Contact Us

LM211D

Brand: Texas Instruments
Texas Instruments LM211D is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211D — Power Management & Signal Chain | Superb Automation

LM211D

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211D from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211D: a single comparator with a strobe pin, in the tube carrier

LM211D is the single high speed differential comparator with the strobe and balance pins, eight pins in the SOIC body, supplied in the tube carrier at 75 pieces. It is the industrial temperature member of the LM111, LM211, LM311 family, guaranteed from minus 40 to plus 85 degrees, and it runs from a 5 volt logic supply or from plus and minus 15 volt rails without a change of external parts.

Two pins separate this part from a plain single comparator. The balance pins let an engineer null the input offset with a potentiometer instead of buying a tighter grade, and the strobe pin lets the output be forced off from logic, which is how a comparator is made to stop driving a bus without adding a gate. Both are analogue era features that still solve problems nothing else solves as cheaply.

The electrical centre of the part is different from the quad family. The offset is 3 millivolts maximum instead of 5, the response time is 165 nanoseconds instead of 1.3 microseconds, and the output sinks 50 milliamps instead of 16. This is a different animal with the same package outline.

LM211D as the vendor document publishes it

Figures are from the vendor document revision K dated March 2017, at plus or minus 15 volts unless the row says otherwise, with the balance and strobe pins open.

Channels1
Supply5 to 30 volts single, or plus or minus 15 volts split
Input offset voltage0.7 millivolts typical, 3 maximum at 25 degrees
Input offset voltage over temperature4 millivolts maximum, minus 40 to plus 85 degrees
Input offset current4 nanoamps typical, 10 maximum
Input offset current over temperature20 nanoamps maximum
Input bias current75 nanoamps typical, 100 maximum
Input bias current over temperature150 nanoamps maximum
Common mode range, lowerminus 14.5 volts minimum on a plus or minus 15 supply
Common mode range, upperplus 13 volts minimum, 13.8 typical
Large signal gain40 volts per millivolt minimum, 200 typical
Output low voltage0.75 volts typical, 1.5 maximum at 50 milliamps
Output leakage0.2 nanoamps at 25 degrees, 0.5 microamps over temperature
Supply current, positive rail5.1 milliamps typical, 6 maximum
Supply current, negative rail4.1 milliamps typical, 5 maximum
Response time, low to high115 nanoseconds
Response time, high to low165 nanoseconds
Output voltage rating50 volts
Output current rating50 milliamps
Strobe3 to 5 milliamps, current driven, never shorted to ground
Offset balancetwo pins, external potentiometer
Operating temperatureminus 40 to plus 85 degrees
Package8 pins, SOIC body D
Carriertube, 75 pieces

The strobe pin, and the difference between off and disabled

The strobe is a current driven input and the document repeats the point twice: it must not be shorted to ground, and it must be driven at 3 to 5 milliamps. Pulling the pin low with a resistor is not enough, because the pin is a current sink and a resistor that passes less than 3 milliamps leaves the comparator in an undefined state. A 1 kilo ohm resistor to a 5 volt logic output passes 5 milliamps and is the usual way to do it.

With the strobe active the output is forced off regardless of the input difference, which is what makes the part useful on a multiplexed bus and in a stacked threshold detector, where eight comparators share one wired or node and only one is allowed to drive at a time. It also lets a slow measurement chain gate the comparator so that a transient during a switching event never reaches the counter.

The strobe is not a shutdown. The input stage keeps running and the supply current does not fall, so a board that strobes the part hoping to save power saves nothing. On a battery instrument that matters, the standby saving has to come from the supply switch rather than from the strobe.

Offset null with two pins instead of a tighter grade

The two balance pins sit across the input stage, and a 100 kilo ohm potentiometer with its wiper to the positive rail is the circuit the vendor prints. That trims the offset to zero at the calibration temperature and, more usefully, lets an engineer measure the offset of each board during production and null it, which turns a 3 millivolt maximum part into a few tens of microvolts at room temperature.

The trimming does not remove the drift. A part trimmed at 25 degrees still moves 4 millivolts over minus 40 to plus 85, and the trim itself adds a temperature coefficient from the potentiometer, so a 100 parts per million per degree trim pot on a 2 millivolt trim contributes a few microvolts per degree. On a threshold that has to hold through a cold start, the trim is worth less than the grade.

Fifty milliamps of sink, and the load that comes with it

The output is a floating transistor, with the collector and the emitter both brought out, so the same part can sink 50 milliamps to ground or source current from a positive rail. That is a relay driver, a lamp driver, or a direct interface to an optocoupler without a transistor, and it is the row that keeps this part in circuits where a modern comparator would need a buffer.

The saturation voltage at that current is 0.75 volts typical and 1.5 maximum, which is 75 milliwatts in the package at the maximum. The eight pin SOIC has enough copper to carry it at 85 degrees, but not enough to carry it at 125, which is one reason the automotive member of the family is specified to 125 only in the Q code with its own thermal note.

Tube carrier, and the production move to a reel

The tube carrier at 75 pieces is the right carrier for a prototype and for a repair station. A line that places more than a few hundred boards a week moves to the reel code, which is the same die in the same body on a 2500 piece reel, and the move needs no board change and no software change.

LM211DSOIC D, 8 pins75 pieces, tubeminus 40 to plus 85 degrees
LM211DRSOIC D, 8 pins2500 pieces, 330 millimetre reelthe same die on the production carrier
LM211QDSOIC D, 8 pins75 pieces, tubeautomotive grade, minus 40 to plus 125 degrees
LM211QDRSOIC D, 8 pins2500 pieces, 330 millimetre reelautomotive grade on the reel

The addendum dated September 2026 prints only the LM211QDRG4 row for the LM211 codes. The plain D and DR rows are not printed there, so a production order should be confirmed against stock and date code rather than assumed from the catalogue entry. Our component obsolescence management page covers that check, and the last time buy planning page covers the quantity side when a code is on its way out.

Where the strobed single comparator belongs

It belongs in a peak detector, a zero crossing detector on a floating winding, a one shot threshold on a 24 volt industrial input, a relay driver from a sensor, and any board where a comparator has to be told to stop talking. It belongs in older instrument circuits that already have the plus and minus 15 volt rails, where the 50 volt output rating and the 50 milliamp sink remove two discrete parts per channel.

It is a poor fit on a 3.3 volt only board, where the 5 volt minimum supply and the 165 nanosecond response are wasted and a rail to rail part with a push pull output is smaller and cheaper. It is also a poor fit where the offset has to hold over minus 55 to plus 125, which is the LM111 grade and a different code.

Buying questions that come with this code

Is the strobe pin the same as a shutdown? No. The input stage and the output stage current continue, the output is only forced off, and the supply current stays at 5.1 milliamps.

Can the output pull down a 24 volt relay? It can sink 50 milliamps at 50 volts, so a 24 volt relay coil that draws under 40 milliamps can be driven directly with a freewheel diode across the coil.

Does the D suffix mean a different die from the older metal can part? No. The body and the pinout changed over the decades, and the electrical rows in the current document are the ones to work from for the SOIC body.