INA209AIPWR
Product Specifications
INA209AIPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA209AIPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA209AIPWR: the same monitor on a two thousand piece reel
INA209AIPWR is the INA209 monitor in the sixteen pin TSSOP on a 2000 piece large reel, which is the active carrier for this die. It measures a 0 to 26 volt bus from a 3 to 5.5 volt supply, draws 1.5 milliamps maximum, and is specified from minus 25 to plus 85 degrees, a narrower window than the current sense amplifiers in the same catalogue.
What the part adds over an amplifier and a converter is the arithmetic and the alerts: a calibration value turns codes into amperes, a second register multiplies current by bus voltage for watts, peak registers catch what polling misses, and an eight bit converter feeding a comparator trips the critical output in 5 microseconds. Every one of those has to be configured, which is the work a first article has to cover.
INA209AIPWR as the vendor document publishes it
| ADC resolution | 12 bits |
| Shunt least significant bit | 10 microvolts |
| Bus least significant bit | 4 millivolts |
| Shunt full scale | 40, 80, 160 or 320 millivolts, selected by the gain bits |
| Bus full scale | 16 or 32 volts, selected by one configuration bit |
| Bus input rating | 0 to 26 volts, absolute maximum 26 volts |
| Common mode rejection | 100 dB minimum, 120 typical |
| Offset voltage | 10 microvolts typical and 100 maximum at the narrowest range, 40 and 200 on the widest |
| Offset drift | 0.1 microvolts per degree |
| Power supply rejection | 10 microvolts per volt |
| Current measurement error | 0.2 per cent typical, 0.5 maximum, 1 per cent over temperature |
| Bus voltage measurement error | 0.2 per cent typical, 0.5 maximum, 1 per cent over temperature |
| Differential nonlinearity | 0.1 bit |
| Critical comparator path | 8 bit converter, 255 millivolt full scale, 1 millivolt steps, 5 microsecond delay |
| Critical comparator offset | 0.3 millivolts typical, 1.6 maximum |
| Addresses | 16, from 0x40 to 0x4F, set by two pins |
| Averaging | up to 128 samples in the part |
| Power down recovery | 40 microseconds |
| Supply range | 3 volts to 5.5 volts |
| Supply current | 1.5 milliamps maximum |
| Body | TSSOP, 16 pin, PW |
| Temperature range | minus 25 to plus 85 degrees |
| Vendor status | active, 2000 piece large reel |
| Catalogue code | INA209AIPWR |
| Vendor string | INA209AIPWR |
| Carrier | 2000 piece large reel |
| Moisture level | level 2, 260 degrees, one year floor life |
Sixteen addresses from two pins
The address of INA209AIPWR is set by tying the two address pins to ground, to the supply, to the data line or to the clock line. Four states on each pin give sixteen combinations, and the resulting addresses run from 0x40 to 0x4F. That is four times what a single resistor divider normally provides and it is enough for a supply with several rails on one bus.
The four states are worth thinking about before the board is released. Tying an address pin to the data or clock line puts the bus line's capacitance and its edges on a static input, which works but is the least forgiving of the four, and it means the address is decided by the bus rather than by a strap. Tying to ground and to the supply are the two clean states. A board that may carry eight of these should use the two clean states and a short strap pad for anything else, so the address can be changed without a resistor change.
Peak hold, and the calibration value that turns codes into amps
INA209AIPWR keeps the highest and lowest shunt reading in a pair of peak registers, keeps a separate peak for the bus voltage, and applies a calibration value to convert the shunt code into amperes. The calibration route exists so that the host does not have to multiply on every read, and it is the register most often wrong on a first build.
The arithmetic is set out in the document as a nine step procedure that starts from the maximum expected current and the shunt value and ends with a round current step. What the procedure is protecting against is overflow: a calibration value chosen for resolution rather than for range can overflow the current register at full load, and the reading then wraps rather than clips, which looks like a fault in the load rather than in the setting. Choose the step so the full scale is above the largest current the channel will ever see, then check the register at that current.
Twenty six volts of bus from a 3 volt supply
The supply of INA209AIPWR is 3 to 5.5 volts and the bus it measures runs from 0 to 26 volts, with the conversion range selected as 16 or 32 volts by a single register bit. The supply current is 1.5 milliamps maximum, and the part is specified from minus 25 to plus 85 degrees, which is a narrower window than the current sense amplifiers in the same catalogue and the row to check on an industrial build.
The 32 volt conversion range is a scaling range and not a rating. The absolute maximum on the inputs is 26 volts, so a bus that can ring above that needs a clamp or a divider, and a divider puts its own tolerance and drift into the bus reading. The same applies at the bottom: the bus channel is specified from zero, and the offset of that channel is what decides whether a 50 millivolt reading means 50 millivolts or nothing.
A twelve bit converter behind a four step gain stage
INA209AIPWR converts the shunt drop with a 12 bit converter whose least significant bit is 10 microvolts, in front of which sits a gain stage that selects a full scale of 40, 80, 160 or 320 millivolts. The bus voltage is converted on a second channel with a 4 millivolt bit, and the two results are multiplied in the background to give power.
The gain stage is the part most often set once and forgotten, and it should not be. At a full scale of 40 millivolts the offset is 10 microvolts typical and 100 maximum, and at 320 millivolts the same offset window is 40 and 200 microvolts, so the widest range carries the largest offset in absolute terms and the narrowest range carries the best resolution. A 20 amp channel on a 1 milliohm shunt develops 20 millivolts and belongs on the 40 millivolt range; a 20 amp channel on a 10 milliohm shunt develops 200 millivolts and belongs on the 320 millivolt range with four times the offset in microvolts and the same offset as a fraction of full scale.
An eight bit converter that trips in five microseconds
Alongside the 12 bit measurement path, INA209AIPWR carries an eight bit digital to analogue converter with a 255 millivolt full scale and 1 millivolt steps, feeding a comparator whose output drives the critical alert pin. The comparator delay is 5 microseconds, which is the fastest response the part offers and the reason the path exists at all: a conversion and an interrupt take hundreds of microseconds, and a short circuit does not wait.
Two rows decide whether that path is usable. The comparator offset is 0.3 millivolts typical and 1.6 maximum, which on 1 millivolt steps is a step and a half of uncertainty and has to be part of the trip point. The DAC accuracy is 0.5 per cent typical and 1 maximum of its own full scale, which is 2.5 millivolts at the top of the range. A channel that sets the trip at 200 millivolts therefore has to allow a few millivolts of window, and a channel that sets it near 1 millivolt is using the first step as a comparator rather than as a threshold.
What a monitor with a converter does that a shunt amplifier cannot
INA209AIPWR replaces a shunt amplifier, a converter and the arithmetic between them. It reports current in amperes after a calibration value has been written, it reports power in watts without host work, it keeps peaks that a polling loop would miss, and it raises an alert in hardware when a threshold is crossed. The cost is that every one of those functions has to be configured, and a configuration left at its default reports codes rather than amps.
It is the wrong part for a channel that has to be read by an analogue comparator, for a channel with a bandwidth above a few kilohertz, and for a channel where a single register write is not available at start up. Our amplifier cross reference page lists the analogue parts that sit beside it, the converter cross reference page covers the external converter route, and the incoming inspection plan covers the register check on the first article.
The reel is the carrier a line needs and the register set is what the first article has to prove. Our incoming inspection plan covers that first article check, and the converter cross reference page covers the external converter route where the monitor does not fit.
How many of these can share one bus? Sixteen, at addresses 0x40 to 0x4F, with the two address pins each tied to ground, supply, data or clock.
How fast can the critical alert respond? The comparator path is 5 microseconds, while a conversion at 12 bits with averaging takes hundreds of microseconds, so the alert is the fast path and the registers are the logging path.