INA4180A2IPWR
Product Specifications
INA4180A2IPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA4180A2IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA4180A2IPWR: the gain of fifty member, and the one grade of the four that the vendor has stopped building
INA4180A2IPWR is the gain of fifty member of the four channel current sense family in the fourteen pin TSSOP. The electrical rows are shared with the rest of the family: 26 volts of common mode, 500 microvolts of offset at a 12 volt common mode, 84 decibels of rejection and 2 volts per microsecond of slew rate.
The status line is different. The vendor addendum prints this code as obsolete while the 20, 100 and 200 volts per volt members of the same family stay in production, which makes the gain of fifty the one option with a finite remaining supply. A board specified at a gain of 50 either buys what is left or moves to a gain of 20 or 100 and rescales the shunt, and both routes are covered below.
INA4180A2IPWR as the vendor document publishes it
| Channels | 4 |
| Gain options | 20, 50, 100 and 200 volts per volt, fixed by an internal network |
| Common mode range | 0.2 volts below ground to 26 volts |
| Supply | 2.7 to 5.5 volts |
| Offset at zero volts of common mode | plus or minus 25 microvolts typical, plus or minus 150 maximum |
| Offset at 12 volts of common mode | plus or minus 100 microvolts typical, plus or minus 500 maximum |
| Offset drift | 0.2 microvolts per degree typical, 1 maximum |
| Common mode rejection | 84 decibels minimum, 100 typical |
| Power supply rejection | 80 microvolts per volt |
| Gain error | 0.1 per cent typical, 1 per cent maximum |
| Gain error drift | 20 parts per million per degree |
| Nonlinearity | 0.01 per cent between 0.5 volts and half a volt below the supply |
| Bandwidth | 350, 210, 150 and 105 kilohertz for the four gains |
| Slew rate | 2 volts per microsecond |
| Voltage noise | 40 nanovolts per root hertz |
| Quiescent current | 900 microamps typical, 1 milliamp maximum for four channels |
| Temperature range | minus 40 to plus 125 degrees |
| Package | 14 pins, TSSOP body PW |
| Catalogue code | INA4180A2IPWR |
| Vendor status | obsolete at the vendor |
| Gain | 50 volts per volt |
| Package | 14 pins, TSSOP body PW |
| Replacement path | gain of 20 or 100 with a rescaled shunt |
Offset at zero volts of common mode, and again at twelve
The offset of INA4180A2IPWR is quoted twice, because the answer depends on where the inputs sit. At a common mode of zero volts the row reads plus or minus 25 microvolts typical and plus or minus 150 microvolts maximum. At a common mode of 12 volts the same row reads plus or minus 100 microvolts typical and plus or minus 500 microvolts maximum.
The drift is 0.2 microvolts per degree typical and 1 microvolt per degree maximum across the minus 40 to plus 125 degree range. On a 10 milliohm shunt at 5 amps the sense voltage is 50 millivolts, so 500 microvolts is one per cent of reading, and that is the number to put against the tolerance of the shunt itself before choosing a gain.
Four current sense channels in one fourteen pin TSSOP
INA4180A2IPWR is one quarter of the INAx180 family, a voltage output current sense amplifier with a fixed gain, packaged four to a fourteen pin TSSOP. The four gain options are 20, 50, 100 and 200 volts per volt, and the gain is set by a matched resistor network inside the package rather than by an external pair, so the gain error and the drift come from one trimmed block.
The common mode window runs from 0.2 volts below ground to 26 volts, independent of the 2.7 to 5.5 volt supply, which is what allows the part to sit on the high side of a 24 volt rail and still drive a converter that runs at 3.3 volts. All four channels share the supply pins but not the inputs, so four separate shunts can be read through one package.
Gain error of one per cent, and what it costs at ten millivolts
The gain error of INA4180A2IPWR is 0.1 per cent typical and 1 per cent maximum, with 20 parts per million per degree of drift and a nonlinearity of 0.01 per cent between 0.5 volts and half a volt below the supply. The power supply rejection is 80 microvolts per volt, so a 100 millivolt supply step moves the output by 8 microvolts referred to the input.
A one per cent gain error on a 10 millivolt sense signal is 100 microvolts, which is small against the 500 microvolt offset at a 12 volt common mode but larger than the offset at zero common mode. That ordering is why the family is specified with both common mode cases rather than one, and why a two point calibration at the working common mode recovers most of the error.
Nine hundred microamps for four channels, and the carrier rows
The quiescent current of INA4180A2IPWR is 900 microamps typical and 1 milliamp maximum at 25 degrees, and it is quoted for the whole package rather than for one channel, because the four amplifiers share one bias block. Over the full temperature range the maximum rises to the same 1 milliamp figure, so the supply budget does not change with the ambient.
The package is the fourteen pin TSSOP, and the reel code carries the R suffix while the tube code carries a T. The body is the same one used by the dual and single members of the family, so the land pattern for four channels is the only one a board needs if the channel count may grow.
Three hundred and fifty kilohertz at a gain of twenty, and the three lower numbers
The bandwidth of INA4180A2IPWR falls as the gain rises, because the gain is set by the same internal network. The A1 device at a gain of 20 holds 350 kilohertz, the A2 at 50 holds 210 kilohertz, the A3 at 100 holds 150 kilohertz and the A4 at 200 holds 105 kilohertz, all measured at a 10 millivolt sense voltage.
The slew rate is 2 volts per microsecond on all four, and the voltage noise density is 40 nanovolts per root hertz. A 20 kilohertz switching supply measured through a 200 volts per volt channel therefore has five times the headroom it needs, while a 100 kilohertz current loop on the same channel is already at the edge of the small signal response.
Where four current sense channels belong
INA4180A2IPWR belongs in a three phase motor drive, where three shunts read the phase currents and the fourth reads the bus return; in a quad hot swap card, where each rail has its own shunt; in a power over ethernet switch, where four ports are monitored through one package; and in a battery tester that cycles four cells at once.
The 26 volt common mode, the fixed gains and the 900 microamps are the three rows that fit those cases. What the part does not do is measure current in both directions, because the output is referred to ground rather than to a mid supply reference, and that is the difference between this family and the bidirectional one beside it.
What the four channels do not share
The four channels of this package share the supply pins, the bias block and the ground return, and they share nothing else. Each has its own input pair and its own output, so a fault on one shunt does not move the other three, and the four outputs can be read by four separate converter channels or by one multiplexed converter.
What they do share is the ground return current, and that is the coupling path a four channel part introduces where four single parts would not. The return from four outputs at 1 milliamp each is small, but the return from four shunts on the same copper is not, so the star point of the four shunt returns is the one place on the board that decides whether the channel to channel separation is real.
An obsolete gain option is a last time buy question before it is an electrical one. Our last time buy planning page covers the quantity, and the pin to pin cross reference page covers the move to another gain.
Can the gain of fifty be replaced by another member of the family? Yes, with a shunt change. A gain of 20 with two and a half times the shunt resistance, or a gain of 100 with two fifths of it, gives the same output at the same current, and the offset moves with the gain rather than the shunt.
Is the package the same on all four gains? Yes. All four are the fourteen pin TSSOP with the same pinout, so the board does not change when the gain does.