Contact Us

INA321EA-250

Brand: Texas Instruments
Texas Instruments INA321EA-250 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA321EA-250 — Power Management & Signal Chain | Superb Automation

INA321EA-250

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA321EA-250 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA321EA-250: the wider grade on a 250 piece reel

INA321EA-250 is the EA grade in the 8 pin MSOP on a 250 piece small reel, the carrier a pilot run and a repair bench actually use. The electrical rows are the grade's: 1 millivolt maximum of offset, 80 dB minimum of rejection, 0.07 per cent of gain error at 5, 10 picoamps of bias current and 500 kHz of bandwidth at that gain.

The part is specified from minus 55 to plus 125 degrees, which is wider than most of the family's neighbours, and the shutdown pin takes the supply current under 1 microamp between readings. The 250 piece reel carries the marking C21 and moisture level 2 with a one year floor life, so a small reel can sit on a shelf without a bake clock.

INA321EA-250 as the vendor document publishes it

Quiescent current40 microamps per channel
Shutdown currentunder 1 microamp
Offset voltage200 microvolts typical, 1 millivolt maximum
Offset drift2 microvolts per degree
Input bias current10 picoamps
Common mode rejection80 dB minimum, 94 dB typical
Gain equation5 plus 5 multiplied by the ratio of the two external resistors
Gain error at 50.07 per cent
Gain drift2 ppm per degree
Bandwidth at 3 dB500 kHz at a gain of 5
Slew rate0.8 volts per microsecond
Output swing to the positive rail20 millivolts
Supply range2.7 volts to 5.5 volts, single or bipolar
Common mode range at 5 volts0.55 volts to 3.8 volts
Common mode range at 2.7 volts0.35 volts to 1.5 volts
Input impedance10 to the 13 ohm in parallel with 3 picofarads
BodyMSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Temperature rangeminus 55 to plus 125 degrees
Vendor statusactive, 250 piece small reel
Catalogue codeINA321EA-250
Vendor stringINA321EA/250, printed with a slash
GradeEA, 1 millivolt maximum offset
MarkingC21
Moisture levellevel 2, 260 degrees, one year floor life

Forty microamps per channel, and under one in shutdown

INA321EA-250 draws 40 microamps per channel and under 1 microamp with the shutdown pin pulled low, from a supply of 2.7 to 5.5 volts. The shutdown feature is not a gimmick on this part: a battery instrument that wakes once a second and reads a bridge for 2 milliseconds spends 0.2 per cent of its life in measurement, and a front end that draws 40 microamps while asleep empties a coin cell in weeks.

The return from shutdown takes microseconds, which is fast enough to be part of a scan rather than a power cycle. That matters for a multiplexed channel where several sensors share one amplifier: the part is powered for the channel that is being read and shut down for the rest, and the settling time of the amplifier is now part of the channel budget along with the multiplexer and the converter.

The letter after the part number widens the window

The INA321 is sold in two grades and the difference is entirely in the specification columns. The E grade holds 200 microvolts typical and 500 microvolts maximum of offset, 90 dB minimum of common mode rejection and 0.02 per cent of gain error at a gain of 5. The EA grade holds 1 millivolt maximum of offset, 80 dB minimum of rejection and 0.07 per cent of gain error, for a lower price.

That is the whole of the choice, and it is worth stating plainly because the two codes look alike on a purchase order. A channel that measures a 10 millivolt bridge signal has 1 millivolt of offset on the EA grade, which is 10 per cent of full scale before any gain is applied; the E grade has 0.5 millivolt, or 5 per cent, and neither is a precision channel without a calibration step. A channel that only has to detect a threshold rather than to measure a value can use either.

Five hundred kilohertz at a gain of five

The bandwidth of INA321EA-250 is 500 kHz at a gain of 5, with a slew rate of 0.8 volts per microsecond and an output that swings to within 20 millivolts of the positive rail. For a micropower part that is a wide front end, and it is what makes the family usable in front of a fast converter rather than only in a slow logger.

The bandwidth falls as the gain rises, so a gain of 100 channel is a few tens of kilohertz wide, and the output stage has to drive the sampling capacitor of the converter as well as the feedback network. The 20 millivolt swing to the rail is the row that decides the top of the range: a 12 bit converter with a 4.096 volt reference has a 1 millivolt least significant bit, so 20 millivolts of headroom is 20 codes that cannot be used, and a channel that needs the top of the range has to run the amplifier from a rail above the reference.

The gain lives outside the package

The gain of INA321EA-250 is 5 plus 5 times the ratio of two external resistors, so the minimum gain is 5 and the maximum is about 1000 depending on the resistor values. Everything above 5 comes from the resistor pair, and that is the part of the channel the data sheet does not trim.

Two consequences follow. The first is that the gain accuracy at 5 is specified at 0.02 per cent while the gain at 100 is only as good as the resistors: a pair of 1 per cent resistors gives a 1 per cent channel, and a pair of 0.1 per cent resistors gives 0.1 per cent. The second is that the resistor network is a place to put a filter, a multiplexer or a calibration trim, because the two nodes are brought out. A channel that has to trim gain in production can put a potentiometer in the divider, and the drift of that potentiometer becomes the drift of the gain.

Where a micropower instrumentation amplifier fits

INA321EA-250 fits a portable medical front end for ECG or EMG, a bridge or thermistor channel in a handheld instrument, a 4 to 20 milliamp loop that has to run on the loop current, and a battery powered field meter that reads a differential line. The 40 microamps, the shutdown pin and the 500 kHz bandwidth at a gain of 5 are the three rows that make those applications possible.

It stops at four things. The minimum gain is 5, so a unity gain buffer is a different part. The offset is in the hundreds of microvolts on the E grade and a millivolt on the EA grade, so a precision DC channel needs a chopper stabilised amplifier instead. The supply floor is 2.7 volts, which rules out a single cell. And the part is specified to minus 55 to plus 125 degrees but with the offset and rejection rows that belong to a low cost amplifier, so an instrumentation channel that has to hold 0.01 per cent over temperature belongs elsewhere. Our amplifier cross reference page lists the alternatives by front end type.

Ten picoamps of bias against a high impedance source

The input bias current of INA321EA-250 is 10 picoamps, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. A bridge of 350 ohms does not care about either figure. A pH electrode, a photodiode or a 10 megohm thermistor does: 10 picoamps into 10 megohms is 100 microvolts, which is the same order as the offset of the EA grade.

That is why the bias current and the offset have to be read together. A high impedance source converts bias current into an offset that is indistinguishable from the amplifier's own, and the conversion is linear in the source resistance. The same arithmetic applies to the bias current path: an input that has no DC return charges the 3 picofarads until the amplifier leaves its common mode range, and the symptom is a channel that works on the bench and drifts on the board.

Two hundred and fifty pieces covers a pilot, a bench and a first article. Our BOM scrubbing page covers the grade against the bill of materials, and the amplifier cross reference page covers the precision alternatives where a millivolt of offset is too much.

How many pieces on the reel? 250, small tape and reel, marking C21.

Can this grade be used for a bridge sensor? It can detect a change, but 1 millivolt of maximum offset against a 10 millivolt bridge span is 10 per cent of full scale, so a measuring channel needs the E grade or a calibration step.