ISO7741FQDWRQ1
Product Specifications
ISO7741FQDWRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7741FQDWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7741FQDWRQ1: quad-channel reinforced digital isolator at 100 Mbps with default low outputs in a 16-pin wide SOIC
ISO7741FQDWRQ1 is four reinforced isolation channels at 100 Mbps, three forward and one reverse, defaulting low in a SOIC body of 16 pins. The 7741 arrangement is three forward and one reverse, the F suffix sets every output to default low, and the Q1 order code is the automotive qualified version. The wide body carries the 5000 V RMS rating and the 100 kV per microsecond typical transient immunity of the family.
Order code and package
| Order code | ISO7741FQDWRQ1 |
| Function | quad-channel reinforced digital isolator |
| Package | SOIC, 16 pins, DW wide body |
| Channels | four, three forward and one reverse |
| Data rate | 100 Mbps |
| Default output | low on every channel, set by the F suffix |
| Supply range | 2.25 V to 5.5 V on each side |
| Isolation | 5000 V RMS per UL 1577 |
| Surge capability | up to 12.8 kV |
| Transient immunity | 100 kV per microsecond typical |
| Barrier life | over 30 years at 1500 V RMS working voltage |
| Temperature range | minus 40 to plus 125 C |
| Qualification | automotive Q1 order code |
Electrical parameters that decide the application
| Barrier | silicon dioxide, reinforced |
| Esd | 8 kV IEC 61000-4-2 contact discharge across the barrier |
| Level translation | 2.25 V to 5.5 V on each side, any combination |
| Certifications | VDE 0884-17, UL 1577, IEC 61010-1, IEC 62368-1, IEC 60601-1, GB 4943.1 |
| Body options | wide SOIC and QSOP, plus wider creepage versions in the family |
| Output | CMOS push pull on every channel |
| Channel direction | three forward, one reverse, fixed |
| Channel count | four in this body |
Points to check before this part goes on a BOM
Default low on all four channels is what makes the F code the right choice for a drive interface. Before the controller has configured its pins, every enable and every gate signal on the isolated side is held inactive, and a power stage that starts into an unknown state is the fault this ordering choice prevents.
Three forward and one reverse matches a four wire peripheral interface. The reverse channel is the only path back, so a fault report that shares that line with the status word has to be readable within one frame, which is a firmware question that the part number decides the timing budget for.
The Q1 suffix does not change the isolation numbers. The 5000 V RMS rating, the 12.8 kV surge and the 30 year life projection belong to the family, and the automotive code adds qualification and the order code that the harness and the module file will ask for.
The family carries wider creepage versions for boards that need more than the standard package spacing. Those codes exist because creepage is a package property, and adding slots around a standard body does not produce a certified distance no matter how the drawing looks.
Where this order code fits
Traction and charger control interfaces, battery management boards and isolated gate signal bundles order this code where four signals cross one reinforced barrier and the safe state at power up is low. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is the default state per channel or per part? Per part. The F suffix sets all four outputs to default low; the plain code sets all four to default high.
Does it need an isolated supply for each side? Yes, one supply per side within the 2.25 V to 5.5 V range; the barrier isolates data only.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.