Contact Us

TPS51396ARJER

Brand: Texas Instruments
Texas Instruments TPS51396ARJER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51396ARJER — Power Management & Signal Chain | Superb Automation

TPS51396ARJER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51396ARJER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51396ARJER: 4.5 V to 24 V, 8 A synchronous buck with ultra low quiescent mode

TPS51396ARJER is a synchronous buck converter with the FETs inside the package in a HotRod VQFN body of 20 pins. It converts up to 24 V down to as low as 0.6 V at 8 A, and its light load mode is built for a product that has to sit in standby for months.

Order code and package

Order codeTPS51396ARJER, RJE package, 3000 pieces on a reel
BodyHotRod VQFN, 3.00 mm by 3.00 mm, twenty pins
Switch resistance19.5 mOhm high side and 9.5 mOhm low side, integrated
ControlD-CAP3, no external compensation
Soft start1.3 ms internal, longer with a capacitor on the SS pin

Electrical parameters that decide the application

Input range4.5 V to 24 V operating
Output range0.6 V to 7 V, 8 A continuous
Reference accuracy1 per cent feedback accuracy at 25 C
Switching frequency600 kHz, 800 kHz or 1 MHz selected by the MODE pin
Light load modesEco-Mode for efficiency, out of audio mode that stays above 25 kHz at no load
ProtectionCycle by cycle overcurrent, latched overvoltage and undervoltage, non latched overtemperature and input lockout
DischargeBuilt in output discharge on the SW node when disabled

Family variants and how they differ

MODE at one levelEco-Mode, pulse skipping at light load for the best standby efficiency
MODE at another levelOut of audio mode, switching held above 25 kHz so the converter does not sing in a quiet product
MODE at the third levelSets the 800 kHz or 1 MHz option, trading switching loss for smaller magnetics
SS pin floating1.3 ms internal soft start
SS pin with a capacitorLonger ramp for a large output bank or a sequenced rail

Points to check before this part goes on a BOM

The two switch resistances are what decide efficiency at 8 A. Conduction loss is 8 squared times 19.5 mOhm times the duty cycle plus 8 squared times 9.5 mOhm times the rest, which at 24 V to 5 V is 0.31 W in the high side FET and 0.46 W in the low side, or 0.77 W before switching loss. In a 3 mm by 3 mm body that is the number that sets the copper under the part.

The 24 V input limit and the 0.6 V output floor are the two ends of the duty cycle problem. At 24 V in and 0.6 V out the duty is 2.5 per cent, and at 600 kHz that is 42 ns of on time, which is at the edge of what the internal driver can hold. A 1 MHz setting makes it 25 ns, so a very low output voltage from a high input is a place where the switching frequency has to go down, not up.

ULQ mode is the reason the part exists in battery products. It keeps the bias current low and allows large duty operation, so a converter that has to hold a rail alive through a long standby can do it without a second always on regulator. The honest caveat is that the quiescent figure applies to one mode, and forced PWM at 1 MHz does not have it.

Out of audio mode is a mechanical requirement disguised as an electrical one. A converter that pulse skips at no load can drop into the audio band and make a ceramic capacitor or an inductor sing, which is unacceptable in a set top box in a quiet room. Holding the switching above 25 kHz costs standby efficiency and removes the noise, and the MODE pin chooses between the two.

D-CAP3 removes the compensation network but not the output capacitor requirement. The loop is stabilised by the output capacitor ESR and value, so moving from a 470 uF polymer to a 22 uF ceramic changes the transient response and the phase margin, and the data sheet values are the place to start rather than a rule that any capacitor works.

The 1 per cent feedback accuracy at 25 C is a room temperature number. Over the full range the divider and the reference drift add to it, so a rail that must hold 1 per cent at 105 C needs a divider with 0.1 per cent resistors and a check of the reference drift, not the headline figure.

The overvoltage and undervoltage protections latch, while overtemperature and input lockout do not. That means a transient that pushes the output over the OVP threshold takes the rail down until the enable is cycled, which is the right behaviour for a load that must not see an overvoltage, and the wrong one for a load that would rather ride through a glitch.

The built in discharge turns the low side FET on when the part is disabled, so the output falls to zero in milliseconds instead of leaking down through the load. On a rail that is re-enabled quickly, that is what stops the output from starting into a pre-charged state and the inrush from doubling.

The inductor is chosen from the ripple at the chosen frequency, and the three frequency options change it by less than a factor of two. At 600 kHz and 12 V to 5 V, 2.2 uH gives about 1.6 A of ripple at 8 A, which is 20 per cent; at 1 MHz the same inductor gives 1 A and a smaller part would do. The saving in board area is real and the loss in efficiency at 24 V input is also real, because the switching loss rises with frequency.

At 8 A the 3 mm body has to pass 0.77 W of conduction loss plus switching loss through its pads. The thermal resistance of the HotRod package is good but not free, and a four layer board with a solid ground plane under the part runs cooler than a two layer board with the same copper area. A 60 C ambient with no airflow is the case that decides whether the part meets its rating.

Where this order code fits

The part suits a 12 V or 19 V input rail in a set top box, a monitor, a point of load converter in networking gear, or any product where standby current is a specification rather than an afterthought. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it run from 24 V continuously? Yes, 24 V is the operating limit. There is no margin for a 24 V rail at plus ten per cent, so a nominal 24 V bus needs a part rated above it.

What sets the current limit? It is cycle by cycle and internal to the part, with the threshold tied to the low side FET current. There is no external sense resistor.

Does it need a bootstrap capacitor? Yes, one capacitor from VBST to SW is the only external part the driver needs, and it is charged by an internal switch.

How low can the output go at 1 MHz? The on time floor is what limits it. At 1 MHz, 0.6 V out of 24 V is 25 ns of on time, which the driver cannot hold, so the frequency has to come down for a very low output.

Can the frequency be changed on a running board? Only by changing the MODE pin level, which is a hardware strap. It is not a register setting, so the choice is made at assembly or by a GPIO that is set before the rail is enabled.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.