Contact Us

LM317DCYR

Brand: Texas Instruments
Texas Instruments LM317DCYR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM317DCYR — Power Management & Signal Chain | Superb Automation

LM317DCYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM317DCYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM317DCYR: the adjustable regulator in the four pin SOT-223 body on a reel

LM317DCYR is the adjustable three terminal positive regulator in the four pin SOT-223 body, on a 2500 piece reel, rated 1.5 amps and guaranteed from 0 to plus 125 degrees. It is the small package member of a family that has been in catalogues since 1997 and was revised as recently as 2025, and the revision matters because the document now describes two silicon generations that share the same part number.

The regulator holds 1.25 volts between its output and its adjustment pin and regulates whatever the two resistors around it ask for. That single sentence is the whole device, and the work in using it well is in the thermal path, the adjustment pin current and the output capacitor, not in the equation.

What the string declares and which silicon it carries

LM is the family prefix, 317 is the adjustable positive regulator, DCY is the four pin SOT-223 body, and R is the tape and reel carrier. The body is the one that dissipates through a tab, so the copper under the tab is part of the circuit and not a detail left to the end of the project.

The current document prints a legacy chip column and a new chip column for the same orderable code. The two differ in line and load regulation, in ripple rejection, in thermal resistance and in temperature stability, and nothing on the reel label separates them. A purchaser who needs the tighter rows should ask which silicon the lot carries, because the part number alone no longer answers the question.

Orderable codeLM317DCYR
BodySOT-223, 4 pins
Carriertape and reel, 2500 pieces, 330 millimetre reel, 12.4 millimetre tape
Input range4.25 to 40 volts
Current rating1.5 amps
Temperature window0 to plus 125 degrees
Lead finish and moisturetin, level 2 at 260 degrees, one year floor life
Part markingL3
Junction to ambient66.8 degrees per watt on the legacy chip, 59.6 on the new chip

The reference and the regulation rows

The reference is 1.25 volts nominal with a window of 1.2 to 1.3 volts, which is the number every output calculation starts from. Line regulation is 0.01 percent per volt typical and 0.04 maximum at 25 degrees, widening to 0.02 typical and 0.07 maximum over the operating range, so a 10 volt change on the input moves the output by about 4 millivolts at the maximum.

Load regulation is where the two chips separate. The legacy chip prints 25 millivolts from 10 milliamps to 1.5 amps at outputs of 5 volts or less, and 0.1 percent typical with 0.5 percent maximum above 5 volts. The new chip prints 0.3 percent typical and 1.5 percent maximum over the full range. On a 5 volt output that is 15 millivolts typical against 25 millivolts, so the newer silicon is not automatically the tighter one and the table has to be read row by row.

Reference voltage1.25 volts nominal, 1.2 to 1.3 volts
Line regulation at 25 degrees0.01 percent per volt typical, 0.04 maximum
Line regulation over temperature0.02 percent per volt typical, 0.07 maximum
Load regulation, legacy chip, output at or below 5 volts25 millivolts maximum
Load regulation, new chip, full range0.3 percent typical, 1.5 percent maximum
Adjustment pin current50 microamps typical, 100 maximum
Thermal regulation, 20 millisecond pulse0.04 percent per watt typical, 0.07 maximum
Ripple rejection at 120 hertz64 decibels on the legacy chip, 80 on the new chip

The adjustment pin current is not zero, and the resistor divider knows it

The adjustment pin draws 50 microamps typical and 100 maximum, and that current flows through the lower resistor of the divider. On a 240 ohm lower resistor the error is 12 to 24 millivolts, which is small compared with a 5 volt output and large compared with a 1.25 volt output. Lowering the divider to 120 ohms doubles the standing current and halves the error, which is a trade an engineer makes on a battery powered board only after checking the quiescent budget.

There is a second order effect that shows up on a 1.25 volt output. The regulator cannot hold its output below the reference, so the lowest usable output is 1.25 volts and the practical floor is a little above that once the adjustment pin current is included. A board that needs 1.2 volts from this part needs a different part, not a smaller resistor.

The other half of the same problem is the adjustment pin current change, which is 0.2 microamps typical and 5 maximum over the input range. That change appears directly across the lower resistor as an output error, and on a 240 ohm resistor it is 1.2 millivolts, which is inside the reference window and worth knowing when the output is being compared against a 1 percent measurement.

The thermal path is the real 1.5 amp limit

The SOT-223 tab is the only thermal path, at 66.8 degrees per watt on the legacy chip and 59.6 on the new one. A 12 volt to 5 volt drop at 0.5 amp is 3.5 watts, which is 234 degrees of rise at the legacy number and 209 at the new one, so the part cannot hold that operating point in still air whatever the current rating says.

The practical limit is set by the copper under the tab, the airflow and the ambient. A 6 square centimetre pad on 2 ounce copper gets the junction to ambient path into the 40s, which allows about 2 watts at a 100 degree rise. Anything above that needs a larger package, a switching pre regulator, or both. A series resistor ahead of the regulator is the cheapest way to move dissipation out of the device, and it works only when the load current is predictable.

The series resistor is worth a worked case. A 24 volt input feeding a 5 volt 200 milliamp load through the regulator dissipates 3.8 watts in the device, which no SOT-223 survives. A 33 ohm resistor ahead of it drops 6.6 volts at that current and moves 1.3 watts into the resistor, which leaves 2.5 watts in the regulator and still does not survive. Two things have to change together, the resistor and the load current, and that is the point at which a switching regulator becomes the cheaper answer.

Moisture level 2 and what it means on the line

This body carries a tin finish and a level 2 moisture rating at 260 degrees with a one year floor life, so unlike the nickel palladium gold bodies in the same catalogue it can need a bake after a year in an uncontrolled store. A line that keeps reels in a dry cabinet will never see the bake, and a line that keeps them on a shelf will.

The part marking is L3, which is the marking a customer sees on the body rather than on the label, and that is what an incoming inspection checks when a reel arrives without its label. Our incoming inspection plan page covers that check, and the power management cross reference page lists the fixed voltage regulators that can replace this part when a board does not need adjustability.

Questions that come with this code

Is the output set by a ratio or by an absolute resistor value? By a ratio, with 1.25 volts across the lower resistor and the adjustment current adding to it. That is why 240 ohms is the usual lower value and why 120 ohms is used when the error has to be halved.

Can it run from 3.3 volts? No. The input range starts at 4.25 volts, and a 3.3 volt rail leaves no headroom for a 1.25 volt reference plus the pass element drop. A low dropout regulator is the correct part below 4.25 volts.

Does the output capacitor need a specific value? The family is stable over a wide range of ceramic output capacitors, and the transient response improves with more capacitance. The trap is a tantalum capacitor with a high equivalent series resistance, which is stable but slower than the ceramic it replaced. Our pin to pin cross reference page lists the fixed and low dropout members that share the SOT-223 footprint.