Contact Us

INA2133UA

Brand: Texas Instruments
Texas Instruments INA2133UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2133UA — Power Management & Signal Chain | Superb Automation

INA2133UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2133UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2133UA: the wider grade of the same fast dual, in the same tube

INA2133UA is the UA grade of the high speed dual difference amplifier in the fourteen pin SOIC, in a fifty piece tube, with 900 microvolts maximum of offset at plus and minus 15 volts and 1500 microvolts at plus and minus 5 volts. The rejection minimum is 74 dB, the gain error maximum is 0.1 per cent and the bandwidth is the family's 1.5 megahertz.

The UA grade is the wider sort, and the gap to the U grade is a factor of two on the offset column. On a 1 volt full scale signal 900 microvolts is 0.09 per cent, which is a 10 bit question, and 450 microvolts is 0.045 per cent, which is a 11 bit question. On a 100 millivolt signal both parts need a calibration and the grade is a price decision rather than an accuracy one.

INA2133UA as the vendor document publishes it

Channels2
Gain1 V/V, fixed
Supplyplus or minus 2.25 to plus or minus 18 volts, single 4.5 to 36 volts
Quiescent current0.95 milliamps typical, 1.2 maximum per amplifier
Offset, U grade150 microvolts typical, 450 maximum at plus and minus 15 volts
Offset, UA grade150 microvolts typical, 900 maximum at plus and minus 15 volts
Offset at plus and minus 5 volts300 typical with 750 maximum U, 1500 maximum UA
Offset drift2 microvolts per degree typical, 5 maximum
Rejection, U / UA80 minimum, 90 typical / 74 minimum, 90 typical decibels
Gain error, U / UA0.02 typical with 0.05 maximum / 0.1 maximum per cent
Gain nonlinearity, U / UA0.001 / 0.002 per cent of full scale range
Voltage noise57 nanovolts per root hertz on SHE, 20 on RFB
Bandwidth and slew1.5 megahertz, 5 volts per microsecond on SHE and 20 on RFB
Settling time4 microseconds to 0.1 per cent on a 10 volt step
Input impedance50 kilo-ohms differential, 25 kilo-ohms common mode
Temperature rangeminus 40 to plus 85 degrees specified
Vendor statusactive, fifty piece tube
Catalogue codeINA2133UA
Carriertube of 50
Lead finishprinted as a call to the vendor on this row
Moisture levellevel 3, 260 degrees, 168 hour floor life

Four hundred and fifty microvolts in the U grade, nine hundred in the UA

At plus and minus 15 volts the offset of INA2133UA is 150 microvolts typical and 450 maximum on the U grade, against 900 maximum on the UA grade, and at plus and minus 5 volts the same split reads 300 typical with 750 maximum against 1500. The drift is 2 microvolts per degree typical and 5 maximum, and the gain drift is 1 part per million per degree typical against 10 maximum.

The U and UA suffixes on this part are two sorts of the same die, and the A grade is the looser of the two by a factor of two on the offset column. The gain error follows the same pattern: 0.02 per cent typical and 0.05 maximum on the U grade against 0.1 maximum on the UA, with a gain nonlinearity of 0.001 per cent of full scale range against 0.002. On a 1 volt full scale that is 10 microvolts of nonlinearity against 20, which is a 16 bit question rather than a 12 bit one.

The same unity gain, at one and a half megahertz

INA2133UA is a dual difference amplifier with a fixed gain of 1 and a bandwidth of 1.5 megahertz, which is five times the bandwidth of the low power member of the family. The slew rate is 5 volts per microsecond on the SHE flow and 20 volts per microsecond on the RFB flow, and the settling time is 4 microseconds to 0.1 per cent on a 10 volt step.

The speed comes out of the quiescent current: 0.95 milliamps typical and 1.2 maximum per amplifier, against 160 microamps on the low power part. That is the whole trade in this pair. A channel that samples a shunt once per millisecond does not need 1.5 megahertz and should not pay for it, and a channel that has to follow a motor current through a switching cycle does need it and cannot use the slower part.

Common mode from twice the negative rail to twice the positive one

The input divider of INA2133UA puts the common mode window at 2 times the negative rail plus 3 volts at the bottom and 2 times the positive rail minus 3 volts at the top, so a part on a plus and minus 15 volt rail accepts plus and minus 33 volts of common mode and a part on plus and minus 5 volts accepts plus and minus 13 volts. The rejection is quoted at a source impedance of zero over that whole window.

The minimum is 80 dB on the U grade and 74 dB on the UA grade, with 90 dB typical on both, which at plus and minus 15 volts means a 30 volt common mode produces at most 3 millivolts of output error on the U grade and 6 millivolts on the UA. That is the row that separates the two grades in a real installation, more than the offset does, because a ground loop or a bus fault puts tens of volts on the input rather than microvolts.

Fifty kilo-ohms of input, one thousand picofarads of load

The differential input impedance of INA2133UA is 50 kilo-ohms and the common mode impedance is 25 kilo-ohms, both from the same 25 kilo-ohm resistors that set the gain, with a ratio match far tighter than the 20 per cent absolute tolerance. The output swings to within 1.5 volts of each rail at light load and within 0.8 volts into 100 kilo-ohms, and the part is stable into 1000 picofarads.

Those rows decide the source. A 1 kilo-ohm source into 50 kilo-ohms loses 2 per cent of its signal, which is more than the gain error of the part; a 10 kilo-ohm source loses 17 per cent. The load capacitance row is generous for a part with 1.5 megahertz of bandwidth, so a cable can hang directly on the output as long as it is terminated at the far end. The 4 microsecond settling time is what a multiplexed 16 channel scanner has to budget per channel.

Half a milliamp of quiescent current per channel, and the supplies it accepts

INA2133UA runs from a single supply of 4.5 to 36 volts or a split supply of plus and minus 2.25 to plus and minus 18 volts, and it draws 0.95 milliamps typical and 1.2 maximum per amplifier at plus and minus 15 volts, falling slightly to 0.92 typical at plus and minus 5 volts. The operating temperature range is minus 55 to plus 125 degrees and the specified range is minus 40 to plus 85.

Two documents disagree on that last row. The electrical table specifies the part from minus 40 to plus 85 degrees, while the package addendum prints the orderable rows from minus 55 to plus 125. A buyer who needs the wider window should ask for the qualification data rather than read the addendum column as a guarantee, and a buyer who is inside minus 40 to plus 85 is covered by the table.

Where the fast unity gain part belongs

INA2133UA belongs in a motor current sense that has to follow a pulse width modulated cycle, a differential to single ended converter in front of a fast sampling converter, a video or instrumentation line receiver, and any channel where a common mode of tens of volts has to be rejected without a transformer. The 1.5 megahertz and the 33 volt window are the two rows that make those applications work.

It does not belong in a battery instrument, where 1 milliamp per channel is the whole budget. It does not belong on a high impedance source, because 50 kilo-ohms loads it. It does not belong where gain is needed. And it does not belong in a channel that has to resolve microvolts, because 450 microvolts of offset on the U grade is a calibration step on every board. Our amplifier cross reference page covers the unity gain parts and their gains of 0.5 and 2, and the vendor consolidation page covers holding one grade across two boards.

The wider grade is the volume sort and the tighter one is the calibration sort. Our amplifier cross reference page covers both, and the vendor consolidation page covers one code across several boards.

What is the difference in rejection? 80 dB minimum on the U grade and 74 on the UA, with 90 dB typical on both.

Can both grades share a reel? Neither grade is published on a reel in this body, so both are tube parts and the question does not arise.