INA137UA-2K5
Product Specifications
INA137UA-2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA137UA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA137UA-2K5: the same minus 6 dB receiver on a 2500 piece reel, noise floor and all
The INA137UA-2K5 is the reel row for the minus 6 dB line receiver, which the addendum prints as INA137UA/2K5 at 2500 pieces on a 12.4 mm tape. The part is the same eight pin SOIC with the same 12 kΩ and 6 kΩ network, the same 0.5 V/V gain, the same minus 106 dBu noise floor and the same 2.9 mA of supply current per channel.
The reel is the production carrier and the tube is the pilot carrier, and both are active, which is worth knowing because several parts in this catalogue have lost the tube row. On a stereo build the dual INA2137UA/2K5 puts two channels on one 16.4 mm tape with 123 dB of separation, and the single is the right buy only when the second channel is not needed.
The INA137UA-2K5 rows as the addendum publishes them
| Part class | Audio differential line receiver, fixed minus 6 dB |
| Vendor status | Active, production |
| Data sheet | PDS-1391B, Burr-Brown, July 1997 |
| Addendum row it normalises to | INA137UA/2K5, 2500 pieces |
| Gain | 0.5 V/V, minus 6 dB |
| Gain error | 0.1 per cent maximum |
| Total harmonic distortion plus noise | 0.0005 per cent at 1 kHz |
| Noise floor | Minus 106 dBu referred to the output |
| Output noise | 3.5 µV rms over 20 Hz to 20 kHz |
| Input offset voltage | 1 mV maximum referred to the output |
| Common mode rejection | 90 dB typical |
| Input impedance | 24 kΩ differential, 18 kΩ common mode |
| Bandwidth | 4 MHz small signal |
| Slew rate | 14 V per microsecond |
| Settling | 3 µs to 0.01 per cent |
| Supply range | Plus or minus 4 V to plus or minus 18 V |
| Quiescent current | 2.9 mA maximum per amplifier |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces, 330 mm reel |
| Moisture level | Level 3, 168 hour floor life |
| Dual sibling | INA2137UA/2K5, 14 pin SOIC, 2500 pieces |
Minus 6 dB, and the two ways the network is wired
INA137UA-2K5 is a differential line receiver with a fixed 6 dB of attenuation, 0.5 V/V, set by the on-chip 12 kohm and 6 kohm resistors. The same network can be wired for a gain of 2, which the vendor shows as a receiver with the input and feedback resistors reversed; the resistors do not change, only which pins the signal and the reference reach. That is why one part covers both a pad down and a pad up function, and why the pin connection has to be read before the gain is assumed.
For unity gain the vendor points to the INA134 instead, so the three parts in this group cover 0.5, 1 and 2 V/V with the same topology. Gain error on INA137UA-2K5 is 0.1 per cent maximum and gain drift is 1 ppm per degree, so the 6 dB is accurate to a hundredth of a decibel before the source impedance is considered. The network is ratio matched but its absolute value carries 25 per cent tolerance on the older sheets.
24 kohm differential and 18 kohm common mode across the source
The input network of INA137UA-2K5 presents 24 kohm differential and 18 kohm common mode, lower than the unity gain part because the 12 kohm and 6 kohm resistors sit in a different ratio. Across a 50 ohm line that is a 0.2 per cent loading error, which the 0.1 per cent gain error row already covers; across a 10 kohm source it is a 30 per cent divider and the channel has to be recalibrated.
Lower impedance also means the network dominates the noise at ordinary source impedances, which is why the noise row is specified with the network included. On a 600 ohm line the thermal noise of 24 kohm is about 20 nanovolts per root hertz, four times the 26 nanovolts per root hertz the sheet quotes at 1 kHz when the source is zero. The line impedance, not the amplifier, sets the noise floor of an installed system.
A noise floor of minus 106 dBu on a line receiver
The audio rows on INA137UA-2K5 are a step better than the unity gain sibling: total harmonic distortion plus noise is 0.0005 per cent at 1 kHz with a 10 V rms input, the noise floor is minus 106 dBu referred to the output over 20 kHz, and the headroom is plus 23 dBu. The output noise over the audio band is 3.5 microvolts rms against 7 on the INA134, because the 6 dB of attenuation is applied before the amplifier sees the signal.
That is the trade the part makes: 6 dB of level is given away at the input and 6 dB of noise performance is gained at the output, so a plus 23 dBu line arrives at the converter at plus 17 dBu with the same signal to noise ratio as the unity gain part and twice the headroom margin. On a broadcast chain where the nominal level is plus 4 dBu and the peaks are plus 20, the attenuation is what keeps the amplifier out of clipping.
Plus or minus 46.5 V of common mode and 90 dB of rejection
Common mode rejection on INA137UA-2K5 is 90 dB typical and 74 dB minimum at a plus or minus 46.5 V common mode with the source at zero ohms, and the input common mode range extends to three times the supply minus seven and a half volts in each direction. On plus or minus 18 V that is plus or minus 46.5 V, so a chassis difference of tens of volts is inside the window rather than outside it. The absolute maximum input is 80 V.
Rejection is the entire function of the part, and it is a ratio match measurement: the two input paths have to see the same impedance. A 1 kohm imbalance in a 24 kohm network is a 4 per cent mismatch and the 90 dB becomes 28 dB, which is audible hum at mains frequency. The specification assumes the source is balanced, and a line receiver is only as good as the cable and the connectors in front of it.
1 mV referred to the output, and the two gain configurations of one network
Input offset on INA137UA-2K5 is 1 mV maximum referred to the output with a 2 microvolt per degree drift, and the offset is referred to the output because the gain is 0.5. At the output the 1 mV is 1 mV; at the input it is 2 mV, which is what an installer measuring at the connector would see. Long term stability is not quoted on this sheet, and the power supply rejection is 60 microvolts per volt maximum over the plus or minus 4 to plus or minus 18 V window.
The ordering rows are simple: INA137UA-2K5 is a 75 piece tube at moisture level 3, and the 2500 piece reel is the same part under the slash 2K5 suffix. The dual INA2137UA is the fourteen pin SOIC at 50 pieces per tube or 2500 on a reel, with 123 dB of channel separation at 1 kHz, which is why a stereo pair goes into one package rather than two singles.
2.9 mA, plus or minus 4 to 18 V, and 150 degrees per watt
Each channel of INA137UA-2K5 draws 2.4 mA typical and 2.9 mA maximum over a supply window of plus or minus 4 V to plus or minus 18 V, with an absolute maximum of 40 V total. The eight pin SO-8 has a junction to ambient figure of 150 degrees per watt against 100 for the DIP, so about 100 milliwatts per channel raises the junction 15 degrees in the surface mount body. The specified range is minus 40 to plus 85 and the operating range minus 55 to plus 125.
The output swings to within 1.8 V of the positive rail and 1.6 V of the negative rail, which on plus or minus 18 V is plus or minus 16 V or plus 26 dBu, and the continuous output current is 60 mA into a 600 ohm load. Load capacitance is limited to 500 pF, so a cable needs a series resistor of 47 to 100 ohms at the output, and the part is stable into that arrangement.
Buying INA137UA-2K5
A reel of 2500 covers a long production run for an audio product, and the level 3 floor life is the only schedule constraint on the part. On a build that consumes a reel a year, the alternative is cut tape from a distributor, which arrives with an unknown exposure history and has to be baked before a reflow.
The dual is the volume answer for a stereo channel: two receivers on one tape, 123 dB of separation and a single placement. The single is the right buy for a mono product or where the two channels sit far apart on the board. Our vendor consolidation page covers the question of how many line items a small audio build should carry.
Questions that arrive with this part number
Whether the reel spelling is a different part is the first question, and it is not. Whether the part can drive a 600 ohm load to plus 26 dBu is the second, and the 60 mA output current says it can, with the 500 pF capacitance limit as the constraint on the cable rather than on the load.
The third is the gain of 2 configuration. The same network supports it, and the vendor figure shows the reversed connection, but the board has to be laid out for it, so a product that needs both 0.5 and 2 has two builds rather than one with a jumper. The fourth is the offset, 1 mV referred to the output, which at the input is 2 mV and is the number an installer would measure at the connector.