ISO7220MDR
Product Specifications
ISO7220MDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7220MDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7220MDR: dual-channel digital isolator at 150 Mbps with both channels in the same direction
ISO7220MDR is a two-channel digital isolator with both channels facing the same way at 150 Mbps in a SOIC body of 8 pins. The M suffix is the 150 Mbps grade of the ISO722x family, and the 7220 arrangement puts both channels in the same direction. Channel to channel skew is 1 nanosecond maximum and pulse width distortion is 1 nanosecond maximum, so a clock and its data can cross the barrier together without the pair drifting apart.
Order code and package
| Order code | ISO7220MDR |
| Function | dual-channel digital isolator |
| Package | SOIC, 8 pins, D body |
| Channels | two, both in the same direction |
| Signaling rate | 150 Mbps, the M grade |
| Channel to channel skew | 1 nanosecond maximum |
| Pulse width distortion | 1 nanosecond maximum |
| Jitter | 1 nanosecond typical at 150 Mbps |
| Transient immunity | 50 kV per microsecond typical |
| Supply | 2.8 V on the C grade, 3.3 V or 5 V on this one |
| ESD | 4 kV |
| Isolation | 2500 V RMS per UL 1577 |
| Temperature range | minus 40 to plus 125 C |
Electrical parameters that decide the application
| Barrier | silicon dioxide |
| Grade options | 1, 5, 25 and 150 Mbps across A, B, C and M suffixes |
| Direction options | 7220 both forward, 7221 one forward and one reverse |
| Output | CMOS, default state set by the input state at power up |
| Certifications | VDE 0884-17 conformity, UL 1577, IEC 61010-1, IEC 62368-1 |
| Propagation delay | specified in the switching table for each grade |
| Supply current | scales with rate, the M grade is the highest of the four |
| Channel count | two in this body |
Points to check before this part goes on a BOM
One nanosecond of channel to channel skew is the specification that makes this part usable for a clock and data pair. At 150 Mbps a bit is 6.7 nanoseconds, so a skew larger than a nanosecond would shift the sampling point of the pair by a sixth of a bit and eat the timing margin the receiver was counting on.
The 150 Mbps grade draws more supply current than the 25 Mbps grade of the same die. On a link that only needs 10 Mbps, ordering the M suffix buys headroom that is paid for on every board in the form of current, so the grade should follow the actual link rate rather than the biggest number in the table.
Both channels facing the same way means this body cannot carry a bidirectional pair. A UART or a request and acknowledge link needs the 7221 arrangement, and a board that fits the 7220 by mistake will have one dead direction that looks like a firmware fault.
The 8-pin body shares its pin out with the 7221, so the two arrangements are interchangeable on a board that was laid out for either. That is useful at the prototype stage and dangerous in production, where the wrong reel produces a working board with one direction missing.
Where this order code fits
Isolated digital links, differential clock distribution and high speed ADC interfaces order this code when two signals have to cross one barrier in the same direction. Boards comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What does the M suffix change? It sets the 150 Mbps signaling rate grade. The channel count, the pin out and the isolation rating stay the same across the family.
Can it isolate a 5 V signal from a 3.3 V receiver? Yes, the two sides can run from different supplies within the 2.8 V to 5 V range, with level translation in both directions.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.