp maximum is 9.5 percent of the load, so light-load efficiency on this part is set by its own quiescent current rather than by the 5 V to 3.3 V ratio.
The published stable window is drawn for a 2.2 microfarad output capacitor at 2.3 V and above, and the new chip caps supported ESR at 1 ohm. A board that has been running an old high-ESR tantalum can therefore fall outside the window after a silicon change even though the reel label looks the same.
30 microvolts RMS is 0.037 of one least significant bit on a 12 bit converter with a 3.3 V reference, where a bit is 806 microvolts. That number requires the 10 nF bypass capacitor, and the rejection behind it falls from 70 dB at 1 kHz to 40 dB at 1 MHz, so 100 mV of 1 MHz ripple from an upstream converter still arrives as 1 mV.
Where this order code fits
Post regulation behind a switching supply, quiet rails for sensors and transceivers, and 3.3 V housekeeping rails on industrial and telecom boards are the three places this code turns up, usually because the board already has 5 V and needs one clean 3.3 V rail at a few tens of milliamps. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is LP2985IM5X-3.3 a different part from LP2985IM5-3.3? No. The trailing X is tape and reel packing and the rest of the string carries the meaning: M5 is the SOT-23-5 body, I is the industrial grade and 3.3 is the fixed output. The characters that do change a part are the voltage suffix, the accuracy grade and the body code.
Can this regulator hold 3.3 V from a 3.3 V rail? No. It needs 350 mV to 575 mV of headroom at 150 mA depending on temperature, so the input has to sit above 3.9 V for full load over temperature, and a 5 V rail is the normal supply.
Does the bypass pin have to be used? Only when the noise figure is part of the requirement. The 30 microvolt RMS number is measured with 10 nF on that pin, and an unbypassed part still regulates but is noisier than the table says.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.