Contact Us

ISO1176DWR

Brand: Texas Instruments
Texas Instruments ISO1176DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO1176DWR — Power Management & Signal Chain | Superb Automation

ISO1176DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO1176DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO1176DWR: isolated RS-485 Profibus transceiver rated to 40 Mbps

ISO1176DWR is an isolated RS-485 transceiver for Profibus networks in a SOIC body of 16 pins. It combines a galvanically isolated differential driver and receiver that meet EN 50170 and TIA/EIA-485-A, carrying up to 40 Mbps across a 4000 V peak barrier and supporting 160 nodes on one bus. The DWR order code is the wide body 16-pin SOIC on a reel.

Order code and package

Order codeISO1176DWR
Package16-pin wide body SOIC, DW
Packingtape and reel
Signalling rateup to 40 Mbps
Isolation4000 V peak per VDE 0884-17, 560 V peak working
Nodesup to 160 transceivers on one bus
Bus capacitance10 pF maximum
Failsafereceiver output defined on bus open, short and idle

Electrical parameters that decide the application

Differential outputexceeds 2.1 V into a 54 ohm load
Transient immunity50 kV per microsecond typical
Bus ESD16 kV human body model to GND2, 6 kV to GND1
Logic inputs3.3 V inputs, 5 V tolerant
Enableactive high driver enable with isolated ISODE output
Chip enablePV pin forces all outputs high impedance

Family variants and how they differ

ISO117640 Mbps, Profibus, 160 nodes, this order code
ISO308220 Mbps half duplex RS-485, 256 nodes
ISO308020 Mbps full duplex RS-485
ISO1176DWtube packing of the same part

Points to check before this part goes on a BOM

The Profibus qualification is the reason this part exists: EN 50170 fixes the driver output, the termination and the 1.5 Mbps to 12 Mbps rates that a process network runs at. The 40 Mbps ceiling is four times the fastest standard rate and is there for proprietary links on the same silicon, not because a Profibus segment will ever use it.

The 4000 V peak rating is a VDE 0884-17 figure with a 560 V peak working voltage, and it is not the same statement as a 2500 V RMS UL withstand. A customer comparing the ISO1176 against a 2500 V RMS part is comparing a peak repetitive rating with a one minute test, and the two numbers are not convertible by a factor of 1.4.

Bus loading is 10 pF maximum and 160 nodes, which is roughly twice the 32 node unit load limit of a classic 75176 style transceiver. That headroom is what allows a long process segment to keep its drivers without a repeater, and it disappears if the bus protection components add more capacitance than the transceiver does.

The ISODE pin outputs the enable state across the barrier, so the controller can read back whether the driver is actually on rather than assuming the enable command arrived. On a half duplex segment where a stuck driver takes the whole bus down, that feedback is the difference between a diagnosable fault and a silent one.

The PV pin forces every output to high impedance, which allows a module to be isolated from the bus without removing power. This is the pin to use for a hot swap arrangement, and it is not interchangeable with the driver enable because it also disables the receiver.

Transient immunity of 50 kV per microsecond typical is quoted for the barrier, not for the bus pins. A drive cabinet with a switching inverter couples the common mode transient into the cable, and the barrier rating is what keeps that current out of the controller ground while the bus pins themselves still see the full transient.

The bus pins are protected to 16 kV human body model against GND2 and 6 kV against GND1, and the asymmetry is deliberate: the cable side carries the surge, the logic side does not. A protection network added on the logic side does nothing for the rating that matters.

Segment termination for Profibus is a pair of 390 ohm bias resistors and a 220 ohm terminator at each end, and the bias network draws current continuously. On an isolated segment that current comes from the isolated supply, so a segment with 32 nodes and two terminators has a standing load that the transformer driver has to cover at all times, not only while transmitting.

The 40 Mbps rate is not usable across a long Profibus cable. At that rate the bit time is 25 ns and the cable delay alone exceeds it after a few tens of metres, so the rate belongs to short backplane links while the process segment runs at 1.5 Mbps to 12 Mbps.

Termination resistors on an isolated Profibus segment have to be powered from the isolated side, and the bias network draws current even when the bus is idle. A 390 ohm pair across 5 V draws about 12 mA, which is several times the transceiver's own supply current, so the isolated rail is sized by the termination and not by the part. Removing the terminators to save current leaves the segment without a defined idle level.

Where this order code fits

It is used on Profibus DP segments, isolated RS-485 process networks, drive and motor control links, building automation buses and any multipoint link that crosses a ground barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is it half duplex or full duplex? Half duplex, with a driver enable and a receiver enable. The isolated ISODE output reports the driver state to the controller side.

Can 3.3 V logic drive it directly? Yes. The logic inputs are 3.3 V devices that tolerate 5 V, so a 3.3 V controller connects without a translator.

Does it include termination? No. The 120 ohm terminators and the failsafe bias resistors are external, and their capacitance counts against the 10 pF bus figure.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.