INA149AIDR
Product Specifications
INA149AIDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA149AIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA149AIDR: the same 275 volt part on a reel
INA149AIDR is INA149AID on a reel: the R suffix is the carrier, not a grade. The electrical rows are unchanged, plus or minus 275 volts of common mode, 1100 microvolts of offset maximum, 0.02 per cent of gain error, 500 kHz, and 900 microamps from a supply between plus or minus 2 and plus or minus 18 volts.
This is the carrier a multi channel build wants, and multi channel is the natural shape of the application: a three phase drive has three of these, a battery rack has one per module, and a test rack has one per channel. The repeating front end is the reason the part exists in a reel at all, and it is also the reason the reference and the supply decoupling have to be right once rather than per channel.
INA149AIDR as the vendor document publishes it
| Gain | 1 V/V fixed |
| Gain error | 0.005 per cent typical, 0.02 maximum |
| Gain drift | 1.5 ppm per degree typical, 10 maximum |
| Nonlinearity | 0.0005 per cent typical, 0.001 maximum of full scale range |
| Offset | 350 microvolts typical, 1100 maximum |
| Offset drift | 3 microvolts per degree typical, 15 maximum |
| Supply rejection | 90 dB minimum, 120 typical |
| Common mode range | plus or minus 275 volts |
| Overload withstand | 500 volts momentary, common mode or differential |
| Common mode rejection at dc | 90 dB minimum, 100 typical |
| Common mode rejection at 1 kHz | 90 dB minimum with 500 volts peak to peak |
| Input impedance | 800 kohm differential, 200 kohm common mode |
| Voltage noise | 20 microvolts peak to peak, 550 nanovolts per root hertz at 10 kHz |
| Bandwidth | 500 kHz small signal, 32 kHz full power at 20 volts peak to peak |
| Slew rate | 1.7 volts per microsecond minimum, 5 typical |
| Settling to 0.01 per cent | 7 microseconds on a 10 V step |
| Output swing | plus or minus 13.5 volts on plus or minus 15 volt supplies |
| Quiescent current | 810 microamps typical, 900 maximum, 1.1 milliamps over temperature |
| Supply range | plus or minus 2 to plus or minus 18 volts |
| Stable load capacitance | 10 nanofarads |
| Body | eight pin SOIC, pin compatible with the INA117 and INA148 |
| Temperature range | minus 40 to plus 125 degrees |
| Catalogue code | INA149AIDR |
| Carrier | reel, R suffix |
| Grade | A grade in the D body |
90 dB minimum rejection from minus 40 to plus 125 degrees
Common mode rejection on INA149AIDR is 90 dB minimum and 100 typical at dc with the common mode at plus or minus 275 volts, and 90 dB minimum at 500 Hz and at 1 kHz with a 500 volt peak to peak common mode. The temperature row is the unusual one: the minimum holds from minus 40 to plus 125 degrees, not just at 25, so the rejection does not have to be derated across the operating range.
Ninety dB is a factor of thirty thousand, so 275 volts of common mode becomes 8.7 millivolts referred to the input, and 500 volts of transient becomes 16 millivolts. That is the number that decides whether the part can be used ahead of a 12 bit converter on a plus or minus 10 volt range: 8.7 millivolts is 0.09 per cent of full scale, below the converter's own linearity, and at 16 bits it is not and the common mode has to be reduced or the measurement taken differentially.
500 kHz, 5 volts per microsecond, 7 microseconds to settle
The small signal bandwidth of INA149AIDR is 500 kHz, the slew rate is 1.7 volts per microsecond minimum and 5 typical, the full power bandwidth is 32 kHz at 20 volts peak to peak, and the settling time to 0.01 per cent on a 10 V step is 7 microseconds. Output noise is 20 microvolts peak to peak from 0.01 to 10 Hz and 550 nanovolts per root hertz at 10 kHz.
The ratio between 500 kHz of small signal bandwidth and 32 kHz of full power bandwidth is the practical limit: a 20 volt swing at 1.7 volts per microsecond cannot complete faster than about 12 microseconds, so anything above 32 kHz comes out as a triangle. For a line frequency measurement that is irrelevant; for a switching waveform it is the reason to use a different part. The 7 microsecond settling figure is the one a multiplexed channel budgets, and it is fast enough for 16 channels at 9 kilohertz per channel.
Plus or minus 275 volts of common mode and 500 volts of overload
INA149AIDR is a unity gain difference amplifier whose input common mode range is plus or minus 275 volts, and whose inputs survive a momentary common mode or differential overload of 500 volts. That combination is what allows the part to sit directly on a three phase line or a battery stack without a divider, and it is why the vendor positions it as a replacement for an isolation amplifier where galvanic isolation is not required.
The economic argument is in the paragraph that follows the first one in the vendor document: an isolation amplifier needs an isolated supply on the input side, and that supply brings ripple, noise, quiescent current and a transformer. Removing it removes the isolated dc to dc converter, its creepage distance and its cost, and leaves a part that measures small differentials on a large common mode with 90 dB of rejection. What is given up is the isolation itself, which matters for safety and not for measurement.
900 microamps from plus or minus 2 to plus or minus 18 volts
INA149AIDR draws 810 microamps typical and 900 maximum at plus or minus 18 volts, rising to 1.1 milliamps over temperature, from a supply between plus or minus 2 and plus or minus 18 volts. The output swings to plus or minus 13.5 volts on a plus or minus 15 volt supply, limits short circuit current at 25 milliamps and drives 10 nanofarads without sustained oscillation.
The 2 volt floor is unusual for a part with a 275 volt input window and it matters on a 3.3 V rail, where the part still works with the window scaled to twice the supply. The output window of plus or minus 13.5 volts on plus or minus 15 volts is also wider than most instrumentation amplifiers manage, which is what allows the part to drive a plus or minus 10 volt converter directly without a second stage and without giving up the headroom that the converter needs.
1100 microvolts of offset and 0.02 per cent of gain error
Offset on INA149AIDR is 350 microvolts typical and 1100 maximum, with 3 microvolts per degree typical and 15 maximum of drift over minus 40 to plus 125 degrees. Gain error is 0.005 per cent typical and 0.02 maximum, gain drift 1.5 ppm per degree typical and 10 maximum, and nonlinearity 0.0005 per cent typical and 0.001 maximum of full scale range. Supply rejection is 90 dB minimum.
On a 275 volt common mode the offset is the small term and the rejection is the large one, which is the opposite of a low voltage instrumentation amplifier where the offset usually dominates. Eleven hundred microvolts on a plus or minus 10 volt range is 0.0055 per cent of full scale, a twentieth of what a 16 bit converter can resolve, so the offset does not need trimming and the drift over 125 degrees, 15 microvolts per degree or 2.5 millivolts, still does not. What does need attention is the 0.02 per cent gain error, which is 4 millivolts on a 20 V span and is a ratio error that no single point trim removes.
Pin compatible with the INA117 and the INA148
The vendor states that INA149AIDR is pin compatible with the INA117 and the INA148 family, in the eight pin SOIC, and that it improves on both. On a board that already carries one of those parts, INA149AIDR is therefore a candidate for a straight swap, and the figures that make it attractive are the 500 kHz bandwidth against 100 to 155 kHz on the INA148, the 90 dB minimum rejection held over temperature, and the 0.02 per cent gain error.
Three rows have to be checked before a swap is signed off. The supply window differs: plus or minus 2 to plus or minus 18 volts here against plus or minus 1.35 to plus or minus 18 on the INA148. The reference arrangement differs on the two reference pins, and a board that ties one of them to a divider will not behave the same way. And the output swing, plus or minus 13.5 volts here, is wider than the part it replaces, so a circuit that relied on clipping at a lower level will now deliver a larger signal to whatever follows.
A reel is a stock position for a rack build. The part is not a commodity, so the reel is bought for continuity rather than for price, and the second source question is answered by the pin compatible family rather than by a cheaper equivalent. Our lead time page covers the long quote case, and the pin to pin page covers the pin compatible candidates.
Does the R suffix change the temperature range? No. The family is specified from minus 40 to plus 125 degrees and the carrier does not touch it.
Why does the output stop at plus or minus 13.5 volts on a plus or minus 15 V supply? Because the internal stage needs 1.5 volts of headroom on each side, and that is the row a plus or minus 10 V converter behind it has to be checked against.