Contact Us

INA209AIPW

Brand: Texas Instruments
Texas Instruments INA209AIPW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA209AIPW — Power Management & Signal Chain | Superb Automation

INA209AIPW

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA209AIPW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA209AIPW: the sixteen pin power monitor in a tube that reads obsolete

INA209AIPW is the INA209 current and power monitor in the sixteen pin TSSOP, in a tube. The part converts a shunt drop with a 12 bit converter behind a four step gain stage, converts the bus voltage on a second channel, multiplies the two for power, keeps peak registers and raises hardware alerts through an eight bit converter and a comparator.

The tube is the row to read before ordering. The addendum read for this page prints INA209AIPW with the status Obsolete and no packing quantity, while INA209AIPWR, the same body on a 2000 piece large reel, is active. The electrical content stays on this page because the die is in production, and the carrier position is stated in the table rather than glossed over.

INA209AIPW as the vendor document publishes it

ADC resolution12 bits
Shunt least significant bit10 microvolts
Bus least significant bit4 millivolts
Shunt full scale40, 80, 160 or 320 millivolts, selected by the gain bits
Bus full scale16 or 32 volts, selected by one configuration bit
Bus input rating0 to 26 volts, absolute maximum 26 volts
Common mode rejection100 dB minimum, 120 typical
Offset voltage10 microvolts typical and 100 maximum at the narrowest range, 40 and 200 on the widest
Offset drift0.1 microvolts per degree
Power supply rejection10 microvolts per volt
Current measurement error0.2 per cent typical, 0.5 maximum, 1 per cent over temperature
Bus voltage measurement error0.2 per cent typical, 0.5 maximum, 1 per cent over temperature
Differential nonlinearity0.1 bit
Critical comparator path8 bit converter, 255 millivolt full scale, 1 millivolt steps, 5 microsecond delay
Critical comparator offset0.3 millivolts typical, 1.6 maximum
Addresses16, from 0x40 to 0x4F, set by two pins
Averagingup to 128 samples in the part
Power down recovery40 microseconds
Supply range3 volts to 5.5 volts
Supply current1.5 milliamps maximum
BodyTSSOP, 16 pin, PW
Temperature rangeminus 25 to plus 85 degrees
Vendor statusobsolete in the package addendum, no packing quantity printed
Catalogue codeINA209AIPW
Vendor stringINA209AIPW, obsolete; INA209AIPWR is the active row
Carriertube
Moisture levellevel 3, 260 degrees, 168 hour floor life

A twelve bit converter behind a four step gain stage

INA209AIPW converts the shunt drop with a 12 bit converter whose least significant bit is 10 microvolts, in front of which sits a gain stage that selects a full scale of 40, 80, 160 or 320 millivolts. The bus voltage is converted on a second channel with a 4 millivolt bit, and the two results are multiplied in the background to give power.

The gain stage is the part most often set once and forgotten, and it should not be. At a full scale of 40 millivolts the offset is 10 microvolts typical and 100 maximum, and at 320 millivolts the same offset window is 40 and 200 microvolts, so the widest range carries the largest offset in absolute terms and the narrowest range carries the best resolution. A 20 amp channel on a 1 milliohm shunt develops 20 millivolts and belongs on the 40 millivolt range; a 20 amp channel on a 10 milliohm shunt develops 200 millivolts and belongs on the 320 millivolt range with four times the offset in microvolts and the same offset as a fraction of full scale.

Twenty six volts of bus from a 3 volt supply

The supply of INA209AIPW is 3 to 5.5 volts and the bus it measures runs from 0 to 26 volts, with the conversion range selected as 16 or 32 volts by a single register bit. The supply current is 1.5 milliamps maximum, and the part is specified from minus 25 to plus 85 degrees, which is a narrower window than the current sense amplifiers in the same catalogue and the row to check on an industrial build.

The 32 volt conversion range is a scaling range and not a rating. The absolute maximum on the inputs is 26 volts, so a bus that can ring above that needs a clamp or a divider, and a divider puts its own tolerance and drift into the bus reading. The same applies at the bottom: the bus channel is specified from zero, and the offset of that channel is what decides whether a 50 millivolt reading means 50 millivolts or nothing.

Peak hold, and the calibration value that turns codes into amps

INA209AIPW keeps the highest and lowest shunt reading in a pair of peak registers, keeps a separate peak for the bus voltage, and applies a calibration value to convert the shunt code into amperes. The calibration route exists so that the host does not have to multiply on every read, and it is the register most often wrong on a first build.

The arithmetic is set out in the document as a nine step procedure that starts from the maximum expected current and the shunt value and ends with a round current step. What the procedure is protecting against is overflow: a calibration value chosen for resolution rather than for range can overflow the current register at full load, and the reading then wraps rather than clips, which looks like a fault in the load rather than in the setting. Choose the step so the full scale is above the largest current the channel will ever see, then check the register at that current.

What a monitor with a converter does that a shunt amplifier cannot

INA209AIPW replaces a shunt amplifier, a converter and the arithmetic between them. It reports current in amperes after a calibration value has been written, it reports power in watts without host work, it keeps peaks that a polling loop would miss, and it raises an alert in hardware when a threshold is crossed. The cost is that every one of those functions has to be configured, and a configuration left at its default reports codes rather than amps.

It is the wrong part for a channel that has to be read by an analogue comparator, for a channel with a bandwidth above a few kilohertz, and for a channel where a single register write is not available at start up. Our amplifier cross reference page lists the analogue parts that sit beside it, the converter cross reference page covers the external converter route, and the incoming inspection plan covers the register check on the first article.

Sixteen addresses from two pins

The address of INA209AIPW is set by tying the two address pins to ground, to the supply, to the data line or to the clock line. Four states on each pin give sixteen combinations, and the resulting addresses run from 0x40 to 0x4F. That is four times what a single resistor divider normally provides and it is enough for a supply with several rails on one bus.

The four states are worth thinking about before the board is released. Tying an address pin to the data or clock line puts the bus line's capacitance and its edges on a static input, which works but is the least forgiving of the four, and it means the address is decided by the bus rather than by a strap. Tying to ground and to the supply are the two clean states. A board that may carry eight of these should use the two clean states and a short strap pad for anything else, so the address can be changed without a resistor change.

An eight bit converter that trips in five microseconds

Alongside the 12 bit measurement path, INA209AIPW carries an eight bit digital to analogue converter with a 255 millivolt full scale and 1 millivolt steps, feeding a comparator whose output drives the critical alert pin. The comparator delay is 5 microseconds, which is the fastest response the part offers and the reason the path exists at all: a conversion and an interrupt take hundreds of microseconds, and a short circuit does not wait.

Two rows decide whether that path is usable. The comparator offset is 0.3 millivolts typical and 1.6 maximum, which on 1 millivolt steps is a step and a half of uncertainty and has to be part of the trip point. The DAC accuracy is 0.5 per cent typical and 1 maximum of its own full scale, which is 2.5 millivolts at the top of the range. A channel that sets the trip at 200 millivolts therefore has to allow a few millivolts of window, and a channel that sets it near 1 millivolt is using the first step as a comparator rather than as a threshold.

A tube of sixteen pin parts is a prototype quantity, and the reel is what a line needs. Our obsolete part cross reference hub covers the carrier substitution, and the incoming inspection plan covers the register check on the first article.

Can the tube code still be bought? Stock already in the channel can be, but the addendum marks the row obsolete with no packing quantity, so a plan that depends on replenishment should name the reel code.

Is the reel part electrically identical? Yes. INA209AIPWR is the same body and the same die on a 2000 piece large reel at moisture level 2 with a one year floor life.