INA141U-2
Product Specifications
INA141U-2
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA141U-2 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA141U-2: a reel string that does not decode to a published row, and how to confirm it
The INA141U-2 is a catalogue string that does not decode cleanly against the vendor addendum. The addendum prints INA141U in a 75 piece tube and INA141U/2K5 at 2500 pieces on a large reel, and a bare minus 2 is not one of those rows. It may be a truncated rendering of the slash 2K5 suffix, or a quantity suffix from another system, and the honest position is that the quantity has to be confirmed before the line is quoted.
What is certain is the device. The INA141U is the tight bin of a two gain instrumentation amplifier, 10 V/V with pins 1 and 8 open and 100 with them shorted, on 750 µA of supply current, with 200 kHz at a gain of 100 and a 117 dB minimum rejection at that gain. The offset is 100 µV maximum at a gain of 10 and 50 at a gain of 100 on the U bin.
The INA141U-2 rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback input |
| Vendor status | Device active, the catalogue string is not a published row |
| Data sheet | SBOS052B, revised January 2026 |
| Published rows for this body | INA141U in a 75 piece tube, INA141U/2K5 at 2500 pieces |
| Gain | 10 V/V open, 100 V/V shorted |
| Gain error | 0.05 per cent maximum at a gain of 10 |
| Input offset voltage | 100 µV maximum at a gain of 10, 50 at a gain of 100 |
| Offset drift | 2 µV per degree at a gain of 10 |
| Input bias current | 5 nA maximum |
| Common mode rejection | 117 dB minimum at a gain of 100 |
| Bandwidth | 200 kHz at a gain of 100, 994 kHz at a gain of 10 on SHE |
| Settling | 7 µs at a gain of 10, 9 µs at a gain of 100 |
| Output swing | 1.4 V from each rail on SHE, 0.15 V on TID |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 750 µA typical |
| Body | SOIC, D outline, 8 pins |
| Moisture level | Level 3, 260 degrees, 168 hour floor life on the tube and the reel rows |
| Temperature range | Minus 40 to plus 85 degrees |
A gain of 10 or 100 from a jumper, not a resistor
INA141U-2 sets its gain from the connection between pins 1 and 8 rather than from an external resistor: open, the gain is 10 V/V, shorted, it is 100 V/V. There is no gain resistor to buy, place, tolerance or drift, and the gain error is 0.05 per cent maximum at a gain of 10 and 0.075 per cent at a gain of 100 on the U bin, with a 10 ppm per degree drift. On a channel that has to be 10 or 100 and nothing else, that is the tidiest arrangement in the catalogue.
The jumper is not free of resistance. The vendor states that 0.5 ohm in the connection reduces the gain by 0.1 per cent, so a 2 ohm trace and a 1 ohm via are 0.4 to 0.6 per cent, which is ten times the trimmed gain error. The short should be a wide trace directly between the two pins, or a 0 ohm link placed on the pin centres, and the connection should be checked on the first article rather than assumed.
750 microamps and 200 kHz at a gain of 100
Quiescent current on INA141U-2 is 750 microamps typical and 800 maximum, on a supply from plus or minus 2.25 V to plus or minus 18 V. That is four times below the INA131 and within a tenth of the INA129, and it comes with a current feedback input stage that holds 200 kHz of bandwidth at a gain of 100, where the INA129 falls from 1.3 MHz at unity gain to 200 kHz at a gain of 100 and keeps falling as the gain rises.
Settling to 0.01 per cent is 7 microseconds at a gain of 10 and 9 microseconds at a gain of 100, with a 4 microsecond recovery from a 50 per cent overload. For a multiplexed front end that is a scan rate of about 100 kilohertz per channel, which is limited by the converter rather than the amplifier. The supply current is quoted with the input at zero volts, so a channel driving a heavy load draws more through the output stage.
SHE and TID: one part number, two different chips
The same order code can come from either of two fabrication flows, and on INA141U-2 the flows differ in almost every row that matters. Offset at a gain of 10 is 100 microvolts maximum on SHE and 80 on TID for the U bin, bandwidth is 994 kHz against 610, output swing is 1.4 V from each rail against 0.15 V, voltage noise at 1 kHz is 12 against 15.1 nanovolts per root hertz, and quiescent current is 750 against 590 microamps. None of that appears in a distributor listing.
The output swing difference is the one that breaks boards. A part specified to swing within 1.4 V of the rails on a plus or minus 5 V supply stops at plus or minus 3.6 V, which is not enough for a 4 V full scale signal, while the other flow reaches plus or minus 4.85 V. A channel checked against the headline number and built with the other flow fails at the top of its range, and the failure looks like a gain error rather than a headroom limit.
40 V of protection and 117 dB of rejection at a gain of 100
The inputs of INA141U-2 survive 40 V beyond either rail, and the protection is internal, so an input wired to a live 24 V loop with the amplifier unpowered does not destroy it. Common mode rejection is 117 dB minimum at a gain of 100 on the U bin, 110 on the UA bin, and 100 and 93 dB at a gain of 10, measured with a 1 kohm source imbalance at plus or minus 13 V. Rejection rises with gain because the input stage, not the output stage, does the work.
The common mode range is 2 V inside each rail with the output at zero, so on a plus or minus 15 V supply the window is plus or minus 13 V at that output level and narrows as the output swings. On a single 5 V supply the window is small and a mid rail reference is mandatory. Input impedance is 100 Gohm differential in parallel with 2 pF, so a high impedance sensor is not loaded by the amplifier.
100 microvolts on the U and 250 on the UA at a gain of 10
The offset bin is the first thing to read on INA141U-2: at a gain of 10 the U bin is 100 microvolts maximum and the UA bin 250, and at a gain of 100 they tighten to 50 and 125 because the offset is referred to the input and the gain multiplies it. Drift follows the same split, 2 microvolts per degree against 2.5 at a gain of 10 and 0.5 against 1.5 at a gain of 100. The chip flow moves these numbers again by up to 20 per cent.
On a 10 mV full scale bridge at a gain of 100 the output full scale is 1 V and the 50 microvolt input offset is 5 mV at the output, half a per cent, which is trimmed once. The drift of 0.5 microvolts per degree is 50 microvolts at the output over 100 degrees, a tenth of a per cent, which is not trimmed and is usually acceptable. On the UA bin both numbers double, which is the difference between a calibrated instrument and a monitored one.
The D body, a tube of 75 and a reel of 2500
INA141U-2 is an eight pin SOIC at 4.9 by 6 mm, sold in a 75 piece tube at moisture level 3 and on a 2500 piece large reel under the slash 2K5 suffix, both active in the current addendum. The load capacitance limit is 1000 pF and short circuit current is 20 mA continuous to mid supply, so the output drives a cable with a series resistor and does not drive a speaker. Gain of 10 or 100 is set by the jumper, so one part covers two ranges and the reel covers both.
Because the gain is set by a pin connection rather than a resistor, the same reel can build a gain of 10 board and a gain of 100 board, which simplifies stock. The cost is that the gain is not adjustable and the two values are six times apart, so a channel that needs 30 has to change part. The 0.5 ohm rule also means the jumper is a real component on the bill of materials and should be treated as one rather than as a copper bridge drawn at the last minute.
Buying INA141U-2
The order should carry the piece count and the carrier as words, because the string itself does not pin either down. If the intent was 2500 on a reel, the addendum row is INA141U/2K5 and that is what the confirmation should come back against; if the intent was a tube of 75, the row is INA141U and the string is a typo rather than a quantity.
On a part where the chip origin moves the output swing from 1.4 V to 0.15 V from the rails, the lot record matters as much as the order line. Our pin to pin cross reference page covers the packages, and the obsolete part cross reference page is where an old string like this usually gets resolved against a current one.
Questions that arrive with this part number
What the minus 2 means is the first question, and there is no published row that ends that way, so the answer is a confirmation rather than an assumption. Whether the part is still active is the second, and it is: both the tube and the 2500 piece reel are in production, and only the catalogue string is unclear.
The third is the gain connection, which is a jumper between pins 1 and 8 and not a resistor, and 0.5 ohm in that jumper costs 0.1 per cent of gain. The fourth is the output swing difference between chip origins, which is the specification that decides whether a 4 V signal fits on a plus or minus 5 V supply, and it is not visible anywhere in the order code.