INA185A2IDRLR
Product Specifications
INA185A2IDRLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA185A2IDRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA185A2IDRLR: bidirectional current sense in a 1.6 mm by 1.6 mm body
The INA185 is a bidirectional current sense amplifier in a six pin SOT-563 package that measures 1.6 mm by 1.6 mm by 0.55 mm, with a common mode range to 26 V and a 2.7 V to 5.5 V supply. The A2 member has a gain of 50 V/V, and the family covers 20, 50, 100 and 200 V/V so a circuit can pick the gain that uses the converter range. Offset is 25 microvolts typical, gain error is 0.05 per cent on the A1 to A3 members and 0.07 per cent on the A4, and the bandwidth is 350 kHz at the lowest gain, falling to 210 kHz at this one.
Bidirectional means the reference pin sets the zero current level away from ground, so a charge and a discharge current both produce a positive output swing either side of that reference. That is what a battery gauge or a motor phase needs, and it is the difference between this family and the unidirectional monitors that read only one direction. The six pin body leaves room for the reference pin without growing the package, which is why the part sits inside a phone, a drone or a battery pack where the board area is the constraint.
Key data for the INA185A2IDRLR
| Gain | 50 V/V fixed, with 20, 100 and 200 V/V members in the same body and the same footprint |
| Direction | Bidirectional through the reference pin, so charge and discharge both read inside the output range |
| Common mode | Up to 26 V, independent of the 2.7 V to 5.5 V supply, low side or high side placement |
| Offset | 25 microvolts typical, gain error 0.05 per cent on the A1 to A3 members and 0.07 per cent on the A4 |
| Bandwidth | 210 kHz at a gain of 50, 350 kHz at a gain of 20, 150 kHz at 100 and 105 kHz at 200 |
| Supply | 2.7 V to 5.5 V, quoted with the reference at half the supply for a centred bidirectional range |
Body, marking and reel data
| Body | DRL, SOT-563 6 pin, 1.6 mm by 1.6 mm by 0.55 mm, the smallest body in this family |
| Reel | 4000 pieces on a large reel for the DRL body, 250 piece small reel on the T suffix |
| Marking | 1DW on the A2 row of the DRL body, four characters on a package smaller than a grain of rice |
| Status | The plain INA185A2IDRLR row prints obsolete in the addendum while the .B row of the same string prints active |
Where the smallest body decides the part
On a battery pack or a drone flight controller, the current monitor sits inside a space that is already full, and a 1.6 mm square body with three pins on a side fits between the shunt and the connector. The alternative is a larger package on the other side of the board, which puts the sense traces next to the switching node and turns the measurement into an antenna. Size is therefore not a cosmetic choice on this part: it decides whether the sense pair can be kept short and whether the reference can be tied to a quiet node.
Typical uses are battery management, motor phase current in a small drive, USB power delivery and portable instrumentation. Where a customer's board was written for the DRL body, the current status has to be checked before a production order is placed, because the plain row prints obsolete and the active row of the same string prints against a different body. Our obsolescence management page covers how we handle a string in that state, and the power management cross reference lists the bidirectional monitors by body size.
Buyer questions on the INA185A2IDRLR
Is the part still available in the DRL body? The addendum prints the plain INA185A2IDRLR row as obsolete and the .B row of the same string as active against the SC70 body. That means a purchase order has to name the body and be confirmed with the vendor before a schedule is promised, rather than being placed from the catalogue line.
How is the zero current level set? The reference pin is driven from a divider or a reference, and the output sits at that level at zero current. Half the supply is the usual choice because it gives equal swing in both directions.
Does it work on the low side? Yes, the common mode range extends to ground on the low side and the part is specified for both placements. The difference is the common mode the amplifier sees, not the transfer function.
Availability and ordering notes
The 4000 piece reel is the production packing for the DRL body. Given the status of the plain row, every order for this string is confirmed against the current addendum before it is booked, and the .B row is quoted with the body it actually ships. That check is part of the supplier scorecard we keep for the lines we buy most often, so a status change is caught before a customer's build is affected.