Contact Us

INA2128UA1K

Brand: Texas Instruments
Texas Instruments INA2128UA1K is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2128UA1K — Power Management & Signal Chain | Superb Automation

INA2128UA1K

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2128UA1K from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2128UA1K: the A grade on a thousand piece reel

INA2128UA1K is the A grade of the dual three op amp instrumentation amplifier in the sixteen pin SOIC on a 1000 piece large reel, the vendor string INA2128UA/1K. One thousand pieces is half the reel size this catalogue usually sees for a sixteen pin body, which makes the part a fit for a lower volume line rather than for a full production reel.

The electrical rows are the A grade's: 25 microvolts typical and 125 maximum of offset on the SHE flow, 110 dB minimum of rejection at a gain of 100, 700 microamps per channel and a moisture level of 2 with a one year floor life, the same as the tube. A line that moves from the tube to this reel changes its handling only in quantity, not in floor life.

INA2128UA1K as the vendor document publishes it

Channels2
Gain1 to 10000 V/V, 1 + 50 kilo-ohms / RG
Supplyplus or minus 2.25 to plus or minus 18 volts, 4.5 to 36 volts total
Quiescent current700 microamps per channel
Offset, plain code10 microvolts typical, 50 maximum on the SHE flow
Offset, A code25 microvolts typical, 125 maximum on the SHE flow
Offset drift, plain / A0.2 typical with 1 maximum / 2 maximum microvolts per degree
Input bias current2 typical with 5 maximum nanoamps on SHE, 0.15 with 0.7 on TID
Rejection at a gain of 180 minimum, 86 typical plain / 73 minimum, 86 typical A code
Rejection at a gain of 100120 minimum, 125 typical plain / 110 minimum, 125 typical A code
Voltage noise8 nanovolts per root hertz at 1 kilohertz on SHE, 6.9 on TID
Bandwidth1.3 megahertz at a gain of 1, 200 kilohertz at a gain of 100
Gain nonlinearity0.0003 typical, 0.004 maximum per cent of full scale range
Safe inputplus and minus 40 volts, no series resistor
Temperature rangeminus 40 to plus 85 degrees
Package16 pins, SOIC body DW
Vendor statusactive, 1000 piece large reel
Catalogue codeINA2128UA1K
Vendor stringINA2128UA/1K
Carrierlarge reel of 1000
Moisture levellevel 2, 260 degrees, one year floor life

Three op amps, one resistor, gain one to ten thousand

INA2128UA1K is a dual three op amp instrumentation amplifier with a gain law of 1 plus 50 kilo-ohms divided by the resistor between the gain pins, so one external resistor sets anything from 1 to 10000. A 50 kilo-ohm resistor gives 2, a 500 ohm resistor gives 101 and a 5 ohm resistor gives 10001, which is the top of the range.

The three op amp topology is what allows the gain to start at unity, where the two op amp family next to it in the catalogue starts at 5. The cost is two more amplifiers inside the package and a quiescent current of 700 microamps per channel, and the return is 1.3 megahertz of bandwidth at a gain of 1 and 200 kilohertz at a gain of 100, which is a wide front end for a part that draws under a milliamp per channel.

Eight nanovolts, and the noise that arrives with the source

The voltage noise of INA2128UA1K is 8 nanovolts per root hertz at 1 kilohertz on the SHE flow and 6.9 on the TID flow, with 10 nanovolts at 10 hertz and 0.2 microvolts peak to peak from 0.1 to 10 hertz. The current noise is 0.3 picoamps per root hertz on SHE and 0.17 on TID, which against a 10 kilo-ohm source is 3 nanovolts and against a 1 megaohm source is 300 nanovolts.

Read together, the two columns say that a low impedance bridge is limited by the 8 nanovolts and a high impedance sensor is limited by whatever current noise comes with the flow. The gain nonlinearity row is 0.0003 per cent typical and 0.004 maximum of full scale range on the A grade, which is small enough that a 16 bit converter sees the amplifier as linear and the resistor as the error. The 0.2 microvolts of low frequency noise is smaller than the 50 microvolt offset and does not enter a DC budget.

Fifty microvolts on the plain grade, one hundred and twenty five on the A grade

The offset of INA2128UA1K is printed twice, once for the plain code and once for the A code, and the A code is again the wider sort. INA2128U reads 10 microvolts typical and 50 microvolts maximum on the SHE flow, or 20 and 50 on the TID flow, and INA2128UA reads 25 typical and 125 maximum on SHE, 20 and 50 on TID. The drift rows follow: 0.2 microvolts per degree typical with 1 maximum on the plain code and 2 maximum on the A code.

Rejection separates the grades the same way. At a gain of 1 the plain code is 80 dB minimum and 86 typical against 73 and 86 on the A code, and at a gain of 100 the plain code is 120 dB minimum against 110. On a 10 millivolt load cell at a gain of 100, 50 microvolts is half a per cent and 125 is 1.25 per cent, so the grade is a calibration decision rather than a price decision.

Inputs that survive forty volts, and a window two volts inside each rail

The inputs of INA2128UA1K are protected to 40 volts beyond either rail with no series resistor, and the document prints the safe input voltage as plus and minus 40 volts at a source impedance of zero. The common mode window is two volts inside each rail, so a 15 volt rail gives plus and minus 13 volts, which covers a 4 to 20 milliamp loop and a bridge that sits at mid supply.

The differential input impedance is 10 gigaohms in parallel with 2 picofarads, and the common mode impedance is 100 gigaohms in parallel with 9 picofarads, so a 1 kilo-ohm series resistor pair adds a pole without loading the source. That is the practical way to keep a channel quiet next to a switching supply: the 40 volt protection means the resistor does not put the part at risk, and the 2 picofarads means the pole lands where the resistor puts it.

Bias current that depends on the chip flow, not on the grade

The input bias current of INA2128UA1K is the row where the two flows separate by a factor of ten. On the SHE flow the plain grade is 2 nanoamps typical and 5 maximum, and the A grade is 2 typical and 10 maximum. On the TID flow both grades read 0.15 nanoamps typical, with 0.7 maximum on the plain code and 1.4 on the A code.

That matters on a high impedance source rather than on a low one. A 1 megaohm thermistor or a pH electrode turns 10 nanoamps into 10 millivolts of offset, which is larger than the offset of either grade, and 0.7 nanoamps into 0.7 millivolts. Since the flow is not orderable, a channel with a source above about 100 kilo-ohms has to budget the SHE column, and the input offset current row, also 5 or 10 nanoamps on SHE against 0.7 and 1.4 on TID, is the one that decides the error rather than the bias current alone.

Where a three op amp dual belongs, and where it does not

INA2128UA1K belongs in an ECG or an EMG front end, a pressure or temperature transmitter, a weigh scale with a 2 millivolt per volt bridge, and an analog input module that scans eight channels through a multiplexer. The 120 dB of rejection at a gain of 100 is what a transmitter needs to sit on a 24 volt loop, and the 700 microamps per channel is what a loop powered device can afford.

It does not belong on a single 3.3 volt rail, because the total supply floor is 4.5 volts in single supply mode. It does not belong in a battery node that sleeps, because there is no shutdown pin. It does not belong in a chopper application, because 50 microvolts of offset with 0.5 microvolts per degree of drift is a different class from 25 microvolts with 0.1. Our amplifier cross reference page puts the grades and the alternatives on one table, and the vendor consolidation page covers holding one grade across several boards.

A thousand piece reel is a schedule commitment rather than a stock item. Our vendor consolidation page covers holding one reel across several boards, and the traceability report page covers the reel label.

Is the 1K reel the same moisture level as the tube? Yes, level 2 at 260 degrees with a one year floor life, so the handling rules do not change.

Why is the reel only a thousand pieces? The vendor publishes that reel size for the sixteen pin DW body, and the 2500 piece reel belongs to other families in this catalogue.