UCC28C44D
Product Specifications
UCC28C44D
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC28C44D from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC28C44D: the 14.5 V lockout member with the half duty limit, in an eight pin SOIC
The UCC28C44D is one of the six UCCx8C4x current mode controllers that drop into a UCx84x socket. The -44 suffix sets two things that belong together in an off line converter: a lockout of 14.5 V on and 9 V off, which is the widest window in the family and gives a bias capacitor time to charge from a start up resistor, and a maximum duty of about 48 percent, because the output stage divides the oscillator by two. That combination is what a single ended forward converter or a half bridge needs at high line, where a duty above half a cycle would not leave the core time to reset.
The rest of the part is the family standard: 50 microamps of start up current, 2.3 mA of run current at 52 kHz, a 5 V reference trimmed to 1 percent, a 35 ns current sense to output delay, and a 1 A peak totem pole output with 25 ns rise and 20 ns fall. The trimmed oscillator discharge current is the quiet improvement over the bipolar UC3844 that this part replaces: the maximum duty and the dead time are set by a current the vendor controls, so a resistor and capacitor pair gives the same duty across a temperature range rather than drifting with the process.
Key electrical data for the UCC28C44D
| Supply | Start up 50 microamps typical, run current 2.3 mA at 52 kHz, operation to 1 MHz |
| Lockout | Turn on 14.5 V inside a 13.5 V to 15.5 V window, turn off 9 V inside a 8 V to 10 V window |
| Reference | 5 V at 1 percent initial accuracy, 4.9 V to 5.1 V, error amplifier reference 2.5 V |
| Output | 1 A peak totem pole, rail to rail, 25 ns rise and 20 ns fall, 35 ns current sense delay |
| Duty | 47 percent minimum and 48 percent typical maximum, output frequency half the oscillator frequency |
| Temperature | UCC28C4x rows are rated minus 40 C to 125 C, the UCC38C4x siblings 0 C to 85 C |
Package, marking and reel data
| Body | D, SOIC 8 pin, marking 28C44 on the published rows |
| Reel | 2500 pieces on a 330 mm reel, 12.4 mm carrier on the published rows |
| Finish | NIPDAU at moisture level 1 unlimited on the SOIC rows of this family |
| Note | The addendum prints DGK, DGKR, DR and DRG4 rows, and the plain D string is not one of them |
The plain D string is not a published addendum row
This is worth knowing before the first order. The vendor addendum for the family prints UCC28C44DGK, UCC28C44DGKR, UCC28C44DR and UCC28C44DRG4, and it does not print UCC28C44D on its own. The catalogue entry uses the plain D string, which is the SOIC body by the family's own naming, but a purchasing system that matches strings against the addendum will not find it. The nearest published SOIC row is UCC28C44DR at 2500 pieces, and the G4 row of the same body prints NIPDAU at level 1. The safe way to order is to quote the suffix the vendor publishes and to state the body, rather than to rely on the short string. Our supplier onboarding checklist page covers how we resolve a string that does not match a published row.
The duty limit is the second thing to check on a substitution. A customer who has been running a -43 with 96 percent duty and fits a -44 in the same socket gets half the on time and a converter that cannot hold regulation at low line. The lockout moves the other way: the -44 starts at 14.5 V where the -43 starts at 8.4 V, so a 12 V bias rail will not start a -44 at all. Both facts are in the device comparison table and both are easy to miss when the package and the pinout are identical.
Buyer questions on the UCC28C44D
Does the part work in a UC3844 socket? The pinout matches and the vendor states the family as a pin for pin replacement. The duty limit and the lockout follow the suffix, so the socket has to be checked against the member being fitted.
Why is the maximum duty only 48 percent? The output stage toggles on alternate oscillator cycles on the -41, -44 and -45 members, so the output frequency is half the oscillator frequency and the duty cannot exceed half a cycle.
Can a 12 V rail start this part? Not reliably. The turn on threshold is 14.5 V nominal, so a 12 V bias never reaches it. A -43 or a -45 with the 8.4 V window is the right member for a 12 V rail.
Availability and cross reference
The family prints active across both bodies, and the choice between the 8.4 V and the 14.5 V lockout is the one that decides whether a bias arrangement works. We hold both members in the SOIC and the VSSOP bodies and quote the full string including the body, and the substitution rules are on our power management cross reference page.