UCC33420RAQR
Product Specifications
UCC33420RAQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC33420RAQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC33420RAQR: 1.5 W of isolated 5 V from a 5 V input in a 4 mm by 5 mm module
The UCC33420RAQR is an isolated DC to DC module with the transformer inside the package. It takes 4.5 V to 5.5 V in, delivers 1.5 W at a regulated 5.0 V with an optional 5.5 V headroom setting, and carries a 3 kVRMS isolation rating with a 6.5 kVPK surge and 1159 VPK of working voltage. Load regulation is 0.5 percent typical and line regulation is 4 mV per volt typical, which is enough for a gate driver bias or a transceiver supply without a post regulator. The whole part sits in a 12 pin VSON measuring 4.00 mm by 5.00 mm at 1.00 mm tall, with more than 4.1 mm of clearance and creepage across the barrier.
What the module replaces is the familiar arrangement of a push pull driver, a small transformer, a rectifier and a filter, spread across twenty square millimetres and a hand wound part. Because the transformer is integrated, the leakage inductance and the winding capacitance are fixed and known, and the vendor can specify a common mode transient immunity of 200 V per nanosecond and an emission level that meets CISPR 32 class B with adaptive spread spectrum modulation. Protection covers overload, short circuit and thermal shutdown, and the enable pin carries a fault report back to the primary side.
Key electrical data for the UCC33420RAQR
| Input | 4.5 V to 5.5 V, one rail, no external transformer or rectifier |
| Output | 5.0 V or 5.5 V selectable, 300 mA available at 5.0 V, 1.5 W maximum |
| Regulation | 0.5 percent typical load regulation, 4 mV per volt typical line regulation |
| Isolation | 3 kVRMS rating, 6.5 kVPK surge, 1159 VPK working voltage, 200 V per nanosecond CMTI |
| Emission | Meets CISPR 32 class B with adaptive spread spectrum modulation |
| Protection | Overload, short circuit, thermal shutdown, low inrush soft start, enable with fault report |
Package, marking and reel data
| Body | RAQ, VSON FCRLF 12 pin, 4.00 mm by 5.00 mm, 1.00 mm height |
| Reel | 3000 pieces on a 330 mm reel, 12.0 mm carrier, quadrant Q2 |
| Finish | NIPDAU at moisture level 3, 260 C peak, 168 hour floor life |
| Temperature | Ambient minus 40 C to 125 C |
Where a module beats a discrete isolated bias
The first case is a half bridge gate driver that needs a floating supply for the high side switch. A discrete arrangement needs a bootstrap capacitor that has to be refreshed, and that refresh fails at 100 percent duty or during a long on time. A module with its own isolated output holds the bias regardless of duty. The second case is an isolated transceiver on an RS-485 or CAN port, where the module supplies the isolated side and the isolator handles the data, and both parts come from one vendor with compatible timing. The third case is an E-mode GaN gate that wants a well regulated bias rather than a bootstrap rail.
The limitation is the 1.5 W ceiling and the fixed 5 V output. A gate driver that draws 200 mW of average power but 4 W of peak is fine, because the module's output capacitor supplies the peak and the module refills it. A continuous load above 300 mA needs a different arrangement. The moisture level of 3 with a 168 hour floor life is the other practical point: a level 3 part that has been open for a week needs a bake before reflow, and the label on the reel is the only place that information lives. Our incoming inspection plan page covers how we check and record it.
Buyer questions on the UCC33420RAQR
Can the output be used as a general purpose 5 V rail? It is a 1.5 W isolated rail, so it suits a bias load rather than a system rail. Above 300 mA at 5 V the module is outside its rating.
Does the module need an external snubber or filter? The vendor's arrangement uses input and output ceramic capacitors close to the pins. The integrated transformer removes the leakage ring that a discrete transformer produces, so no snubber is specified.
What does the 5.5 V setting change? It adds headroom for a downstream linear regulator, which is useful when the isolated side needs a quiet 5 V and the module output has to sit above the dropout.
Availability and cross reference
The part is active in the addendum at 3000 pieces on a reel with a Q2 tape orientation. Because it replaces a hand wound transformer and four other parts, a customer who moves to it usually removes a magnetic component from the bill of materials and changes the board at the same time. We hold the module and the matching digital isolators together, and the consolidation logic is on our BOM consolidation page.