INA181A2IDBVR
Product Specifications
INA181A2IDBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA181A2IDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA181A2IDBVR: a 50 V/V current sense amplifier on a 3000 piece reel
INA181A2IDBVR is the 50 V/V member of a bidirectional current sense amplifier family, in the six pin SOT-23 on a 3000 piece large reel. Common mode runs from minus 0.2 to plus 26 volts independent of the supply, the supply is 2.7 to 5.5 volts, the quiescent current is 195 microamps typical, the bandwidth is 210 kHz at this gain, and the gain error is 1 per cent maximum over temperature.
The R suffix is the carrier and it is the one most builds actually buy: 3000 pieces on a 178 millimetre reel, which is a feeder rather than a stick. The part is a cost optimised monitor, so the rows that matter are not the typical ones but the maximums over minus 40 to plus 125 degrees, and those are what the table on this page carries.
INA181A2IDBVR as the vendor document publishes it
| Gain | 50 V/V |
| Common mode range | minus 0.2 to plus 26 volts, independent of the supply |
| Supply range | 2.7 to 5.5 volts |
| Common mode rejection | 84 dB minimum, 100 typical |
| Offset at zero common mode | 25 microvolts typical, 150 maximum |
| Offset at 12 volts of common mode | 100 microvolts typical, 500 maximum |
| Offset drift | 0.2 microvolts per degree typical, 1 maximum |
| Supply rejection | 8 microvolts per volt typical, 40 maximum |
| Input bias current | 6 microamps at zero common mode, 75 at twelve volts |
| Gain error | 0.1 per cent typical, 1 maximum over temperature |
| Gain drift | 1.5 ppm per degree typical, 20 maximum |
| Nonlinearity | 0.01 per cent |
| Bandwidth | 210 kHz with a 10 picofarad load |
| Slew rate | 2 volts per microsecond |
| Voltage noise | 40 nanovolts per root hertz |
| Output swing to supply | within 20 millivolts typical, 30 maximum into 10 kohm |
| Output swing to ground | within 0.5 millivolts typical, 5 maximum |
| Quiescent current | 195 microamps typical, 260 maximum, 300 over temperature |
| Stable load capacitance | 1 nanofarad |
| Body | six pin SOT-23 or SC70 |
| Temperature range | minus 40 to plus 125 degrees |
| Catalogue code | INA181A2IDBVR |
| Vendor string | INA181A2IDBVR |
| Carrier | 3000 piece large reel, 178 mm |
| Body | SOT-23, DBV, six pin |
Four fixed gains: 20, 50, 100 and 200
INA181A2IDBVR is one of four gain options in a single current sense amplifier family, and the letter after the A is the gain: A1 is 20 V/V, A2 is 50, A3 is 100 and A4 is 200. All four share the same die, the same six pin bodies and the same 2.7 to 5.5 volt supply, so the choice is made once, from the shunt value and the converter range, and does not change anything else on the board.
The choice is arithmetic. A 10 milliohm shunt carrying 5 amps develops 50 millivolts, which at a gain of 50 is 2.5 volts and fills a 3.3 volt converter's range; the same shunt with a gain of 20 gives 1 volt and wastes two thirds of the range; with a gain of 200 it gives 10 volts and clips. Because the gain error is 1 per cent maximum at every option, the gain does not buy accuracy, only scale, and the option with the largest signal at the converter is always the right one.
Minus 0.2 to plus 26 volts of common mode on a 5 volt supply
The common mode range of INA181A2IDBVR is minus 0.2 to plus 26 volts, independent of the supply, which is what allows a 26 volt bus to be measured by a part running from 3.3 volts. The negative end matters as much as the positive one: minus 0.2 volts means the amplifier still works when the shunt is on the low side and the ground return lifts by a diode drop or by the voltage across a trace, and it means a bidirectional measurement can swing through zero without a dead band.
Rejection over that window is 84 dB minimum and 100 typical, measured with the inputs at 0 to 26 volts and no differential signal. That is a lower figure than a dedicated high voltage monitor publishes, and it is the row that decides whether a 26 volt bus with 1 volt of ripple can be measured to 1 per cent: 1 volt of ripple divided by 10 to the 4.2 is 63 microvolts at the input, which at a gain of 50 is 3 millivolts at the output against a 2.5 volt full scale, 0.13 per cent. It is the switching transients rather than the ripple that usually break that budget.
One hundred and fifty microvolts at zero common mode, five hundred at twelve volts
The offset of INA181A2IDBVR is quoted twice because it depends on the common mode: 25 microvolts typical and 150 maximum with the inputs at zero volts, 100 and 500 microvolts with the inputs at 12 volts. Drift is 0.2 microvolts per degree typical and 1 maximum, supply rejection is 8 microvolts per volt typical and 40 maximum, and the input bias current is 6 microamps at zero common mode rising to 75 microamps at 12 volts, with 0.05 microamps of offset current.
The bias current row is the one that surprises people. 75 microamps flowing in the shunt's own resistance is 75 microvolts across a 1 milliohm shunt, which at a gain of 50 is 3.75 millivolts at the output and 0.15 per cent of a 2.5 volt full scale, and it changes with common mode rather than staying constant. On a shunt below a milliohm that term is comparable with the offset, and it is why the vendor's board guidance asks for the input traces to be matched and kept away from the shunt's Kelvin connections.
One per cent of gain error, and what it costs a current reading
Gain error on INA181A2IDBVR is 0.1 per cent typical and 1 per cent maximum over minus 40 to plus 125 degrees, with 1.5 ppm per degree typical and 20 maximum of gain drift and 0.01 per cent of nonlinearity. The 1 per cent is a maximum over temperature rather than at 25 degrees, which is the figure a specification should quote, and the drift row is the part that a single point calibration cannot remove.
What 1 per cent means depends on where the channel sits in its range. At full scale it is 1 per cent of the reading. At a tenth of full scale it is still 1 per cent of the reading and the offset becomes the larger term: 150 microvolts of offset at a gain of 50 is 7.5 millivolts at the output, which against a 250 millivolt reading is 3 per cent. That is why a current monitor is specified over a range rather than at a point, and why the shunt is chosen to put the working current near the top of the amplifier's range rather than in the middle.
350 kHz at 20, 105 kHz at 200
Bandwidth on INA181A2IDBVR falls with the gain option: 350 kHz for A1, 210 kHz for A2, 150 kHz for A3 and 105 kHz for A4, all with a 10 picofarad load, with a slew rate of 2 volts per microsecond and 40 nanovolts per root hertz of input referred noise. Output swing is within 20 millivolts of the positive rail typical and 30 maximum into a 10 kohm load, and within 0.5 to 5 millivolts of ground, which is what makes a 3.3 volt rail usable from end to end.
For a motor or a battery current that bandwidth is more than enough, and for a switching supply it is the number that decides whether the monitor sees the ripple or the average. At 350 kHz a 100 kHz switching ripple is passed with a few degrees of phase shift; at 105 kHz it is attenuated, and a current loop closed through the monitor then has a pole it did not expect. The noise figure translates the same way: 40 nanovolts per root hertz over a 100 kHz bandwidth is 12.6 microvolts RMS, which at a gain of 200 is 2.5 millivolts at the output.
SOT-23, SC70 and the automotive flow
INA181A2IDBVR comes in two six pin bodies: the DBV, which is the SOT-23 at 2.9 by 2.8 millimetres, and the DCK, the SC70 at 2.0 by 2.1. The die is the same and the pinout is nearly the same, but the thermal resistance is not: 188 degrees per watt for the SOT-23 against 198 for the SC70 on the single channel, and the reel quantities differ between the grades, which is why the body and the carrier belong on the order line rather than in a note.
The Q1 suffix marks the automotive flow, and that is a separate document with its own rows. The automotive part is AEC-Q100 grade 1, specified from minus 40 to plus 125 degrees, with HBM level 2 and CDM level C6, and the addendum prints the MSL as level 1 unlimited for the Q1 rows where the plain part carries a different level. The electrical table is the same in both documents, so a channel qualified on the plain part does not need a new characterisation for the automotive one, only a new part number and a new set of paperwork.
Three thousand pieces is a line quantity and the reel is the carrier that fits a feeder. Our BOM scrubbing page covers the gain option check against the bill of materials, and the lead time page covers the long quote case.
How do I choose between the four gains? From the shunt and the converter range: pick the option that puts the working current nearest the top of the converter's span without clipping.
Is the 26 volt common mode rating a working limit? Yes, it is the recommended operating range, and the negative end reaches 0.2 volts below ground for a low side shunt.