LM211QDRG4
Product Specifications
LM211QDRG4
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM211QDRG4 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM211QDRG4: the green reel code on the 125 degree comparator
LM211QDRG4 combines three things that are easy to confuse: the Q temperature grade of the single strobed comparator, the SOIC body on tape and reel, and the green material code. Each field is independent. A buyer who needs minus 40 to plus 125 degrees and a lead free finish has exactly one string to order, and this is it.
The part goes into the same socket as the industrial LM211, so the choice is usually made late, when a thermal survey shows the local ambient above 85 degrees. Swapping the string on the purchase order is the whole change. Nothing on the board moves, and the qualification work is limited to a re-run of the threshold tests at the hot end.
The rest of this page is about the parts of the order that fail quietly: the tape width against the feeder, the moisture level against the floor life, the finish against the solder profile, and the grade against the documentation.
The code read as four separate decisions
LM211 is the family and the input stage. Q is the minus 40 to plus 125 degree window. D is the eight pin SOIC body. R is the reel. G4 is the green material and finish. Every one of those is a decision that can be wrong on its own, and a purchase order that lists only the first five characters leaves three of them to the supplier.
The body matters because the footprint does not change between the tube and the reel variants, but the feeder does. The reel is 330 millimetres with a 12.4 millimetre tape and 8 millimetre pocket pitch, which is the standard SOIC-8 tape and fits any 12 millimetre feeder on a placement machine.
| Orderable code | LM211QDRG4 |
| Grade | Q, minus 40 to plus 125 degrees |
| Body | SOIC, 8 pins |
| Carrier | 2500 pieces, 330 millimetre reel, 12.4 millimetre tape |
| Finish | nickel palladium gold |
| Moisture level | level 1, unlimited floor life at 260 degrees |
| Electrical rows | identical to the Q grade tube part |
Moisture level 1 and what it removes from the floor
A level 1 part needs no bake before reflow, which removes a step that most assembly lines handle badly. The step is not the bake itself, it is the record: a level 3 part has a 168 hour floor life, and every hour out of the dry cabinet has to be logged. A level 1 part has no clock, so the log disappears and with it a class of audit findings.
That is the practical value of the green code on this family. The nickel palladium gold finish is also the finish that survives multiple reflow passes without the intermetallic growth that tin lead finishes show, which matters on a board that is reflowed twice for a mixed assembly.
The finish does change the solder profile window slightly. Nickel palladium gold wets a little slower than tin, so a profile at the fast end of the tin window can leave a fillet that looks cold. The part is not the problem; the profile is. Check the paste and the soak before blaming the finish.
Electrical behaviour at the hot end
At 125 degrees the offset stays inside its 4 millivolt maximum, the bias current roughly doubles against its room temperature value, and the output saturation rises towards 1.5 volts at 50 milliamps. The supply current climbs towards its 6 milliamp ceiling on the positive rail.
None of those numbers is dramatic on its own. Together they narrow the operating margin of a threshold chain that was set up at 25 degrees, which is why a hot ambient part is worth a re-run of the threshold test rather than a paper substitution.
The one row that surprises people is the output leakage, which rises from 0.2 nanoamps at room temperature to 0.5 microamps over the window. On a 100 kilo ohm pull-up that is 50 millivolts of error when the output is meant to be off, and on a 1 megaohm pull-up it is half a volt. If the pull-up is large, the leakage is the parameter to check, not the offset.
Strobe, balance and the two pins that are not optional
The strobe pin needs a current of 3 to 5 milliamps and must not be shorted to ground. That is the sentence the data sheet repeats, and it is the sentence that field returns are made of. A 1 kilo ohm resistor from 5 volts is the standard drive.
The balance pins trim the offset at the calibration temperature. On a Q grade part the trim is usually done once at final test, and the residual drift over the 125 degree window is accepted. A trim at the hot end costs a chamber slot and buys about 1 millivolt.
The strobe resistor is worth a second look on a hot board. A 1 kiloohm resistor from a 5 volt rail passes about 4.3 milliamps at room temperature once the 0.7 volt drop of the internal diode is counted, and about 3.6 milliamps at 125 degrees. Both are inside the 3 to 5 milliamp window, which is why 1 kiloohm is the value that survives the whole range rather than the value that is correct at 25 degrees.
Both pins are assumed open in every electrical row. That is worth stating because a board that ties the strobe to a rail, or leaves the balance pins on a long trace, is measuring something the data sheet does not specify.
Where the green reel code is the right purchase
It is the right purchase wherever the board runs hot and the assembly line has a lead free process with no bake capability. Motor control boards, power supply secondaries, LED drivers, industrial sensors in sealed housings and under hood modules all fit.
It is the wrong purchase for a prototype, where a tube of 75 pieces is cheaper and a partial reel cannot be returned. It is also wrong where the customer's drawing names an automotive Q1 string, because this part does not carry that file.
Our date code management page covers how reel dates are recorded and traced, and the component lead time page covers what to do when the reel is on allocation and only tubes are on the shelf.
Allocation, substitution and the reel that is not on the shelf
Comparators of this age go short for dull reasons: a plating line is requalified, a reel is allocated to a large customer, or a distributor consolidates a warehouse. When the green reel is unavailable the honest options are three, and they are not equal.
The first is the plain reel, LM211QDR, which is the same die and the same grade with a different finish. Accepting it means accepting a tin based finish and a moisture level that may need a bake before reflow. On a lead free line that is a real difference rather than a paperwork one.
The second is the industrial grade in the same body. That moves the guarantee from 125 degrees down to 85, which is a change the customer has to approve if the board runs hot.
The third is a different family. It changes the pinout or the offset window, and that is a change that has to be evaluated rather than substituted.
Buying questions that come with this code
Buying questions that come with this code
Is the G4 part more expensive? Sometimes, by a few percent, and the difference is usually the finish rather than the grade. Ask for both codes in the same quote so the comparison is honest.
Can the Q grade be used at 85 degrees? Yes, with margin, and that is the usual reason a buyer keeps one string across two products.
Does the reel need a different feeder from the tube? Only in that the tube is hand loaded. The 12.4 millimetre tape is the standard width and needs nothing special.
What is printed on the reel label? The orderable code, the quantity, the date code, the lot and the moisture level. Photograph it before the reel is opened, because the label is the only record that ties the parts to the build.