Contact Us

UCC28251RGPR

Brand: Texas Instruments
Texas Instruments UCC28251RGPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28251RGPR — Power Management & Signal Chain | Superb Automation

UCC28251RGPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28251RGPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28251RGPR: the same bridge controller with a minimum frequency low enough for a 400 V stage

The UCC28251RGPR is a functional variant of the UCC28250, in the 20 pin QFN body packed 3000 pieces on a reel. The feature list is nearly identical: prebiased start up, synchronous rectifier outputs with programmable delays including zero, voltage mode with input voltage feedforward or current mode, primary or secondary side control, a 3.3 V reference at 1.5 percent, and 1 percent accurate cycle by cycle overcurrent. The difference the vendor calls out is a lower minimum operating frequency, and the numbers behind it are in the electrical table: when the frequency is programmed by the RT pin and synchronisation is on, the switching frequency can fall to 42 kHz, and when it is set by RT alone it can go as low as 27 kHz.

That matters in an off line stage. A 400 V input converter running at 100 kHz has a minimum duty cycle that is hard to hold at light load, and a controller that cannot drop its frequency ends up skipping cycles and producing audible noise. The 51 variant lets the frequency fall so the stage stays in continuous conduction at light load, which is the mode the vendor names for 400 V DC to DC and for 48 V full bridge and half bridge supplies. The maximum is unchanged: the oscillator reaches 1.4 MHz, which is 700 kHz of switching frequency.

Key electrical data for the UCC28251RGPR

Reference3.3 V output at 1.5 percent, the same window as the UCC28250
FrequencyOscillator 50 kHz to 1.4 MHz, which is 25 kHz to 700 kHz of switching frequency
Minimum42 kHz switching frequency under synchronisation, as low as 27 kHz when set by RT alone
SyncExternal synchronisation from 84 kHz to 1.89 MHz of oscillator frequency, clamped at the bottom
OutputsTwo primary plus two synchronous rectifier outputs, programmable delays including zero
Protection1 percent cycle by cycle overcurrent, programmable soft start, hiccup restart timer

Package, marking and reel data

BodyRGP, VQFN 20 pin, 4.00 mm by 3.50 mm, marked 2825
Reel3000 pieces on a 330 mm reel, quadrant Q1 in the tape drawing
FinishNIPDAU at moisture level 1 unlimited on the plain row, level 2 with a one year floor life on the .A row
GradeAmbient minus 40 C to 125 C on both rows

The low frequency limit changes the magnetics, not just the noise

A converter that can run at 27 kHz needs a transformer that does not saturate at 27 kHz, which means more turns or more core than a 100 kHz part of the same power. That is a real cost, and it is why the low limit is a feature for a specific job rather than a universal improvement. The job is a wide input range supply that spends most of its life at high line, where the duty cycle is short and the frequency has to fall to keep the volt second balance inside the loop. The 51 variant gives that room without an external clock generator or a second controller.

The QFN body is the other practical difference. A 4 mm by 3.5 mm body with an exposed pad puts the heat into the board, which is what a 20 pin controller needs when it sits next to two gate drivers. The tape drawing gives the quadrant as Q1, and the reel is 3000 pieces rather than the 2000 of the TSSOP sibling, so a build that changes package changes its reel count as well. Our material requirements planning page sets out how we handle that difference in a forecast.

Buyer questions on the UCC28251RGPR

Can the UCC28250 and the UCC28251 be interchanged? Not blindly. The pinout and the body options overlap, but the minimum frequency differs and a magnetic component chosen for one is not automatically valid for the other.

Is the 27 kHz figure a normal operating point? It is the floor when the frequency is set by RT alone. Normal operation sits far above it, and the low limit exists so a wide input stage can hold regulation at light load.

Does the QFN body need thermal vias? It does. The exposed pad is the thermal path and the ground connection, so the via array under the part is part of the electrical arrangement rather than an optional addition.

Availability and cross reference

Both bodies of this controller print active, and the QFN reel is 3000 pieces against 2000 for the TSSOP. The controller is usually ordered with a half bridge driver and a dual low side driver, and those three codes have to be planned together because a shortage in any one of them stops the build. We hold the set and the substitution rules, which are on our BOM consolidation page.