Contact Us

LM239ADR

Brand: Texas Instruments
Texas Instruments LM239ADR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM239ADR — Power Management & Signal Chain | Superb Automation

LM239ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM239ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM239ADR: the A grade quad comparator with a 2 millivolt window

LM239ADR is one of four comparators in a 14 pin SOIC body, on tape and reel, in the A grade. The A is the offset grade and it is the reason this string exists: the base LM239 is specified at 5 millivolts maximum at room temperature, and the A grade halves that to 2 millivolts. On a threshold chain built around a 10 millivolt window, that difference decides whether the product passes first time.

The quad package is the workhorse of analogue threshold work. Four comparators, one supply rail, one ground, a common mode range that includes ground, and an open collector output that can be wired OR with the others. A window comparator, a three level battery gauge, a fan control with hysteresis and a fault latch all fit in one body.

What follows is the numeric detail that matters when the part is used as a threshold rather than as a switch: the offset, the bias current, the input range, the output saturation at 4 milliamps, and the response time that limits how fast a threshold can follow.

What the A grade buys, in numbers

The offset window at 25 degrees is 1 millivolt typical and 2 millivolts maximum, against 2 typical and 5 maximum on the base grade. Over temperature the A grade holds a 4 millivolt maximum where the base grade widens further. The offset current and the bias current are the same rows on both grades, so the A grade is a sorting improvement rather than a different input stage.

That is worth knowing for cost reasons. If a chain is limited by bias current across a high impedance divider, the A grade does not help and the money is better spent on a lower bias part. If the chain is limited by the comparator's own offset, the A grade is the cheapest fix available.

Orderable codeLM239ADR
Comparators per body4
BodySOIC, 14 pins, 8.70 by 3.90 millimetres nominal
Carriertape and reel
Offset at 25 degrees, A grade1 millivolt typical, 2 maximum
Offset over temperature, A grade4 millivolts maximum
Input bias current25 nanoamps typical, 250 maximum
Input offset current5 nanoamps typical, 50 maximum
Common mode rangeground to 1.5 volts below the positive rail at 25 degrees
Output saturation at 4 milliamps150 millivolts typical, 400 maximum
Output sink current16 milliamps typical at 1.5 volts
Supply current, four comparators0.8 milliamps typical, 2 milliamps maximum
Response time1.3 microseconds typical
Temperature windowminus 25 to plus 85 degrees

The input range that includes ground, and why that is the family's selling point

The common mode range starts at ground, which means the inputs can sit at the negative rail without a charge pump and without a split supply. The upper end stops 1.5 volts below the positive rail at 25 degrees and 2 volts below over temperature, and that upper limit is the one that catches people who power the part from 5 volts and compare a signal that swings to 4.5.

One input may exceed the positive rail as long as the other stays inside the range, and both inputs can go to the full supply without damage. That asymmetry is useful in a fault comparator that watches a 24 volt line with a 5 volt supply: the divider brings the line down, and the protective clamp is inside the device rather than on the board.

Going below ground is the one direction that is not allowed by more than 0.3 volts. A signal from a sensor with a negative excursion needs a series resistor or a clamp, and a bipolar signal needs a split supply.

Four comparators, one pull-up, and the wired OR

The output is an open collector transistor with the emitter on the ground pin. Four of them can share a single pull-up, which turns the quad into a wired OR: any comparator that pulls low drags the node low, and the node only rises when all four release. That is the structure of a fault bus, a multi point alarm, and a window comparator's outside-the-window output.

The pull-up value is set by the rise time against the node capacitance and by the sink current. With 4 milliamps of sink and a 400 millivolt saturation ceiling, a 1 kilo ohm pull-up on a 5 volt rail leaves 4.6 volts of swing and a rise time of about 10 microseconds per 10 picofarads of node capacitance. A 10 kilo ohm pull-up is ten times slower and draws a tenth of the current.

Saturation is what sets the low level. At 4 milliamps the guaranteed ceiling is 400 millivolts, and at 16 milliamps the part is still inside its rating but the saturation rises. A logic input that needs 0.4 volts or less to read a valid low is at the edge of the guarantee at 4 milliamps, which is why the pull-up is usually chosen for 2 to 3 milliamps rather than for the maximum sink.

Hysteresis, and why a bare comparator oscillates

A comparator with no hysteresis will oscillate on a slow input. The output changes, the input moves because of the change, and the part chases its own output. Positive feedback through a resistor from the output to the non-inverting input fixes it, and the amount of feedback sets the width of the dead band.

On an open collector output the feedback resistor has to work against the pull-up, so the two are chosen together. A 100 millivolt dead band on a 5 volt rail with a 10 kilo ohm pull-up needs roughly 200 ohms of feedback into a 10 kilo ohm divider, which is a ratio worth calculating rather than guessing.

The response time limits how fast the hysteresis can work. At 1.3 microseconds the part follows a 100 millivolt step in about a microsecond, so a threshold that moves faster than that sees the comparator's delay rather than its threshold.

The arithmetic of a window comparator

Two comparators make a window. The reference divider sets an upper and a lower threshold, one comparator watches each, and the two open collector outputs are wired OR so that either one pulling low means out of window. The width of the window is the difference between two divider taps, and the accuracy of that width is the sum of the two offsets plus the divider tolerance.

With a 2 millivolt offset per comparator a 200 millivolt window is accurate to about 2 percent before the resistors are counted, and a 20 millivolt window is accurate to 20 percent. That is the calculation that decides whether the A grade is enough or whether the thresholds have to be trimmed at test.

Where the quad A grade is the right choice

It is the right choice on any board with several thresholds and a modest accuracy requirement: a three level battery indicator, a fan control with a dead band, a power supply sequencer, a fault latch, a zero crossing detector on a low voltage signal. The four comparators share a supply and a ground, which saves pins and decoupling.

It is the wrong choice for a precision instrument, where 2 millivolts of offset is still too much and a chopper stabilised part is needed, and for a fast signal, where 1.3 microseconds is slow.

Our amplifier cross reference page lists the single, dual and quad equivalents with their offset grades, and the power management cross reference page covers the supply side of the same board.

Buying questions that come with this code

Is LM239ADR the same die as LM239DR? Yes. The A is a tighter offset sort, and the R is the reel. Both are the same 14 pin SOIC body.

Can the four comparators run from 3.3 volts? Yes, the family operates from 2 volts, and the input range still includes ground. The response time lengthens a little at the lower rail.

What replaces it if the reel is short? The LM339 in the same body with a 0 to 70 degree window and a 5 millivolt offset, or the LM2901 with a wider temperature window. Check the offset row before substituting.