LM317MQDCYR
Product Specifications
LM317MQDCYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM317MQDCYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM317MQDCYR: the automotive grade 500 mA regulator in SOT-223
LM317MQDCYR is the 500 mA member of the LM317 family in the four pin SOT-223 body on a 2500 piece reel, with the Q marking the automotive grade. The device is a floating three terminal regulator with an output window of 1.25 V to 37 V, so the same circuit that produces 5 V from 12 V can produce 30 V from 40 V with two resistors and no ground reference.
SLVS297R, revised May 2026, covers both the plain LM317M and the automotive LM317MQ. The automotive part is qualified to AEC-Q100 grade 2, which is printed as minus 40 to 105 degrees ambient, while the junction window in the ordering table is minus 40 to 125 degrees. Those two numbers are not the same window and a thermal calculation that uses the junction figure as an ambient figure will under count the derating by 20 degrees.
What follows is what the Q grade adds, the electrical rows that hold across both chips, the thermal arithmetic that decides between SOT-223 and TO-252, and the reason an automotive string is bought by date code rather than by price.
What the automotive marking adds
The Q grade is a qualification statement on top of the same circuit. AEC-Q100 grade 2 covers the ambient range of minus 40 to 105 degrees, and the ordering table prints the junction window as minus 40 to 125 degrees with a part marking of L5 on the SOT-223 reel row. The plain M grade in the same table carries marking L4 and the same junction window, so the difference is the qualification file and the ambient rating, not the silicon window.
| LM317MQDCYR | SOT-223, 4 pins, 2500 pieces on a large reel, minus 40 to 125 degrees junction |
| Automotive qualification | AEC-Q100 grade 2, minus 40 to 105 degrees ambient |
| Part marking | L5 |
| Moisture rating | level 3, 260 degrees for 168 hours |
| LM317MDCYR | SOT-223, 4 pins, 2500 pieces on a large reel, marking L4, moisture level 2 |
| LM317MDCY | SOT-223, 4 pins, 80 pieces per tube, moisture level 2 |
| LM317MDCYRM3 | SOT-223, 4 pins, 2500 pieces on a large reel, marking L5 |
| TO-252 body | KVU, 3 pins, junction to ambient 31.7 degrees per watt on the new chip |
| SOT-223 body | DCY, 4 pins, junction to ambient 77.7 degrees per watt on the new chip |
| Output current class | 500 mA |
| Reference voltage | 1.2 V minimum, 1.25 V typical, 1.3 V maximum |
| Line regulation at 25 degrees | 0.01 percent per volt typical, 0.04 maximum |
| Load regulation at 25 degrees | 0.1 percent typical, 0.5 maximum |
| Adjustment pin current | 50 microamps typical, 100 maximum |
| Minimum load current | 3.5 milliamps typical, 10 maximum |
| Output voltage stability with temperature | 0.7 percent legacy chip, 1 percent new chip |
The rows that decide a 500 mA rail
Line regulation of 0.04 percent per volt maximum means a 12 V input that sags to 9 V moves the output by 0.12 percent, which on a 5 V rail is 6 millivolts. That is good enough for an analog rail and it is the reason the part survives in automotive modules where the input moves with the battery and the load dump clamp.
The current limit row is the one that matters for a module that feeds a harness. The table prints a maximum output current of 500 mA on the new chip with a peak row that reaches 900 mA on the legacy chip and 1.6 A on the new chip at a 15 V differential with the package at its dissipation limit. A short on the harness will therefore pull well over the continuous rating until the thermal path gives up, so the fuse or the series resistor in front of the regulator is doing the protection work and the device is the second line.
Minimum load current of 3.5 milliamps typical and 10 maximum is a real constraint in an automotive standby circuit, because a module that sleeps at 200 microamps cannot afford a 10 milliamp bleeder, and a rail that goes open circuit will float up toward the input until something else on the board clamps it. The usual answer is to keep one always on load, a comparator or a CAN transceiver in standby, on the regulated rail so the regulator never sees an open circuit.
Thermal arithmetic between the two bodies
The SOT-223 is printed at 77.7 degrees per watt junction to ambient on the new chip and the TO-252 at 31.7. Those figures assume the copper plane stated in the thermal section, and they are the difference between a board that works and one that folds back in a hot enclosure. At 500 mA and a 7 V differential the device dissipates 3.5 W, which is 272 degrees of rise in the SOT-223 and 111 degrees in the TO-252, so the SOT-223 is only viable at that load with a plane and airflow, while the TO-252 holds the same load on a modest plane at 85 degrees ambient.
The practical split is load against differential. Below 1 W the SOT-223 is fine with a plane under the tab, between 1 W and 2 W it needs the plane plus a quiet enclosure, and above 2 W the TO-252 is the only one of the two that holds. A 12 V to 5 V rail at 300 mA dissipates 2.1 W, which sits in the middle band and is the case where the body choice is decided by the enclosure rather than by the electrical table.
Why an automotive string is bought by date code
An automotive line does not release a lot on price. The part has to carry a traceable date code, a lot number and a document that ties the reel to the qualification file, and a broker reel with no paperwork is a liability even when the marking is correct. Moisture level 3 at 260 degrees for 168 hours also puts a floor life on the reel once the bag is opened, so a partial reel that has been open for a week needs a bake before it goes on the line.
RLS297R prints the same silicon under three strings, the plain M, the M with an M3 suffix and the MQ with a Q1 suffix for the automotive flow. The suffix decides which qualification document a buyer can ask for, and that document is what an auditor reads. The supplier quality audit page sets out what we ask for when a Q grade is quoted without a traceability pack, and the date code management page covers the bake and floor life rules we apply to level 3 reels.
Questions that come with the Q string
Is the junction window the same as the ambient window? No. AEC-Q100 grade 2 is minus 40 to 105 degrees ambient and the ordering table prints minus 40 to 125 degrees junction, so a board that runs the junction at 120 degrees is inside the device rating and outside the qualification, which is not a defensible position in an audit.
Can the TO-252 body be used where the board has the SOT-223 footprint? No, the pin count and the tab differ, so it is a board change. Where the board is already fixed, the SOT-223 with a plane under the tab is the only option and the load has to be capped accordingly.
Does the part need an output capacitor? The data sheet states stable operation without one across the load range, and an output capacitor is optional for transient response. Where a capacitor is fitted, an electrolytic or a tantalum is what the document describes, because a very low ESR ceramic can interact with the loop on this generation of the circuit.
What is the right reel quantity for a module build? The 2500 piece reel matches a monthly build of about 200 modules for a year, and the 80 piece tube suits a pilot run. Where the volume is between the two, a partial reel with a documented date code is cheaper than carrying a full reel past its floor life.