Contact Us

INA332AIDGKR

Brand: Texas Instruments
Texas Instruments INA332AIDGKR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA332AIDGKR — Power Management & Signal Chain | Superb Automation

INA332AIDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA332AIDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA332AIDGKR: the low cost member of the family on a 2500 piece reel

INA332AIDGKR is the low cost member of the CMOS instrumentation amplifier family in the 8 pin VSSOP, on a 2500 piece large reel. It keeps the internal gain of 5, the 415 microamps of supply current, the shutdown pin and the 2 MHz bandwidth, and it accepts a wider specification window: 2 millivolts typical and 8 millivolts maximum of offset at a 5 volt supply, 73 dB of typical rejection and 0.07 per cent of gain error at 5.

The reel differs from the 250 piece T code only in quantity. Both carry the marking B32 and both are moisture level 2, so the decision between them is a line quantity question rather than a technical one. On a channel whose full scale is a few hundred millivolts, this is the cheapest way to get a differential front end with a trimmed gain.

INA332AIDGKR as the vendor document publishes it

Gain5 V/V fixed inside the package, 5 plus 5 times the external ratio above 5
Gain error at 50.07 per cent typical, 0.4 per cent maximum
Gain drift2 ppm per degree typical, 10 ppm per degree maximum
Offset voltage2 millivolts typical, 8 millivolts maximum at 5 volts, 9 maximum over the supply range
Offset drift5 microvolts per degree
Common mode rejection60 dB minimum, 73 dB typical
Common mode rejection at 45 kHz50 dB
Input bias current0.5 picoamps typical, 10 picoamps maximum
Input impedance10 to the 13 ohms in parallel with 3 picofarads
Common mode range at 5 volts0.55 volts to 3.8 volts
Common mode range at 2.7 volts0.35 volts to 1.5 volts
Supply range2.7 volts to 5.5 volts
Quiescent current per channel415 microamps typical, 490 microamps maximum
Shutdown current0.01 microamps typical, 1 microamp maximum
Bandwidth at 3 dB2 MHz at a gain of 25
Slew rate5 volts per microsecond
Voltage noise at 1 kHz46 nanovolts per root hertz
Output swing from the rail20 millivolts, at a gain of 10 or above
Nonlinearity0.001 per cent typical, 0.010 per cent maximum of full scale
Temperature rangeminus 55 to plus 125 degrees
BodyVSSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Vendor statusactive, 2500 piece large reel
Catalogue codeINA332AIDGKR
Vendor stringINA332AIDGKR
MarkingB32
Moisture levellevel 2, 260 degrees, one year floor life

The cheaper flow, and the four rows it costs

INA332 and INA331 share a pinout, a package, a supply range, a quiescent current and the internal gain of 5. The published description of the 332 says plainly that it comes from a special flow that gives the lowest cost in the family, and the price is paid in four specification rows: gain error at 5 rises from 0.02 to 0.07 per cent, common mode rejection falls from 94 to 73 dB typical, the offset moves from the microvolt class to the millivolt class, and the over temperature offset envelope widens with it.

Read as a list, that looks like a large step down. Read against a sensor span, it is often free: a channel whose full scale is 2 volts never sees 2 millivolts of offset, and a channel that only has to detect a threshold rather than to measure a value does not care about rejection at 45 kHz. The step matters on a 10 millivolt bridge, a shunt, or a thermocouple without cold junction compensation, and there the 331 or a chopper part is the answer.

Two millivolts of offset, and the span that makes it irrelevant

The offset of INA332AIDGKR is 2 millivolts typical and 8 millivolts maximum at a 5 volt supply, and 9 millivolts maximum over the full 2.7 to 5.5 volt range. The drift row is 5 microvolts per degree, so a channel that runs 60 degrees above its calibration point adds 300 microvolts on top of whatever the room temperature sort gave.

Those numbers set the smallest signal the part can be used on without a calibration step. At 2 millivolts typical, a 20 millivolt full scale sensor has 10 per cent of offset, and the maximum part has 40 per cent. At a 200 millivolt span the same part is 1 per cent and 4 per cent, and at a 2 volt span the offset is under a tenth of a per cent. A working rule: if the signal is above about 200 millivolts, the 332 is the cheapest way to get a differential front end with a trimmed gain of 5, and below that the offset is the first row to check.

Seventy three decibels, and the frequency where it holds

The common mode rejection of INA332AIDGKR is 60 dB minimum and 73 dB typical, with 50 dB still available at 45 kHz. A 60 dB figure attenuates a 1 volt common mode to 1 millivolt at the input, and at a gain of 5 that is 5 millivolts at the output, which is the same size as the maximum offset of the part.

That comparison is the useful one: on the 332, rejection and offset are in the same class, so improving one without the other does not buy accuracy. A channel that sits on a ground plane shared with a motor drive sees tens of millivolts of common mode at the switching frequency, and 50 dB at 45 kHz turns that into a fraction of a millivolt, which is acceptable. A channel that sits on a 24 volt bus with a 2 volt common mode step needs an input filter, because no instrumentation amplifier with a 73 dB row survives that without one. The input impedance of 10 to the 13 ohms makes a series resistor pair cheap to add.

The same four hundred and fifteen microamps and the same shutdown pin

INA332AIDGKR draws the same 415 microamps typical and 490 maximum per channel as the rest of the family, and shuts down to 0.01 microamps. The shutdown pin returns the part to normal operation within microseconds, so a battery instrument can power the front end per reading instead of leaving it on, and a multichannel logger can share one amplifier between sensors that are read one at a time.

For a part bought on price, the low quiescent current is the second reason to choose it: a 3 volt rail that has to last a year on a lithium cell cannot afford a milliamp front end, and the 490 microamp ceiling leaves room for a 16 bit converter and a reference. The shutdown pin is the third: 0.01 microamps is low enough that the leakage of the board around the part is larger than the part itself, so the sleep current is set by the rest of the circuit and not by the amplifier.

Two megahertz from a part that draws under half a milliamp

The bandwidth of INA332AIDGKR is 2 MHz at a gain of 25 with a slew rate of 5 volts per microsecond, the same rows as the 331 because the two share the amplifier core. That is enough to drive a sampling converter directly at a few hundred kilo-samples per second, and enough to follow a multiplexed channel where the amplifier has to settle after the multiplexer switches.

Two rows temper that. The output reaches within 20 millivolts of each rail only at a gain of 10 or above, so a low gain channel loses the top and bottom of the converter range. And the bandwidth falls with gain, so at a gain of 1000 the part is a few kilohertz wide and the settling time dominates a scan: a 16 channel multiplexed system that allows 50 microseconds per channel spends most of its conversion period waiting for the amplifier rather than for the converter.

Where the low cost member of the family belongs

INA332AIDGKR belongs in a thermistor or position sensor channel, a differential line receiver with a moderate gain, an automotive sensor interface that has to survive minus 55 to plus 125 degrees, and any bridge whose full scale is above a few hundred millivolts and whose accuracy target is a per cent rather than a tenth of one.

It does not belong in a load cell, a shunt or a thermocouple channel, where millivolts of offset against microvolts of signal is the wrong ratio. It does not belong on a single cell, because the supply floor is 2.7 volts. It does not belong where a common mode step of volts has to be rejected at a switching frequency, because 50 dB at 45 kHz is not enough. Our amplifier cross reference page covers the grades and the alternatives on one page, and the vendor consolidation page covers holding the 331 and the 332 on one line rather than two.

The 2500 piece reel is a line quantity and the part is bought on price. Our vendor consolidation page covers holding this part and the tighter grade on one line, and the amplifier cross reference page covers the alternatives.

Is the 332 a sorted 331? No. The published description states a different flow, and the offset, the gain error and the rejection all move together, so the two are separate parts rather than two bins of one.

Does the wider offset matter on a 4 to 20 milliamp loop? At a 2 volt span, 8 millivolts is 0.4 per cent, which is inside the loop tolerance. At a 20 millivolt span it is 40 per cent and the part is the wrong choice.