INA219BID
Product Specifications
INA219BID
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA219BID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA219BID: the B grade in a tube, and the row the addendum marks obsolete
INA219BID is the B grade of the I2C current and power monitor in the eight pin SOIC, in a tube. It is the tighter grade: 10 microvolts typical and 50 maximum of offset at the narrowest gain setting, 0.3 per cent of current error at room temperature and 0.5 per cent over minus 25 to plus 85 degrees, against 100 microvolts and 1 per cent on the A grade.
The carrier is the problem with this code. The addendum read for this page prints INA219BID with the status Obsolete and no packing quantity, while INA219BIDR, the same grade and body on a 2500 piece large reel, is active. A tube of an eight pin SOIC is a prototype quantity anyway, and the page states the position so that a build is not planned around a row the vendor no longer packs.
INA219BID as the vendor document publishes it
| ADC resolution | 12 bits |
| Shunt least significant bit | 10 microvolts |
| Bus least significant bit | 4 millivolts |
| Shunt full scale | 40, 80, 160 or 320 millivolts, selected by the gain bits |
| Bus full scale | 16 or 32 volts, selected by one configuration bit |
| Bus input rating | 0 to 26 volts, absolute maximum 26 volts |
| Common mode rejection | 100 dB minimum, 120 typical |
| Offset voltage | 10 microvolts typical and 50 maximum at the narrowest range, 40 and 100 on the widest |
| Current measurement error | 0.2 per cent typical, 0.3 maximum, 0.5 per cent over temperature |
| Bus voltage measurement error | 0.2 per cent typical, 0.5 maximum |
| Differential nonlinearity | 0.1 bit |
| Conversion time | 532 microseconds typical, 586 maximum at 12 bits |
| Addresses | 16, from 0x40 to 0x4F, set by two pins |
| Supply range | 3 volts to 5.5 volts |
| Supply current | 1 milliamp maximum |
| Body | SOIC, 8 pin, D |
| Temperature range | minus 40 to plus 125 degrees |
| Vendor status | obsolete in the package addendum, no packing quantity printed |
| Catalogue code | INA219BID |
| Vendor string | INA219BID, obsolete; INA219BIDR is the active row |
| Carrier | tube |
| Grade | B, 50 microvolts maximum offset |
Twelve bits at 532 microseconds
INA219BID converts the shunt drop and the bus voltage with a 12 bit converter whose shunt bit is 10 microvolts and whose bus bit is 4 millivolts. A conversion takes 532 microseconds typical and 586 maximum at full resolution, and the part can be programmed to fewer bits or to a running average, which trades time for noise without host work.
The two channels are converted at different moments, and the document is explicit that at full resolution with 128 sample averaging up to 68 milliseconds can pass between the current and the bus reading that are multiplied together. For a steady load that is invisible. For a load that steps, the reported power can mix the current before a step with the bus voltage after it, and a host that uses power for protection rather than for logging should read the two registers and do the multiplication itself at the moment it chooses.
Two grades, and the half per cent that separates them
INA219BID is the tighter of the two grades of this current and power monitor. Current measurement error is 0.2 per cent typical and 0.3 maximum, and 0.5 per cent maximum over minus 25 to plus 85 degrees, against 0.5 and 1 per cent on the A grade. The offset rows follow: 10 microvolts typical and 50 maximum at the narrowest gain setting, against 100 maximum on the A grade.
The difference is a screening step rather than a different die, which is why both grades appear in the same electrical table with two columns. On a channel that reports current to a host and takes action on it, the 0.5 per cent over temperature is the row to specify. On a channel that watches for a fault rather than measuring a value, the A grade is the cheaper answer and the B grade buys headroom the application never uses. The grade is the last letter of the part number and the first letter of the body marking.
Sixteen or thirty two volts of bus from one register bit
The bus conversion range of INA219BID is selected as 16 or 32 volts by one configuration bit, and the shunt full scale is selected as 40, 80, 160 or 320 millivolts by two more. The absolute maximum on the inputs is 26 volts, so the 32 volt range is a scaling choice rather than a rating and a bus that can ring above 26 volts needs a clamp.
The pairing matters in both directions. A 48 volt telecom rail cannot be measured directly and needs a divider, which puts its tolerance and its drift into the bus reading. A 12 volt rail on the 32 volt range loses one bit of resolution against the 16 volt range, and on a monitor whose bus accuracy is already 0.2 per cent typical that bit is small. Choose the range from the expected bus and leave the margin to the clamp rather than to the register.
Sixteen addresses and a calibration register
The address of INA219BID comes from two pins, each tied to ground, to the supply, to the data line or to the clock line, giving sixteen addresses from 0x40 to 0x4F. The calibration register converts the raw shunt code into amperes, and a power register then multiplies the current by the bus voltage.
The calibration value is where first builds usually go wrong, because the register also sets the current resolution and a value chosen for resolution can overflow at full load. The document's procedure starts from the largest current the channel will see and the shunt value, derives a range of possible current steps and asks for a round number inside it. A value picked by eye from a worked example for a different shunt is the failure mode, and it fails quietly: the reading wraps at high current rather than reporting a fault, which is read as a load problem.
Where a monitor with a bus replaces an amplifier and a converter
INA219BID is the right part when a host already has an I2C bus and the current reading is a number rather than a control signal. It reports current in amperes after calibration, reports bus voltage and power, and does the averaging in the part instead of in the host. On a server, a telecom shelf, a notebook or a charger, that is one package where a shunt amplifier and a converter used to sit.
It is the wrong part for a channel that has to feed an analogue loop, for a channel whose bandwidth is above a few kilohertz, and for a channel that cannot spare the 532 microseconds of a conversion. Our amplifier cross reference page covers the analogue alternatives, the converter cross reference page covers the external converter route, and the obsolete part cross reference hub covers the case where a tube code on a bill of materials has been withdrawn and the reel code has to be written in its place.
One milliamp, and a three volt floor
INA219BID runs from a single 3 to 5.5 volt supply and draws 1 milliamp maximum, which is twice what the INA209 draws and twenty times what a single current sense amplifier draws. The part is specified from minus 40 to plus 125 degrees, wider than the INA209, and it comes in an eight pin SOIC or an eight pin SOT-23 with the same electrical table.
The 3 volt floor is the row that decides whether the monitor can sit on the same rail it measures. It can measure a 3.3 volt rail while running from 3.3 volts, but not a 2.5 volt one, and a 1.8 volt rail needs the monitor on a separate supply. The supply also sets the logic levels on the bus, so a monitor on a 5 volt rail driving a 3.3 volt host needs a level check on the data line rather than an assumption that the pull up will sort it out.
For a pilot quantity of the tighter grade, the reel is the only active carrier and a distributor's cut is the usual route to a few hundred pieces. Our obsolete part cross reference hub covers that substitution, and the obsolescence management page covers the wider question of a grade that only exists on one carrier.
Is the B grade die still available? Yes, on the large reel as INA219BIDR. The tube row is the one marked obsolete.
Is the B grade worth the difference on a logging channel? Only if the log is used to make a decision: 0.5 per cent over temperature against 1 per cent is invisible in a trend and decisive in a protection threshold.