Contact Us

INA350ABSIDDFR

Brand: Texas Instruments
Texas Instruments INA350ABSIDDFR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA350ABSIDDFR — Power Management & Signal Chain | Superb Automation

INA350ABSIDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA350ABSIDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA350ABSIDDFR: 10 or 20 V/V instrumentation amplifier in a 8-pin SOT-23 thin

INA350ABSIDDFR is a small instrumentation amplifier with a pin selectable gain in a SOT-23 thin body of 8 pins. Two gain options in one body: a pin strap selects 10 or 20 V/V on the ABS version, and the sister CDS version offers 30 or 50. The point of the order code is the footprint, 4.64 square millimetres in the SOT-23 thin body, built around 10 to 14 bit converters rather than around precision.

Order code and package

Order codeINA350ABSIDDFR
Functioninstrumentation amplifier with selectable gain
Gain10 or 20 V/V, set by a pin strap
Sister versionINA350CDS offers 30 or 50 V/V
PackageSOT-23 thin, 8 pins, 4.64 square millimetres
Other bodies10 pin X2QFN of 3 square millimetres, 8 pin WSON of 4 square millimetres
Supply1.8 V to 5.5 V single, or plus and minus 0.9 to 2.75 V
Quiescent current100 microamps typical
Settlingdrives 500 picofarads with under 20 percent overshoot
Temperature rangeminus 40 to plus 125 C
Shutdownavailable on this part
DatasheetSBOSA11 revision A

Electrical parameters that decide the application

Offset voltage0.2 millivolts typical, quoted across all gains
Common mode rejection95 dB typical
Gain error0.05 percent typical at gain 10, 0.06 percent at gain 20
Bandwidth100 kHz typical at gain 10
Input stagehigh impedance, so a bridge source is not loaded
Output stagerail to rail within the limits of the 1.8 V supply
Noisespecified for 10 to 14 bit systems rather than for precision instrumentation
Reference pinsets the output zero point
Package thermala 4.64 square millimetre body has little copper, so self heating follows the load
Supply range1.8 V minimum, which suits a single cell or a 1.8 V digital rail

Points to check before this part goes on a BOM

The two gain options are a pin strap on the same die, not two parts. A board that might need 20 V/V later should route the strap now, because changing it after the board is built means a cut and a wire.

The offset is quoted as 0.2 millivolts typical and there is no maximum in the front page table. That is a deliberate positioning: this part is built against a 10 to 14 bit converter whose own offset and noise already sit in that range.

Gain error of 0.05 percent typical is tighter than the offset would suggest. It comes from an internal resistor network, so it does not move with an external component and it does not need a trim, but it also cannot be improved by one.

One hundred kilohertz at gain 10 is the bandwidth a 12 bit multiplexed system can use. Sampling eight channels at 20 kilohertz with a single amplifier in front of the multiplexer needs a settling time the 100 kHz figure does not leave room for.

The shutdown pin is worth wiring even when it is not used at first. A 100 microamp amplifier that can be taken to a leakage current is the difference between a two year and a one year battery in a coin cell product.

Driving 500 picofarads without overshoot matters when the converter input is a switched capacitor stage. The charge injection of a 12 bit converter looks like a capacitive step, and an amplifier that rings on it converts the ringing into a code error.

Where this order code fits

Portable sensor front ends and single supply bridge boards use it where the converter is 12 bit and the board area is the binding constraint. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the gain be changed in the field? Only by the pin strap. The gain is set by a pin on the ABS version, so a field change needs access to that pin, not a register write.

Is this part a precision instrumentation amplifier? No. It is positioned for 10 to 14 bit systems, with typical offset and rejected terms published rather than minimum and maximum limits.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.