Contact Us

TPS51215ARUKR

Brand: Texas Instruments
Texas Instruments TPS51215ARUKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51215ARUKR — Power Management & Signal Chain | Superb Automation

TPS51215ARUKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51215ARUKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51215ARUKR: Single phase D-CAP2 buck controller with a 2 bit set point selector

TPS51215ARUKR is a single phase synchronous buck controller with four stored output set points in a WQFN body of 20 pins. It regulates one rail from 0.5 V to 2 V out of an input up to 28 V, and two logic pins pick one of four set points while the rail is running.

Order code and package

Order codeTPS51215ARUKR, RUK package, 3000 pieces on a reel
BodyWQFN, 3.00 mm by 3.00 mm, twenty pins plus thermal pad
Set pointsFour, one of them 0 V, selected by VID0 and VID1
Reference2 V at 300 uA, 0.8 per cent tolerance
Switching frequency600 kHz fixed in D-CAP2 mode

Electrical parameters that decide the application

Conversion input3 V to 28 V, with a separate 5 V bias rail from 4.5 V to 5.25 V
Output range0.5 V to 2.0 V, plus a 0 V set point for a rail that must be off
Current senseLow side RDS(on), the TRIP pin sources 10 uA with a 4700 ppm per C temperature coefficient
Current limitVOCL equals VTRIP divided by 8, and VTRIP is capped at 3 V, so the sense threshold is 375 mV at most
Supply current610 uA running, 250 uA standby, 1 uA in shutdown
Soft start and slew4.5 uA into the SS capacitor, 45 uA into the SLEW capacitor
Bias lockout4.4 V rising, 4.0 V falling, 400 mV of hysteresis
Thermal resistance94.1 C/W junction to ambient in the RUK body

What each strapping pin changes

V0 to V3One resistor per set point, each pin programmed independently to ground
VID0 and VID1Select which of the four set points is active, and 00 selects 0 V
SLEWSets the transition time between set points, 45 uA charging an external capacitor
TRIPSets the current limit through the low side RDS(on), VTRIP divided by 8
VSNS and GSNSDifferential sense pair, closed with 10 Ohm to the load when remote sense is used

Points to check before this part goes on a BOM

The 2 bit input is a mode switch, not a reference. Three set points come from resistors and the fourth is 0 V, so a rail can be commanded off without gating the enable pin, and a transition between set points runs at the slew rate set by the SLEW capacitor rather than at the loop bandwidth.

The 4700 ppm per C coefficient on the TRIP current is there to track the low side FET. Copper and silicon on resistance rise by roughly 4000 ppm per C, so a fixed sense threshold would let the real current limit drift upward with temperature, while this arrangement holds the current trip roughly constant from 25 C to 125 C.

The current limit threshold is VTRIP divided by 8 with VTRIP capped at 3 V, which means the largest sense voltage is 375 mV. Across a 2 mOhm low side FET that is 187 A, so in practice the resistor on TRIP sets a number far below the cap and the FET, not the controller, is what has to survive the trip.

D-CAP2 with all ceramic output capacitors means no compensation network and no external integrator for stability, but DC accuracy still comes from the integrator capacitor. With POSCAP or polymer output the same pin sets the load regulation, and leaving it out gives a rail that is stable and a few per cent off at load.

The 94.1 C/W thermal resistance in a 3 mm by 3 mm body is the practical limit on gate drive. Driving two FETs with 30 nC each at 600 kHz is 36 mW of driver loss inside the controller plus the quiescent 610 uA, which is about 3 mW, so the junction sits well under the limit at 85 C ambient but not at 105 C with larger FETs.

A 5 V bias rail is required and cannot be derived from the 28 V input inside the part. Boards that assume the controller runs from the conversion input alone will find the drivers dead, and the 4.4 V rising lockout means the bias has to be up before the enable is released.

The 0 V set point is a real output state, not a shutdown state. The controller keeps switching with a zero reference, which discharges the output through the low side FET instead of leaving it floating, and that is the difference between a rail that comes back cleanly and one that restarts into a pre-charged output.

Remote sense through VSNS and GSNS is what makes the 0.8 per cent reference worth having. Without it, 20 mV of drop in the copper at 10 A eats the whole tolerance, so a rail that must hold 1 per cent at the load has to bring both sense lines out to the socket.

The 600 kHz frequency puts a floor on the on time. At 28 V in and 0.5 V out the on time is 18 ns, which no controller in this class can hold, so the practical minimum output from a 28 V input is around 1 V. Boards that need 0.5 V from 28 V use a two stage conversion, and this part is the second stage from a 5 V or 3.3 V rail.

The transition between set points is a controlled ramp, not a step, and the SLEW capacitor is what sets it. At 45 uA into 10 nF the pin moves at 4.5 V/ms, and with the loop following that ramp the output changes at the same rate. A load that cannot tolerate a supply change faster than 1 V/ms needs a larger capacitor, and one that treats the rail as static needs to know the transition happens at all.

The VID pins take both 1 V and 3.3 V logic, which is why the part can sit on the same board as both a low voltage microcontroller and a 3.3 V system controller. What the pins are not is tolerant of a floating input: an unloaded pin reads as a logic high, so a board that leaves one unconnected selects a set point nobody intended, and the four states make that mistake look like a working rail at the wrong voltage.

Where this order code fits

The part suits a notebook or industrial PC rail that has to switch between a low power state and a full power state while staying in regulation, and any point of load converter that needs a hardware selected voltage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the four set points be any voltage? Any value between 0.5 V and 2.0 V, one per resistor on V0 to V3, with 00 reserved for the 0 V state.

Does it need a compensation network? No. D-CAP2 is stable with ceramic output capacitors, and the only tuning part is the integrator capacitor that sets DC accuracy.

What happens if the 5 V bias is missing? The part stays in lockout below 4.4 V and the drivers do not switch, so the rail does not come up even with the conversion input present.

Is the current limit adjustable while running? The TRIP pin is a resistor to ground, so it is fixed at assembly. Changing it in circuit needs a different resistor, not a register write.

Is the set point change allowed while the rail is loaded? Yes, the SLEW capacitor sets a controlled ramp and the loop follows it. The load sees a supply change, so the ramp rate is a system requirement rather than a converter one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.