Contact Us

ADS1120IPWR

Brand: Texas Instruments
Texas Instruments ADS1120IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS1120IPWR — Power Management & Signal Chain | Superb Automation

ADS1120IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS1120IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS1120IPWR: 16-bit 2 kSPS delta-sigma converter in a 16-pin TSSOP

ADS1120IPWR is the small-signal converter that replaces a separate PGA, reference and excitation source on a sensor board in a TSSOP body of 16 pins. The part carries two differential or four single-ended inputs, a gain stage to 128, a 2.048 V reference, two matched current sources, an oscillator and a temperature sensor in one 16-pin body, so the analogue front end for an RTD or a bridge collapses into one footprint. Supply range is 2.3 V to 5.5 V on both the analogue and the digital rail, and conversions run to 2000 samples per second.

Order code and package

Order codeADS1120IPWR
Function4-channel, 2 kSPS, 16-bit converter with gain stage and reference
InterfaceSPI mode 1, four wire
Inputstwo differential or four single-ended, multiplexed
Referenceinternal 2.048 V, 5 ppm per C typical drift
Excitationtwo matched current sources, 50 microamps to 1.5 mA
Oscillatorinternal, 2 percent accuracy, no crystal needed
Temperature sensorinternal, 0.5 C typical accuracy
PackageTSSOP, 16 pins, 5.00 mm by 4.40 mm
Temperature rangeminus 40 to plus 125 C
Supply2.3 to 5.5 V, analogue and digital
DatasheetSBAS535 revision H

Electrical parameters that decide the application

Resolution16 bits, with 16 noise-free bits quoted at 20 samples per second
Data rateup to 2000 samples per second, single cycle settling at every rate
Mains rejectionsimultaneous 50 Hz and 60 Hz rejection at 20 samples per second
Gain1 to 128, programmable
Supply currentas low as 120 microamps in duty-cycle mode with the gain stage bypassed
Reference drift5 ppm per C typical, which is 512 microvolts over the full 125 C span on 2.048 V
Input rangelimited to the supply span minus 0.4 V divided by the gain when the gain stage is on
Excitation matchthe two current sources are matched to each other, which is what makes a three-wire RTD lead compensation work
Digital supplyseparate DVDD, so a 3.3 V host can sit beside a 5 V analogue rail
Package thermalTSSOP 16 on a small board area, so the copper under the part sets the self heating

Points to check before this part goes on a BOM

The 16 noise-free bits belong to 20 samples per second, not to the headline 2000. At the top rate the effective resolution falls by roughly four bits, so a product that quotes 16 bits and then runs at 2 kSPS is quoting two different operating points.

The gain stage input range is not the rail. With gain on, the usable input is the analogue span minus 0.4 V divided by the gain, so a 3.3 V board at gain 128 has about 22.6 mV of headroom per side, and a bridge that swings 30 mV clips before the converter does.

The internal reference drifts 5 ppm per C typical over a 125 C span, which is 512 microvolts on 2.048 V, or 0.025 percent of full scale. A ratiometric bridge measurement cancels that term because the bridge and the reference share a supply; an absolute measurement does not.

Two matched current sources are the reason a three-wire RTD works without a lead resistance error, but they have to be routed on separate pins with equal trace resistance. Sharing one source between two channels reintroduces the lead drop the part was bought to remove.

Duty-cycle mode at 120 microamps is a mode, not a state. The converter wakes, converts and sleeps, so the effective sample rate is set by the duty cycle and the host has to accept the latency that comes with it.

The oscillator is 2 percent accurate, which is fine for a data rate and not fine for a time base. Timestamped measurements need an external clock or a host-side correction.

Where this order code fits

Boards weighing this converter against a 24-bit part usually start from the resolution the sensor actually needs rather than the bit count. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the 16-bit figure the same at every data rate? No. The 16 noise-free bits are quoted at 20 samples per second; the noise rises as the data rate rises, and the effective resolution at 2 kSPS is several bits lower.

Can the part run from a single 3.3 V rail? Yes. AVDD and DVDD both accept 2.3 V to 5.5 V, and the internal reference stays at 2.048 V, so the input range is set by the gain and not by the rail.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.