OP27GSZ-REEL7
Product Specifications
OP27GSZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The OP27GSZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
OP27GSZ-REEL7: the precision op amp that is now marked not recommended for new builds
What this order code is
OP27GSZ-REEL7 is the SOIC-8 body of the OP27, a low noise precision operational amplifier that combines a 10 microvolt typical offset with 3 nanovolts per root hertz of voltage noise and 0.2 microvolts per degree C of drift. Analog Devices marks the family as not recommended for new builds, which is a status and not a stock position: the part is still produced and still bought, and every large inventory of legacy instrumentation boards still lists it.
The amplifier uses bias current cancellation, so the input bias current is plus or minus 10 nA rather than the tens of nanoamps a plain bipolar input would show, and the output stage is specified to swing plus or minus 10 V into 600 ohms. Open loop gain is 1.8 million, common mode rejection is 126 dB at plus or minus 11 V of common mode, and both supply rejection and common mode rejection exceed 120 dB. Long term drift is quoted at 0.2 microvolts per month.
Parameters as published
| Item | Value |
|---|---|
| Voltage noise density | 3 nV per root hertz, 3.5 nV at 10 Hz |
| Low frequency noise | 80 nV peak to peak, 0.1 Hz to 10 Hz |
| Offset voltage | 10 microvolts typical, 25 microvolts maximum |
| Offset drift | 0.2 microvolts per degree C typical, 0.6 maximum |
| Input bias current | plus or minus 10 nA, cancellation network |
| Gain bandwidth | 8 MHz |
| Slew rate | 2.8 V per microsecond |
| Open loop gain | 1.8 million |
| Common mode rejection | 126 dB at plus or minus 11 V |
| Output swing | plus or minus 10 V into 600 ohms |
| Long term drift | 0.2 microvolts per month |
| Package and status | 8-lead SOIC, reel of 7 inch, not recommended for new builds |
Numbers that decide the application
Three nanovolts per root hertz over a 10 kHz band is 0.3 microvolts rms, and over 100 kHz it is 0.95 microvolts rms. Against a 16 bit converter on a 5 V range, where one count is 76.3 microvolts, the noise is 0.004 and 0.012 of a count, so the amplifier is not the noise limit at 16 bits over those bands. The 10 microvolt typical offset is 0.13 of a count and the 25 microvolt maximum is 0.33 of a count, so a full 16 bit budget can be closed on offset alone without trimming.
Drift is where the arithmetic changes. The 0.6 microvolt per degree C maximum over the 125 degree industrial span is 75 microvolts, which is 0.98 of a 16 bit count on 5 V. That figure sits inside the budget but it uses the whole of it, so a circuit that needs 16 bits of absolute accuracy over temperature has no room for a second drift term. The 0.2 microvolt per month long term drift is 2.4 microvolts a year, an order of magnitude below the offset.
At a gain of 100 the 8 MHz gain bandwidth product leaves 80 kHz of closed loop bandwidth, and the 2.8 V per microsecond slew rate limits a 10 V peak to peak output to 89 kHz, so the two numbers meet in the same place and neither is the clear limit. Input bias current of 10 nA is 10 millivolts across a 1 megohm source and 100 microvolts across 10 kilohms, which is the reason this amplifier belongs behind a low impedance source: with 1 megohm in front of it the bias current is a hundred times the offset.
Selection and cross reference notes
The status line is the first thing to read on any quotation. A part marked not recommended for new builds can still be the right answer for a form, fit and function replacement on an existing board, and it is the wrong answer for a new platform where the qualification cycle will outlive the supply. Both decisions are legitimate, but they are different decisions and the code alone does not tell you which case you are in.
When a replacement is being evaluated, the parameters that must match first are the offset, the drift, the noise density and the package pinout, in that order. A part with better noise and worse drift is not a substitute on a 16 bit channel, and a part with a lower offset in a different package is a board change rather than a replacement. The 600 ohm load specification is also worth checking, because an amplifier that matches on noise but not on drive will not hold plus or minus 10 V into the same load.
Where it fits
Low level amplification ahead of a data converter is the classic use: instrumentation front ends, precision summing amplifiers, stable integrators, threshold detectors and professional audio input stages. The vendor names tape head and microphone preamplifiers in the same list. These are all cases where the source impedance is low enough that the bias current stays well below the offset, and where the 8 MHz bandwidth is used at a gain of 10 to 100 rather than at unity. Buyers comparing against other precision amplifiers can work from the amplifier cross reference page, and teams replacing a part that has moved to end of life usually start at the obsolete part cross reference hub.
Buying notes
OP27 is a part where the letter and the package decide the grade: G is the commercial grade body, S is the SOIC, Z is the lead free finish, and REEL7 is the 7 inch reel. A quotation that names OP27 without those fields is not a quotation for this line. Counterfeit OP27 die in re marked packages is a known problem on this family, so date code, packaging and a traceable source are worth more here than a lower unit price.
Sourcing notes and next step
We hold and quote OP27 codes and check the grade, body and finish fields against the order line. Where the exact code is gone, the answer is either a verified equivalent with the offset, drift and package compared line by line, or a statement that there is none. Send the code, the quantity and the annual usage through the obsolete part hub and we will come back with what is available and what the alternatives actually differ in.
Request Quote — In Stock, 100% New & Original, Full Warranty