INA321EA-2K5
Product Specifications
INA321EA-2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA321EA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA321EA-2K5: the wider grade on a reel, and the quantity the two vendor tables disagree on
INA321EA-2K5 is the EA grade of the family on a large reel: 1 millivolt maximum of offset, 80 dB minimum of rejection and 0.07 per cent of gain error at a gain of 5, for a lower price than the E grade in the same package and with the same 40 microamps of supply current.
The reel quantity is the row that has to be read twice. The ordering table on the first page of the vendor document prints this code as a 3000 piece tape and reel, while the package addendum at the end of the same document prints 2500 pieces on a large reel. The addendum is the newer table and the one the distributor sees, so 2500 is the number to plan a line against, and a purchase order that assumes 3000 comes up 500 pieces short.
INA321EA-2K5 as the vendor document publishes it
| Quiescent current | 40 microamps per channel |
| Shutdown current | under 1 microamp |
| Offset voltage | 200 microvolts typical, 1 millivolt maximum |
| Offset drift | 2 microvolts per degree |
| Input bias current | 10 picoamps |
| Common mode rejection | 80 dB minimum, 94 dB typical |
| Gain equation | 5 plus 5 multiplied by the ratio of the two external resistors |
| Gain error at 5 | 0.07 per cent |
| Gain drift | 2 ppm per degree |
| Bandwidth at 3 dB | 500 kHz at a gain of 5 |
| Slew rate | 0.8 volts per microsecond |
| Output swing to the positive rail | 20 millivolts |
| Supply range | 2.7 volts to 5.5 volts, single or bipolar |
| Common mode range at 5 volts | 0.55 volts to 3.8 volts |
| Common mode range at 2.7 volts | 0.35 volts to 1.5 volts |
| Input impedance | 10 to the 13 ohm in parallel with 3 picofarads |
| Body | MSOP, 8 pin, DGK, 3.00 by 3.00 millimetres |
| Temperature range | minus 55 to plus 125 degrees |
| Vendor status | active, 2500 piece large reel in the addendum, 3000 in the page one ordering table |
| Catalogue code | INA321EA-2K5 |
| Vendor string | INA321EA/2K5, printed with a slash |
| Grade | EA, 1 millivolt maximum offset |
| Marking | C21 |
| Moisture level | level 2, 260 degrees, one year floor life |
The letter after the part number widens the window
The INA321 is sold in two grades and the difference is entirely in the specification columns. The E grade holds 200 microvolts typical and 500 microvolts maximum of offset, 90 dB minimum of common mode rejection and 0.02 per cent of gain error at a gain of 5. The EA grade holds 1 millivolt maximum of offset, 80 dB minimum of rejection and 0.07 per cent of gain error, for a lower price.
That is the whole of the choice, and it is worth stating plainly because the two codes look alike on a purchase order. A channel that measures a 10 millivolt bridge signal has 1 millivolt of offset on the EA grade, which is 10 per cent of full scale before any gain is applied; the E grade has 0.5 millivolt, or 5 per cent, and neither is a precision channel without a calibration step. A channel that only has to detect a threshold rather than to measure a value can use either.
The gain lives outside the package
The gain of INA321EA-2K5 is 5 plus 5 times the ratio of two external resistors, so the minimum gain is 5 and the maximum is about 1000 depending on the resistor values. Everything above 5 comes from the resistor pair, and that is the part of the channel the data sheet does not trim.
Two consequences follow. The first is that the gain accuracy at 5 is specified at 0.02 per cent while the gain at 100 is only as good as the resistors: a pair of 1 per cent resistors gives a 1 per cent channel, and a pair of 0.1 per cent resistors gives 0.1 per cent. The second is that the resistor network is a place to put a filter, a multiplexer or a calibration trim, because the two nodes are brought out. A channel that has to trim gain in production can put a potentiometer in the divider, and the drift of that potentiometer becomes the drift of the gain.
Where a micropower instrumentation amplifier fits
INA321EA-2K5 fits a portable medical front end for ECG or EMG, a bridge or thermistor channel in a handheld instrument, a 4 to 20 milliamp loop that has to run on the loop current, and a battery powered field meter that reads a differential line. The 40 microamps, the shutdown pin and the 500 kHz bandwidth at a gain of 5 are the three rows that make those applications possible.
It stops at four things. The minimum gain is 5, so a unity gain buffer is a different part. The offset is in the hundreds of microvolts on the E grade and a millivolt on the EA grade, so a precision DC channel needs a chopper stabilised amplifier instead. The supply floor is 2.7 volts, which rules out a single cell. And the part is specified to minus 55 to plus 125 degrees but with the offset and rejection rows that belong to a low cost amplifier, so an instrumentation channel that has to hold 0.01 per cent over temperature belongs elsewhere. Our amplifier cross reference page lists the alternatives by front end type.
Forty microamps per channel, and under one in shutdown
INA321EA-2K5 draws 40 microamps per channel and under 1 microamp with the shutdown pin pulled low, from a supply of 2.7 to 5.5 volts. The shutdown feature is not a gimmick on this part: a battery instrument that wakes once a second and reads a bridge for 2 milliseconds spends 0.2 per cent of its life in measurement, and a front end that draws 40 microamps while asleep empties a coin cell in weeks.
The return from shutdown takes microseconds, which is fast enough to be part of a scan rather than a power cycle. That matters for a multiplexed channel where several sensors share one amplifier: the part is powered for the channel that is being read and shut down for the rest, and the settling time of the amplifier is now part of the channel budget along with the multiplexer and the converter.
Ten picoamps of bias against a high impedance source
The input bias current of INA321EA-2K5 is 10 picoamps, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. A bridge of 350 ohms does not care about either figure. A pH electrode, a photodiode or a 10 megohm thermistor does: 10 picoamps into 10 megohms is 100 microvolts, which is the same order as the offset of the EA grade.
That is why the bias current and the offset have to be read together. A high impedance source converts bias current into an offset that is indistinguishable from the amplifier's own, and the conversion is linear in the source resistance. The same arithmetic applies to the bias current path: an input that has no DC return charges the 3 picofarads until the amplifier leaves its common mode range, and the symptom is a channel that works on the bench and drifts on the board.
Five hundred kilohertz at a gain of five
The bandwidth of INA321EA-2K5 is 500 kHz at a gain of 5, with a slew rate of 0.8 volts per microsecond and an output that swings to within 20 millivolts of the positive rail. For a micropower part that is a wide front end, and it is what makes the family usable in front of a fast converter rather than only in a slow logger.
The bandwidth falls as the gain rises, so a gain of 100 channel is a few tens of kilohertz wide, and the output stage has to drive the sampling capacitor of the converter as well as the feedback network. The 20 millivolt swing to the rail is the row that decides the top of the range: a 12 bit converter with a 4.096 volt reference has a 1 millivolt least significant bit, so 20 millivolts of headroom is 20 codes that cannot be used, and a channel that needs the top of the range has to run the amplifier from a rail above the reference.
Two tables, two quantities, and the addendum is the one that ships. Our traceability report page covers the label check on receipt, and the vendor consolidation page covers holding one grade rather than two.
Is the reel 2500 or 3000 pieces? The package addendum prints 2500 large reel and the older ordering table prints 3000; plan against the addendum and confirm on the label.
Is the EA grade a different die? No, the same die with a wider offset and gain window; the 40 microamps and the pinout are shared with the E grade.