Contact Us

TPS2051CDBVR

Brand: Texas Instruments
Texas Instruments TPS2051CDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS2051CDBVR — Power Management & Signal Chain | Superb Automation

TPS2051CDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS2051CDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS2051CDBVR: 0.5 A fixed limit power switch with reverse current blocking

TPS2051CDBVR is a single channel fixed current limit power switch with reverse current blocking in a SOT-23 body of 5 pins. It is the later generation of the 0.5 A switch, with a plus or minus 20 percent limit and a body that blocks current from output to input.

Order code and package

Order codeTPS2051CDBVR, DBV package, 3000 pieces on a large reel
BodySOT-23, 2.90 mm by 1.60 mm, five leads
MarkingPYJI on the DBV body
EnableActive high, 2 V rising threshold
Family position0.5 A member of the TPS20xxC group, shares the silicon with the 1 A and 2 A members

Electrical parameters that decide the application

Input range4.5 V to 5.5 V for the specified limits, with the wider 2.7 V operation carried by the B family
On resistance97 mOhm typical and 110 mOhm maximum at 25 C, 96 mOhm typical and 130 mOhm maximum from -40 C to 85 C
Current limit0.67 A minimum, 0.85 A typical, 1.01 A maximum for the 0.5 A rated output
Overcurrent response2 us typical, fast enough that the upstream 5 V supply does not collapse
Quiescent current0.05 mA typical and 2 mA maximum enabled, 0.01 mA typical and 1 mA maximum disabled
Reverse leakage1 uA maximum with the output above the input and the device off
ESD8 kV contact and 15 kV air gap under IEC 61000-4-2, which is what a connector facing part needs

Family variants and how they differ

TPS2041CSame die with an active low enable
TPS2069C1 A rated member, same body and pin out, limit scaled to the higher current
TPS2065C0.5 A with a different flag behaviour and no reverse blocking claim
TPS2051BPrevious generation, 0.75 A to 1.25 A limit window and no reverse blocking specification
TPS2553Adjustable limit and a latched version, for a port that must stay off after a fault

Points to check before this part goes on a BOM

The limit window is the reason to specify this part instead of the older B. At 0.67 A to 1.01 A the spread is plus or minus 20 percent around 0.85 A, against 0.75 A to 1.25 A on the B. A port that must deliver 0.5 A and must not deliver more than 1 A to a fault now has a part whose maximum limit sits exactly at that ceiling, and the upstream supply and the connector are sized against 1.01 A rather than 1.25 A.

On resistance is quoted at 25 C and again over the industrial range. The 97 mOhm typical becomes 96 mOhm typical at the cold end and 130 mOhm maximum over temperature, so the drop at 0.5 A is 48.5 mV typical and 65 mV at the limit. The 110 mOhm figure applies at 25 C only, and a thermal calculation that uses it understates the dissipation by 18 percent at the temperature extremes.

Reverse current blocking is stated as 1 uA maximum leakage with the output held above the input while the switch is off. This is the case where a downstream rail is back fed by a battery or a second supply during a brownout, and the blocking keeps the fault from propagating upstream. It is a specification, not a claim about the body diode, so it holds only while the device is disabled and the enable pin is held low.

The IEC 61000-4-2 figures of 8 kV contact and 15 kV air gap are the reason this part can sit directly behind a user accessible connector. They describe the device surviving the strike, not the load being protected: the residual current still reaches the far side of the switch through the capacitance of the body, and the load needs its own clamp if it is sensitive.

Response time of 2 us is what keeps a 5 V backplane alive when a downstream board shorts. The limit is reached in constant current mode rather than by a hard shutoff, so the supply sees a known 1.01 A maximum for the 2 us and then whatever the thermal circuit allows. The upstream regulator must be able to hold its output for that interval, which on a 5 V rail with a few hundred microfarads of bulk is not a constraint.

Quiescent current of 0.05 mA typical enabled and 0.01 mA typical disabled is small but not zero. The 2 mA maximum enabled figure is what a standby budget has to use, because the maximum is three orders of magnitude above the typical. At 2 mA the part alone costs 17.5 mAh over a year, which is still below a coin cell self discharge but no longer negligible in a product that sleeps for months.

The 4.5 V to 5.5 V specified range is narrower than the 2.7 V to 5.5 V operating range carried by the B family. The silicon works below 4.5 V, but the electrical table is written for the 5 V band, so the resistance and limit numbers do not apply to a 3.3 V rail. A 3.3 V port should be specified from the B family table or from a member whose table covers the lower rail.

Body marking matters at incoming inspection. The DBV body carries PYJI while the 1 A member carries a different code, and both are five lead SOT-23 in the same reel format. A mixed reel is not detectable from the package outline, so the inspection plan should read the marking and the reel label rather than sample the outline.

The A and G4 suffixes on the orderable list are packing and finish variants, not silicon revisions. TPS2051CDBVR.A and TPS2051CDBVRG4 carry the same die and the same electrical table, and the difference is the reel labelling and the lead finish combination. A bill of materials that names the plain code and receives a G4 part has received the same switch. What is not the same is the marking on the body, so an inspection that compares the marking against a photograph of the plain part will reject a valid shipment. The suffix has to be read against the addendum rather than against the body.

Where this order code fits

This is the part for a 5 V USB port, a docking bay or a hot plug card where the limit has to be tight enough for the connector rating and the upstream supply, and where a back fed rail during a brownout must not push current into the main 5 V plane. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is it a drop in for the TPS2051B? The body and pin out match, and the enable polarity matches, but the limit window and the specified input range differ, so the fault current and the 3.3 V behaviour have to be rechecked.

What is the difference from the -2 suffix parts? The suffix marks the output discharge option, which pulls the output down when the switch turns off; this order code carries the plain body.

Will it survive a cable short? It limits at 1.01 A maximum and relies on thermal shutdown for a sustained short, so the survival claim is about the device and not about the cable.

Does the flag need a pull up to 5 V? Yes, it is open drain and can be pulled to any rail within the absolute maximum, so 3.3 V logic is fine as long as the pin rating is respected.

What does the IEC 61000-4-2 rating cover? The device surviving an 8 kV contact or 15 kV air discharge on the pins, not the load behind it being protected from the residual current.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.