INA299A1IDBVR
Product Specifications
INA299A1IDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA299A1IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA299A1IDBVR: a 20 V/V bidirectional monitor that runs on 650 uA
The INA299A1IDBVR is the 20 V/V member of the INA299 family, a bidirectional current sense amplifier with a common mode range of 2 V below ground to 80 V above it. It is the low power member of the wider family: quiescent current is 650 uA against 1.5 mA on the INA293 and 2.5 mA on the INA296, which matters when the monitor sits on a standby rail that has a microamp budget of its own.
At 20 V/V a 2 milliohm shunt carrying 20 A gives 40 mV in and 800 mV out, so a 3.3 V host uses about a quarter of its range at the working current and can still read a 4 times overload before the output saturates. Gain error is 0.25 per cent maximum with 10 ppm per degree drift, offset is 150 uV maximum with 0.5 uV per degree drift, and the DC common mode rejection is 120 dB typical, which is a step below the 160 dB of the INA293 but comes with a supply range that stops at 12 V and a body that costs less board area.
Key data for the INA299A1IDBVR
| Gain | 20 V/V on the A1 code; the family also offers 50 and 100 V/V as A2 and A3 |
| Common mode | Minus 2 V to 80 V operational, minus 12 V to 85 V survival, so a 48 V rail fits and a 72 V pack does not |
| Accuracy | Gain error 0.25 per cent maximum with 10 ppm per degree drift, offset 150 uV maximum with 0.5 uV per degree drift |
| Speed | 650 kHz small signal bandwidth at 20 V/V, 2.5 V per microsecond slew rate, 6.5 microseconds settling to 1 per cent |
| Rejection | 120 dB typical DC common mode rejection |
| Supply | 2.7 V to 12 V single rail, 650 uA operating current, minus 40 C to 125 C |
Body, marking and reel data
| Body | DBV, 6 pin SOT-23 at 2.90 mm by 2.80 mm |
| Reel | 3000 pieces on a 180 mm reel, 8.4 mm tape width, quadrant Q3 on the A1 and A3 rows |
| Tape | 3.2 mm pocket depth and 1.4 mm pocket height, so a 1.1 mm part sits well inside the cavity |
| Pins | IN plus, IN minus, VS, GND, REF and OUT; a single reference pin, so the zero point is set by one voltage |
| Line | INA299 is a 2025 release, revised September 2025, so the document is current rather than a legacy revision |
Where a 650 uA monitor is the right choice
The INA299 answers a specific problem: a current monitor on a rail that is always on. A 48 V telecom shelf keeps its housekeeping supply live while the payload sleeps, and a monitor that draws 2.5 mA from that rail spends more energy than the leakage it is measuring. At 650 uA the part can stay powered through the sleep state, which removes the need for a load switch and the offset error that a switched monitor brings when it wakes.
The 12 V supply ceiling is the constraint to check first. A 48 V rail is measured at the inputs, not at the supply, so a 48 V bus is fine as long as the amplifier itself is fed from a 3.3 V or 5 V housekeeping rail. What the ceiling rules out is powering the part from a 15 V rail that happens to be available. The 80 V common mode and the minus 2 V lower limit cover the ringing that a hot plug event puts on a 48 V backplane, and the 6.5 microsecond settling keeps a sampled reading valid when the host multiplexes several monitors onto one converter channel. Where a board is comparing this part against the higher voltage members, our power management cross reference tabulates supply, common mode and quiescent current side by side, and the component lead time solutions note covers what to do when one member of a family is quoted at 26 weeks and a sibling is in stock.
Buyer questions on the INA299A1IDBVR
Can the output be used with a 5 V converter when the supply is 3.3 V? No. The output swings inside the supply, so a 3.3 V part cannot drive a 5 V full scale input. Set the shunt so that full scale arrives below the supply, or move the amplifier to a 5 V rail.
What is the reference pin for? It offsets the output, which is how a bidirectional measurement is centred. Tying it to ground gives a one sided reading, tying it to a mid rail voltage gives a signed reading with the zero in the middle.
Is the 150 uV offset a maximum over temperature? The maximum is the room temperature figure and the drift row carries the rest, so the worst case over the range is the maximum plus the drift times the temperature excursion, which at 125 C is about 230 uV.
Availability and ordering notes
INA299A1IDBVR is the 20 V/V member in the 6 pin SOT-23, 3000 pieces on a 180 mm reel. The A2 and A3 gain options share the body and the reel, so a mixed requirement can ship on one tape. Because the family is a 2025 release, the distributor listing lags the vendor document, and a quotation that shows no stock should be checked against the vendor ship date rather than treated as an end of life signal.