Contact Us

LM319AMX-NOPB

Brand: Texas Instruments
Texas Instruments LM319AMX-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM319AMX-NOPB — Power Management & Signal Chain | Superb Automation

LM319AMX-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM319AMX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM319AMX-NOPB: the A grade dual high speed comparator on a reel

LM319AMX-NOPB is the A grade of the dual high speed comparator in the fourteen pin small outline body, on a 2500 piece reel, specified from 0 to plus 70 degrees. It is a different circuit from the LM293 family and a different set of trade offs: 80 nanoseconds of response instead of 1.3 microseconds, plus or minus 15 volt rails instead of a single 5 volt supply, and 4.3 milliamps of supply current instead of half a milliamp.

The part is built for the jobs where a slow comparator is the limit. A zero crossing detector in a switching supply, a peak detector in a pulse chain, a discriminator in an instrument front end and a fast over current trip all sit inside the 80 nanosecond window that this device opens.

The NOPB suffix is a lead free declaration inherited from the original vendor, and it is the reason the string looks longer than the electrical table needs.

The A grade against the plain grade

The A sort holds 0.5 millivolts typical and 1 millivolt maximum of offset at 25 degrees, measured with a 5 kilo ohm source. The plain LM319 holds 2 millivolts typical and 8 maximum on the same condition. That is a factor of eight on the maximum, which is the largest grade gap in the family and the reason the A sort survives in precision pulse work.

The bias rows separate in the same direction. Offset current is 20 nanoamps typical and 40 maximum on the A sort, against 80 and 200 on the plain. Bias current is 150 nanoamps typical and 500 maximum, against 250 and 1000. At a 5 kilo ohm source the bias current contributes under 3 millivolts on the A sort, which is why the offset row is quoted at that impedance.

Orderable codeLM319AMX-NOPB
Comparators per body2, independent
BodySOIC, 14 pins
Carrierlarge tape and reel, 2500 pieces
Part markingLM319AM
Temperature window0 to plus 70 degrees
Offset at 25 degrees0.5 millivolts typical, 1 maximum
Offset over the window10 millivolts maximum
Input offset current20 nanoamps typical, 40 maximum
Input bias current150 nanoamps typical, 500 maximum
Response time with 5 millivolts of overdrive80 nanoseconds typical
Input voltage range on plus or minus 15 voltsplus or minus 13 volts
Output saturation at 25 milliamps0.75 volts typical, 1.5 maximum
Output leakage at 35 volts0.2 microamps typical, 10 maximum
Positive supply current4.3 milliamps typical, 8 maximum
Negative supply current3 milliamps typical, 5 maximum

The supply rules that the document states plainly

Two rules govern this device and both are printed in the same paragraph as the electrical table. The first is that the offset, offset current and bias current rows apply on any supply from a single 5 volt rail up to plus or minus 15 volts, so the input stage behaves consistently across the range. The second is that the device must not be operated with more than 16 volts from ground to either supply pin.

The 16 volt rule is the one that catches an engineer who is used to a 36 volt comparator. Feeding this part from a 24 volt rail destroys it. Feeding it from plus or minus 15 volts is inside the rating at 15 volts from ground, and the input range on that supply is plus or minus 13 volts, so a signal that swings to the rail needs attenuation rather than a bigger supply.

Supply current is quoted separately for each rail, 4.3 milliamps positive and 3 milliamps negative, which is a detail that matters when the negative rail comes from a charge pump with a limited budget. A dual comparator that draws 7.3 milliamps total is not a micropower part, and the quiescent figure does not fall when the outputs are static.

The output, the strobe and the load above the rail

The output stage is a transistor with an open collector and an open emitter, drawn to sink 25 milliamps with a 0.75 volt saturation. The 10 microamp leakage at 35 volts is the number that decides the pull up: on a 1 kilo ohm resistor it is 10 millivolts, and on 100 kilo ohms it is a volt, which is enough to hold a following gate in the wrong state.

The device is specified with the output pulled up to 15 volts through a 1.4 kilo ohm resistor, and that is the condition behind the gain figure. A different pull up changes the gain and the edge, so a bench measurement that does not match the table should be checked against that resistor first.

Because the emitter is available, the output can sit on a rail below the negative supply of the following stage, which is how the part drives a level shift into a ground referenced logic input from a plus or minus 15 volt front end. That single property is why the device outlived faster comparators that only offer a ground referenced output.

Why this string and not the tube

The reel body is the same die as the tube, and the 2500 piece carrier is what an instrument line with a feeder wants. A bench that builds tens of boards wants the tube, and a build that needs a few hundred pieces wants a cut length. The electrical table does not change with any of them.

Our pin to pin cross reference page covers the substitutions that keep the fourteen pin footprint, which matters here because the pinout is not the same as the quad comparator in the same body size. The defense grade components page sets out what changes when the same function has to come from a part with a wider window and a qualification record.

Sourcing note. This family is old enough that several catalogue listings show the same body under four or five strings, differing in lead free declaration, carrier and grade. The electrical table is the only reliable way to tell them apart, and the A sort is worth the premium whenever the input source impedance is above a few kilo ohms.

Where an 80 nanosecond comparator earns its place

Three instrument functions depend on this speed. A peak detector that has to catch a pulse shorter than a microsecond, a zero crossing detector in a switching supply where the delay becomes a phase error, and a discriminator that separates two pulse heights a hundred millivolts apart. In each case the comparator is not doing arithmetic, it is making a decision before the signal has moved on.

The peak detector is the most demanding of the three. The diode drop and the hold capacitor set the droop, and the comparator sets how much of the peak is missed. At 80 nanoseconds the part captures a pulse that a 1.3 microsecond device would round off by 6 percent of a 5 microsecond pulse, which is the difference between a usable reading and a calibration table that has to be corrected.

What the wide input range buys

Plus or minus 13 volts of input range on plus or minus 15 volt rails lets the part sit directly on a sensor output that swings several volts either side of ground, with no attenuation and no level shift. Attenuation costs signal to noise at the input, and a level shift costs an amplifier and its own offset, so the wide range is worth more than the two volts of headroom it costs.

The same range is why the part appears in front of analogue to digital converters in older instrument chains, where the comparator has to resolve a threshold on a signal that has not yet been scaled to the converter's window.

Questions that come with this code

Is the part single supply? It runs from a single 5 volt rail, and the offset rows hold there, but the input range collapses to the 5 volt window, so most circuits use split rails.

What kills this device in the field? Exceeding 16 volts from ground to a supply pin, and driving the output into a load that pulls the collector above 35 volts.

Does the A grade help at 70 degrees? The offset maximum over the window is 10 millivolts on the A sort against 10 on the plain sort in the same table, so the A advantage is a room temperature advantage and the window figure has to be read separately.

Can it drive a relay? At 25 milliamps and 1.5 volts saturation it can drive a small relay coil, and the flyback diode is still required.