Contact Us

ISO1212DBQR

Brand: Texas Instruments
Texas Instruments ISO1212DBQR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO1212DBQR — Power Management & Signal Chain | Superb Automation

ISO1212DBQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO1212DBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO1212DBQR: dual-channel isolated 24 V digital input receiver in a 16-pin SSOP

ISO1212DBQR is two isolated digital input receivers in one body, each with its own current limit in a SSOP body of 16 pins. The DBQ body holds two channels of the same receiver that the ISO1211 puts in an 8-pin package, so a 16 channel module needs eight of these instead of sixteen singles. Each channel has its own external resistor and its own current limit, and the pair shares only the logic side supply and the barrier.

Order code and package

Order codeISO1212DBQR
Functionisolated 24 V digital input receiver, two channels
PackageSSOP, 16 pins, DBQ body
StandardIEC 61131-2 Type 1, 2 and 3 for 24 V isolated inputs
Input range9 V to 300 V DC and AC with external resistors
Current limit2.2 to 2.47 milliamps per channel for Type 3, adjustable to 6.5 milliamps
Field side supplynone required, each channel draws from its input
Reverse polarityprotected to minus 60 V
Isolation2500 V RMS per UL 1577
Channelstwo, independent apart from the logic supply and ground
Supply2.25 V to 5.5 V on the logic side
Temperature rangeminus 40 to plus 125 C

Electrical parameters that decide the application

OutputCMOS logic level per channel
Channel to channel isolationshared barrier, the pair is one isolation group
CertificationsVDE 0884-17 conformity, UL 1577, IEC 60950-1, IEC 62368-1, IEC 61010-1, GB 4943.1
Diagnosticswire break detection per channel
Resistorone external resistor per channel, value set by field voltage
Power per channelabout 53 milliwatts in the resistor at 24 V and 2.2 milliamps
Filteringexternal capacitor with the current limit sets the response to contact bounce
Logic interfacedirect to 3.3 V and 5 V controllers

Points to check before this part goes on a BOM

Two channels in one 16-pin body share a barrier but not a current limit resistor. A module that puts 24 V and 110 V inputs on the same card has to size each resistor separately, and a shared resistor would put the two channels in series rather than in parallel.

The 16-pin SSOP pitch is tight for hand rework. A repair that lifts a pin on this body usually takes the channel with it, so a board that expects field returns should keep the single channel version as the spare rather than trying to reflow one half of a dual.

Wire break detection on each channel is what makes this part usable on safety inputs. The current loop is the diagnostic: no current through the resistor means an open field circuit, whether the cause is a broken wire or an unplugged connector.

The logic side draws its supply from the controller rail and the field side draws nothing, so the isolated DC to DC converter that an optocoupler bank needs disappears from the BOM. That converter is usually the tallest part on the board and the one with the shortest life, so removing it helps the mechanical envelope as much as the cost.

Where this order code fits

Multi-channel PLC input cards, remote IO blocks and machine safety panels order this code to halve the part count on a 24 V input bank. Boards comparing it with a neighbouring part start from our Medical Device Components page, and boards replacing a part that has gone end of life start from the BOM Consolidation page.

Questions buyers ask

Can the two channels sit on different field voltages? Yes, each channel has its own resistor and its own current limit, so 24 V and 110 V inputs can share one body.

Are the two channels isolated from each other? No. They share one barrier against the logic side; channel to channel there is no isolation rating.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.