AMC1301DWVR
Product Specifications
AMC1301DWVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The AMC1301DWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AMC1301DWVR: reinforced isolated amplifier with a 250 mV input and 0.2 mV offset
AMC1301DWVR is the current sense stage where the barrier has to be reinforced rather than basic in a SOIC body of 8 pins. The part amplifies a plus or minus 250 mV shunt signal across a barrier rated 7070 V peak reinforced per DIN EN IEC 60747-17 and 5000 V RMS for one minute per UL1577, with a working voltage of 1 kV RMS. Gain is 8.2, offset error is 0.2 mV maximum, offset drift is 3 microvolts per C maximum and gain drift is 50 ppm per C maximum.
Order code and package
| Order code | AMC1301DWVR |
| Function | isolated amplifier, gain 8.2, 250 mV input |
| Isolation | 7070 V peak reinforced per DIN EN IEC 60747-17, 5000 V RMS one minute per UL1577 |
| Working voltage | 1 kV RMS |
| Offset | 0.2 mV maximum |
| Offset drift | 3 microvolts per C maximum |
| Gain error | 0.3 percent maximum |
| Gain drift | 50 ppm per C maximum |
| Package | SOIC, 8 pins, wide body |
| Temperature range | minus 40 to plus 125 C |
| Datasheet | SBAS654 revision G |
| Grade variant | AMC1301S moves the offset drift to 4 microvolts per C and the gain drift to 60 ppm |
Electrical parameters that decide the application
| Nonlinearity | 0.03 percent maximum |
| Offset | 0.2 mV maximum, 0.08 percent of the 250 mV input range |
| Offset drift | 3 microvolts per C maximum, 375 microvolts over the 125 C span |
| Gain drift | 50 ppm per C maximum, 6250 ppm over the span, which is the larger of the two drift terms |
| Isolation | reinforced rather than basic, which is the difference between a functional barrier and a safety barrier |
| Working voltage | 1 kV RMS continuous |
| Supply | 3.0 to 5.5 V on both sides |
| Input | either input pin needs a DC path to the high side ground to define the common mode |
| Bandwidth | set for motor and converter current loops |
| Package | wide body SOIC 8, 5.85 mm by 7.50 mm |
Points to check before this part goes on a BOM
Gain drift at 50 ppm per C is 6250 ppm over the 125 C span, or 0.625 percent, which is twice the initial gain error of 0.3 percent. On a stage that is calibrated at 25 C, the drift term is what limits the current reading at the temperature extremes.
Zero point two millivolts of maximum offset is 0.08 percent of the 250 mV range and, at a 1 mOhm shunt, 0.2 A of apparent current. It is small enough to calibrate out and large enough that skipping the calibration shows up as a state of charge error on a battery product.
Reinforced isolation is the reason this part costs more than the 4000 V peak member of the family. Reinforced is a safety rating that allows the barrier to be the only protection, while basic isolation assumes a second barrier somewhere in the system.
Either input pin needs a DC path to the high side ground. A floating shunt with no path leaves the common mode undefined and the output drifts to a rail, which reads as a current that is not there.
The S variant trades offset drift and gain drift for something else in the same document, so a BOM that swaps the two suffixes is swapping accuracy terms, not just grades.
Working voltage of 1 kV RMS continuous is what a 800 V bus is checked against, and the 7070 V peak withstand figure is a test, not an operating point.
Where this order code fits
Servo and charger current loops use this part where the barrier is part of the safety case rather than a functional separation. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
What does reinforced isolation add? It is a safety rating that allows the barrier to be the only insulation between the bus and the controller, where basic isolation assumes a second barrier.
Which error dominates at temperature? Gain drift, at 0.625 percent over the full span, against 0.3 percent of initial gain error and 0.08 percent of offset.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.