UCC3804PWTR
Product Specifications
UCC3804PWTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC3804PWTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC3804PWTR: the half duty member of the UCC280x family, in the TSSOP body
The UCC3804PWTR is the 50 percent duty member of the UCC280x family with the off line lockout of 12.5 V on and 8.3 V off. It carries the same current mode control, the same 1 A totem pole output, the same 70 ns current sense delay and the same internal soft start as the rest of the family, and differs from the UCC3802 by one internal connection that halves the maximum duty. That half cycle limit is what a forward converter needs so the core can reset, and it is also the limit a push pull or half bridge stage imposes by construction.
Start up current is 100 microamps and run current is 500 microamps, which are the numbers that make a resistor from a high voltage rail a practical bias source. The oscillator reaches 1 MHz with a resistor and capacitor pair on the RC and CT pins, and the leading edge blanking window covers the gate charge spike so the sense line needs no RC filter. The reference is 5 V at 1.5 percent with the error amplifier at 2.5 V.
Key electrical data for the UCC3804PWTR
| Supply | Start up 100 microamps typical, run current 500 microamps, operation to 1 MHz |
| Lockout | Turn on 12.5 V, turn off 8.3 V, the off line option in the family |
| Reference | 5 V at 1.5 percent tolerance, error amplifier input at 2.5 V |
| Output | 1 A totem pole, 70 ns current sense to output, internal leading edge blanking |
| Duty | About 50 percent maximum through the toggle latch |
| Temperature | UCC380x rows are published at 0 C to 70 C, the UCC280x siblings at minus 40 C to 125 C |
Package, marking and reel data
| Body | PW, TSSOP 8 pin, 4.40 mm by 3.00 mm per the family package table |
| Reel | 2000 pieces on a large tape and reel on the row that prints a quantity |
| Finish | Call TI on the plain row, NIPDAU at moisture level 2 with a one year floor life on the .A row |
| Status | The plain PWTR row prints active, the .A row prints obsolete, and the addendum labels both rows UCC3805 |
Two fields in the addendum need a call before ordering
The row printed UCC3804PWTR shows the package as SOIC 8, while the catalogue code carries the PW suffix that the family table assigns to the TSSOP body, and the marking column on the same rows reads UCC3805 rather than UCC3804. Neither of those is a reason to doubt the part, but both are reasons to confirm the body and the marking before a reel is accepted. A 2000 piece reel of the wrong body would stop a line, and the marking is the only field a receiving inspection can check against the label without opening the tape. Our incoming inspection plan page covers the checks we run at goods in.
The electrical difference from the UCC3802 is one internal connection, which is why a substitution between them is tempting and dangerous. A forward converter fitted with the 100 percent duty part will run at high line and then walk the core into saturation at low line, because the reset time disappears. The reverse substitution, a 50 percent part into a boost that needs 80 percent, simply cannot regulate. Both codes are in the same body and the same reel size, so the mistake is a code typo away, and the only external sign of it is a converter that runs correctly on the bench and then saturates at low line under load. A receiving inspection cannot catch that, which is why the code and the row have to be checked at the order stage rather than at goods in.
Buyer questions on the UCC3804PWTR
Does the TSSOP body have the same pinout as the SOIC? Yes. The family table lists the D and PW bodies with the same pin functions, so the footprint differs and the electrical behaviour does not.
Is the .A row a different part? It is the same string with a different addendum row, and that row prints obsolete while the plain row prints active. We confirm the active row in writing before quoting.
Can the duty limit be raised externally? No. The limit is set by the toggle latch inside the device, so the choice of member is the only way to change it.
Availability and cross reference
The reel is 2000 pieces on the row that prints a quantity, and the family covers both duty limits and three temperature grades in the same pinout. We hold the TSSOP and SOIC bodies and quote the suffix with the body stated, because the addendum fields on this code are inconsistent. The substitution rules and the checks we run are on our how to verify a drop in replacement page.