INA592IDT
Product Specifications
INA592IDT
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA592IDT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA592IDT: the same difference amplifier on a 250 piece reel
INA592IDT is the precision difference amplifier in the 8 pin SOIC on a 250 piece small reel, the carrier for a first article and a bench build. The gain is 0.5 or 2 by connection, the gain error is 0.01 per cent typical, the offset is 14 microvolts typical and the drift is 0.7 microvolts per degree.
The small reel is the practical way to evaluate the part before committing to the 3000 piece reel of the R code. It also suits a low volume instrument that builds a few hundred units a year, where a reel would outlive the product. The body, the pinout and the trimmed network are identical, so a board proved on the small reel moves to the large one without a change.
INA592IDT as the vendor document publishes it
| Gain | 0.5 V/V or 2 V/V, set by the input connection |
| Gain error | 0.01 per cent typical, 0.03 per cent maximum |
| Gain drift | 0.2 ppm per degree typical, 0.5 ppm per degree maximum |
| Offset voltage referred to the output | 14 microvolts typical, 40 microvolts maximum |
| Offset drift | 0.7 microvolts per degree typical, 2 microvolts per degree maximum |
| Common mode rejection | 88 dB minimum, 100 dB typical |
| Voltage noise at 1 kHz | 18 nanovolts per root hertz |
| Gain bandwidth | 2 MHz |
| Slew rate | 18 volts per microsecond |
| Quiescent current | 1.1 milliamps per amplifier |
| Capacitive load drive | 500 picofarads |
| Supply range | 4.5 to 36 volts single, plus or minus 2.25 to plus or minus 18 volts dual |
| Input common mode | extends to the negative supply |
| Temperature range | minus 40 to plus 125 degrees |
| Body | SOIC, 8 pin, D, 4.90 by 3.91 millimetres |
| Vendor status | active, 250 piece small reel |
| Catalogue code | INA592IDT |
| Vendor string | INA592IDT |
| Lead finish | NIPDAU |
| Moisture level | level 2, 260 degrees, one year floor life |
One point one milliamp per amplifier
The quiescent current of INA592IDT is 1.1 milliamps per amplifier, which is low for a part with 2 MHz of bandwidth and 18 volts per microsecond of slew rate, and it is the row that makes the part usable in a multichannel instrument. Four channels of difference amplification plus a reference cost under 5 milliamps, which a 24 volt industrial supply does not notice.
The supply range is the other half of the same story: 4.5 to 36 volts single, or plus or minus 2.25 to plus or minus 18 volts dual, with a specified temperature range of minus 40 to plus 125 degrees. A 4.5 volt floor means the part runs from a 5 volt rail and from a 24 volt rail with no change, and the 36 volt ceiling means a 24 volt rail with a 10 per cent tolerance stays inside the absolute maximum with the usual margin.
Where an integrated difference amplifier belongs
INA592IDT belongs on a current shunt in a motor drive or a battery system, on a plus or minus 10 volt industrial signal that has to be scaled into a converter, on a bridge amplifier where the reference has to move with the supply, and on any channel where the ratio has to hold over temperature without a calibration step.
It stops where the common mode is far above the supply, because the input range extends down to the negative rail rather than up; where the gain has to be programmable, because the two gains are wired rather than selected; and where the signal is below a millivolt, because the 18 nanovolts per root hertz and the 40 microvolt offset belong to a 10 millivolt channel rather than to a shunt on a milliamp range. Our amplifier cross reference page covers the instrumentation amplifiers that take the sub millivolt case, and the BOM scrubbing page covers the two gain connections against the bill of materials.
A gain of one half or two, wired by the pins
INA592IDT is a difference amplifier with the resistor network inside the package, and the two published gains come from how the inputs are connected rather than from an external pair: 0.5 V/V in one connection and 2 V/V in the other. The network is trimmed as a unit, which is why the gain error is 0.01 per cent typical and 0.03 maximum and the gain drift is 0.2 ppm per degree typical and 0.5 maximum.
That tracking is the whole point of the part. A discrete difference amplifier built from four resistors is only as good as their matching, and a 0.1 per cent pair with 25 ppm per degree drifts far more than 0.5 ppm. Where a channel has to hold a ratio over temperature rather than only at 25 degrees, the integrated network removes the largest term in the error budget, and it removes it without a calibration step.
Eighty eight decibels of rejection from a resistor network
The common mode rejection of INA592IDT is 88 dB minimum and 100 dB typical, and it is set by the same trimmed network that sets the gain. That is the second thing the integration buys: a discrete network with four resistors has a rejection that depends on the match of two ratios, and the rejection degrades as soon as one resistor moves.
The other half of the rejection story is the input range. The internal amplifier has a common mode range that extends to the negative supply, so a channel that measures a shunt sitting at ground, or a sensor whose common mode passes through ground, does not clip the input stage. A 4.5 to 36 volt single supply covers a 5 volt rail and a 24 volt rail with the same part, and the dual supply range of plus or minus 2.25 to plus or minus 18 volts covers a bipolar analogue front end.
Forty microvolts at the output, and the drift that follows
The offset of INA592IDT is 14 microvolts typical and 40 microvolts maximum referred to the output, with a drift of 0.7 microvolts per degree typical and 2 maximum. The reference to the output matters: at a gain of 0.5 the input referred figure is 80 microvolts, and at a gain of 2 it is 20.
Over the 165 degree window the drift of 2 microvolts per degree is 330 microvolts at the output, which is eight times the maximum offset itself. That is the row a precision channel has to budget, and it is the reason the part is bought for its low offset drift rather than only for its gain accuracy. The noise of 18 nanovolts per root hertz at 1 kHz sits between the two: smaller than the drift over a wide temperature swing, larger than the offset at room.
Two megahertz, eighteen volts per microsecond, five hundred picofarads
The gain bandwidth of INA592IDT is 2 MHz with a slew rate of 18 volts per microsecond, and the output drives 500 picofarads without a series resistor. That combination is what makes the part usable as a driver rather than only as a front end: a 24 bit converter with a switched input capacitor needs an amplifier that settles a large step quickly, and 18 volts per microsecond on a 10 volt step is the number that decides the acquisition window.
The capacitive load row is the one that saves a board turn. A difference amplifier driving a cable or a long trace sees hundreds of picofarads, and most parts with this bandwidth need an isolation resistor that costs a pole. With 500 picofarads specified, the resistor can be left out where the load is known, and the settling time stays as published instead of moving by a factor of two.
Two hundred and fifty pieces covers the evaluation and the first build. Our BOM scrubbing page covers the two gain connections against the bill of materials, and the vendor consolidation page covers the move to the reel.
Is the T code the same part as the R code? Yes, one body and one document; the T is 250 pieces and the R is 3000.
Does the small reel change the moisture level? No, level 2 with a one year floor life on both.