Contact Us

INA155UA

Brand: Texas Instruments
Texas Instruments INA155UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA155UA — Power Management & Signal Chain | Superb Automation

INA155UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA155UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA155UA: the same amplifier with 80 dB of rejection, in rails

INA155UA is the wider grade of the same CMOS instrumentation amplifier, and on this family the wider grade is a rejection bin rather than an offset bin. Offset stays at 200 microvolts typical and 1 millivolt maximum; common mode rejection falls from 92 dB minimum to 80 at a gain of 10 and from 86 to 77 at 50. Everything else, the gain strap, the picoamp bias, the rail to rail output and the 2.7 volt floor, is identical.

Twelve decibels is a factor of four in error, and on a bridge front end that is the difference between a channel that meets a 1 per cent specification without a trim and one that does not. The arithmetic is worth doing on the actual common mode swing rather than on the supply: a 2 volt swing divided by 10 to the 3.7 is 400 microvolts, which on a 20 millivolt full scale bridge is 2 per cent of reading, and no amount of gain removes it.

INA155UA as the vendor document publishes it

Gain10 V/V with pin 1 open, 50 V/V with pin 1 linked
Gain law with an external resistor10 plus 400 kohm divided by 10 kohm plus RG
Gain error, G = 100.02 per cent typical, 0.1 maximum
Gain error, G = 500.05 per cent typical, 0.25 maximum
Gain drift, G = 102 ppm per degree typical, 10 maximum
Offset200 microvolts typical, 1 millivolt maximum
Offset over temperature1.5 millivolts maximum
Offset drift5 microvolts per degree
Common mode rejection, G = 1080 dB minimum, 100 typical on the UA grade
Common mode rejection, G = 5077 dB minimum, 90 typical on the UA grade
Input bias current1 picoamp typical, 10 picoamps maximum
Input impedance10 to the 13 ohms in parallel with 3 picofarads
Voltage noise at 1 kHz40 nanovolts per root hertz
Bandwidth, G = 10550 kHz
Bandwidth, G = 50110 kHz
Slew rate6.5 volts per microsecond
Settling to 0.01 per cent8 microseconds at G = 10, 15 at G = 50
Output swing from rail5 millivolts typical, 10 maximum into 10 kohm
Quiescent current1.7 milliamps typical, 2.1 maximum, 2.6 over temperature
Supply range2.7 to 5.5 volts specified, 2.5 to 6 volts operating
Bodyeight pin SOIC in the UA grade
Temperature rangeminus 40 to plus 85 degrees specified
Catalogue codeINA155UA
Vendor stringINA155UA
Carrierrails
GradeUA, 80 dB minimum rejection at a gain of 10

Two hundred microvolts of offset and one picoamp of bias

Offset on INA155UA is 200 microvolts typical and 1 millivolt maximum referred to the input, 1.5 millivolts over the full temperature range, with a drift of 5 microvolts per degree. Bias current is 1 picoamp typical and 10 picoamps maximum on each input, offset current the same, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. On a bridge or a thermocouple that combination is close to ideal, because the source impedance never generates an error the amplifier cannot ignore.

The picoamp figure only holds inside the common mode window and inside the diode clamp. The inputs are clamped to the rails, and the vendor states that a signal swinging more than 0.5 volts beyond either rail has to be current limited to 10 milliamps or less, which means a series resistor on any input that can see a cable fault. Ten picoamps into 1 gigohm is 10 millivolts, ten times the maximum offset, so a high impedance source needs a guard ring and a clean board rather than a better grade of the same part.

Rail to rail output, five millivolts from the rail on 2.7 volts

The output of INA155UA reaches to within 5 millivolts of either rail typical and 10 millivolts maximum into a 10 kohm load, which is what makes a single 3.3 volt rail usable for a sensor that spans most of the supply. The input is a different story: the common mode window runs from 0.3 to 5.2 volts on a 5.5 volt supply and from 0.2 to 2.5 volts on 2.7 volts, so the input does not reach either rail and the last 0.3 volts at the top are outside the window.

That asymmetry sets the reference. On a single supply the Ref pin sits at mid rail, the output swings both ways around it, and the usable span is 5 millivolts to supply minus 5 millivolts. A 12 bit converter behind it then sees the full code range, which is the reason the part is sold as an analogue front end rather than as a general purpose amplifier: the two errors that usually eat the top and bottom of a converter's range are the ones the rail to rail output removes.

A gain of 10 or 50 from a strap on pin 1

INA155UA is a three amplifier CMOS instrumentation amplifier with the feedback resistors trimmed on the die to a gain of 10 V/V, and pin 1 decides whether an extra pair is brought in to make that 50. Gains between the two are set with one resistor in series with the RG pins, and the vendor gives the law as 10 plus 400 kohm divided by 10 kohm plus RG, so 400 kohm of external resistance lands near 20 and 100 kohm lands on 50 exactly.

The strap is the part that gets taken for granted. The 0.02 per cent gain error printed in the table belongs to the internal network alone, so a 1 per cent resistor in the strap turns the channel into a 1 per cent channel, and a mechanical jumper with a tired contact adds a resistance the vendor never characterised. Use a solder link or a zero ohm part, and keep the trace from the strap pin short, because that node sits at the summing point of the first stage.

Where a fixed gain CMOS front end is the right buy

INA155UA earns its place in four kinds of channel: a bridge, RTD or thermocouple front end where the source impedance is high and the bias current has to be picoamps; a battery instrument where the rail to rail output lets a 3.3 volt converter use its whole range; a medical amplifier where the input is a pair of electrodes and the offset has to be small enough not to saturate the second stage; and a multiplexed logger where 5 microseconds of settling buys channels.

It stops at four things. The gain is 10 or 50 and the resistor between them costs the trimmed accuracy. Common mode rejection falls from 100 dB at a gain of 10 to 90 at 50, so a channel that needs rejection at high gain is looking at the three op amp parts with a higher supply. The supply ceiling of 5.5 volts rules out a plus or minus 15 volt front end entirely. And the 5.5 MHz gain bandwidth caps a full scale signal at a few hundred kilohertz whatever the small signal curve suggests.

550 kHz at a gain of 10, 110 at 50

INA155UA carries 550 kHz of small signal bandwidth at a gain of 10 and 110 kHz at 50, which is the same 5.5 MHz gain bandwidth product written twice. Slew rate is 6.5 volts per microsecond, settling to 0.1 per cent is 5 microseconds at a gain of 10 and 11 at 50, and to 0.01 per cent it is 8 and 15. Overload recovery from a 50 per cent overdrive is 0.2 microseconds, which is fast because the amplifier never leaves its linear region far enough to saturate an internal node.

Those numbers fit a multiplexed front end comfortably. Sixteen channels at 11 microseconds of settling is 176 microseconds per scan, so a 10 kilo-sample logger can scan sixteen channels five times over in its period, and the amplifier is not the limit. What limits the scan is the input filter and the multiplexer charge injection, both of which have to settle through the same 5 microsecond window, and the vendor's own application note on driving converters puts the series resistor and the capacitor around that arithmetic.

1.7 milliamps, a 2.7 volt floor and two bodies

INA155UA draws 1.7 milliamps typical and 2.1 maximum, rising to 2.6 over temperature, from a supply specified between 2.7 and 5.5 volts and operating between 2.5 and 6. At 5.5 volts and 2.1 milliamps the dissipation is 11.6 milliwatts, which in the eight pin body at 150 degrees per watt raises the junction 1.7 degrees, so the package is never the limit at any point in the window. Short circuit current is 50 milliamps into ground and the output is stable into the capacitive load shown in the vendor curve.

Two bodies carry the part. The SO-8 holds the U and UA grades on rails or on a 2500 piece reel, and the MSOP-8 holds the E and EA grades on a 250 or a 2500 piece reel with the marking A55. Both are specified from minus 40 to plus 85 degrees for the electrical table and from minus 55 to plus 125 for operation, which is a wide operating window with a narrow guarantee and is the row to check when a channel has to survive a cold start rather than to measure accurately at minus 40.

Before the UA grade is written into a bill of materials, check the rejection the channel actually needs. Our drop in replacement check page sets out the rows to compare between the two grades, and the vendor consolidation page covers buying both grades from one line rather than two.

Is the UA grade cheaper because it is a slower part? No. The bandwidth, the slew rate and the settling time are the same rows on both grades; only the rejection limits and the price differ.

Can a UA part stand in for a U part? Only against the rejection row, and an inspector comparing labels will see the difference. Put the substitution on a deviation rather than on a verbal instruction.