INA132UA2K5
Product Specifications
INA132UA2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA132UA2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA132UA2K5: the wider offset bin of the unity gain part, on the reel that is the only active carrier
The INA132UA2K5 is the A grade of the unity gain difference amplifier on a 2500 piece reel, with a 500 µV maximum offset referred to the output against 250 on the plain grade, and the same 0.1 per cent gain error against 0.075. Both grades share the 175 µA supply current, the 300 kHz small signal bandwidth, the 80 kΩ network and the single supply window from 2.7 V to 36 V.
The grade difference is small in absolute terms and it decides a category of application: on a 100 mV shunt signal, 500 µV is half a per cent and 250 is a quarter, and neither is trimmed on a low cost board. Where the channel is calibrated the two are interchangeable; where it is not, the plain grade is the only one that meets a half per cent budget on a small signal.
The INA132UA2K5 rows as the addendum publishes them
| Part class | Unity gain difference amplifier, trimmed resistor network |
| Vendor status | Active, production, the only active grade in a tube or a reel |
| Data sheet | SBOS059B, revised January 2026 |
| Addendum row | INA132UA/2K5, 2500 pieces on a large reel |
| Grade | A suffix, 500 µV maximum offset and 0.1 per cent gain error |
| Gain | 1 V/V fixed |
| Gain error | 0.1 per cent maximum |
| Gain nonlinearity | 0.002 per cent of full scale |
| Input offset voltage | 500 µV maximum referred to the output |
| Offset drift | 10 µV per degree maximum |
| Common mode rejection | 90 dB typical, 70 dB minimum |
| Input impedance | 80 kΩ differential |
| Bandwidth | 300 kHz small signal |
| Settling | 88 µs to 0.01 per cent |
| Supply range | 2.7 V to 36 V single, plus or minus 1.35 V to plus or minus 18 V dual |
| Quiescent current | 175 µA typical |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces on a large reel |
| Moisture level | Level 3, 260 degrees, 168 hour floor life |
| Temperature range | Minus 40 to plus 85 degrees |
250 microvolts on the U and 500 on the UA
The offset of INA132UA2K5 is referred to the output and quoted at 250 microvolts maximum on the U bin and 500 microvolts on the UA bin at a plus or minus 15 V supply, with a drift of 5 and 10 microvolts per degree. At unity gain the input referred and output referred figures are the same number, which makes this part easy to budget: the offset is the offset.
The second point about the bins is availability. In the current addendum the tube rows for both INA132U and INA132UA are marked obsolete with no quantity and no carrier, and only the 2500 piece reel rows are active. That is a real constraint on a prototype build: the part is not discontinued, but it is sold in reels, so a ten board build either buys a reel or buys from stock that was cut from one. The reel row carries moisture level 3 with a 168 hour floor life.
One trimmed network instead of four resistors
A difference amplifier is one op amp and four resistors, and the four resistors have to be ratio matched to better than the amplifier's own gain error or the common mode rejection collapses. INA132UA2K5 puts the network on the die, laser trimmed, with the ratios tracking over temperature because they sit on the same piece of silicon. The published result is 0.075 per cent maximum gain error and 0.001 per cent of full scale nonlinearity on the U bin, with a gain drift of 10 ppm per degree.
The alternative on a discrete build is four 0.1 per cent resistors with a 25 ppm coefficient, which costs more board area and more test time than the integrated network costs in unit price, and still does not track as well because four separate parts do not sit at the same temperature. That is the argument for buying the function rather than building it, and it is the reason this part exists in the catalogue at 175 microamps of supply current.
175 microamps and the 80 kohm network across the source
The supply current is 175 microamps typical, which is what lets INA132UA2K5 sit in a battery instrument or a loop powered transmitter. The cost of that current is the resistor network: the differential and common mode input impedance are both 80 kohm, and 80 kohm across a source is a load. A 1 kohm source sees a 1.2 per cent gain loss from the divider, which at 0.075 per cent gain error is twenty times the amplifier contribution and has to be calibrated or buffered.
On a bridge or a shunt the loading also unbalances the source, and an unbalanced source converts common mode into differential. That is why the four source resistances around a difference amplifier should match, and why a series resistor added to one input for protection has to be added to the other. The network is ratio matched but its absolute value carries 25 per cent tolerance on the older family sheets, so the divider error is predictable but not small.
A 2.7 V to 36 V window and a common mode that reaches the negative rail
INA132UA2K5 runs from a single supply between 2.7 V and 36 V, or from a dual supply between plus or minus 1.35 V and plus or minus 18 V, and the internal amplifier common mode range extends to the negative supply. That last row is what makes the part usable on a single rail: a shunt in the return leg sits at a few tens of millivolts above ground, which is inside the window on a single supply and outside it on many difference amplifiers.
The common mode range at the top is 2 times the positive rail minus 2 V, so on a 5 V single supply the window runs from ground to about 8 V, and on plus or minus 15 V it runs from minus 15 V to plus 28 V. Input voltage beyond that does not damage the part, because the absolute maximum input is 80 V, but the output stops following. On a current sense application the window is therefore never the limit; on a high side measurement it can be.
300 kHz, 10 nF of load and a slew rate of 0.1 to 0.25 V per microsecond
The small signal bandwidth of INA132UA2K5 is 300 kHz at unity gain, but the large signal behaviour is set by a slew rate of 0.1 volts per microsecond on one chip origin and 0.25 on the other, with a settling time of 88 microseconds to 0.01 per cent after a 10 V step. A 300 kHz small signal figure next to a 0.1 V per microsecond slew is the classic trap: the bandwidth describes a millivolt signal, and a 10 V step takes 100 microseconds. The output is stable into 10 nanofarads, which is unusual and useful for a cable or a multiplexer input.
Output swing is to within 0.8 V of the positive rail into 100 kohm and 0.25 V of the negative rail into 10 kohm.
Short circuit current is quoted by chip origin: 6 mA source and 15 mA sink on one flow, 26 and 22 mA on the other, so a circuit that relies on a specific fault current has to know which chip it received. The quiescent current is the same 175 microamps on both. On a single 3.3 V supply the output swing leaves about 2.5 V of usable range, which is the number to check before putting a 3 V full scale signal through it.
90 dB of rejection and the source imbalance that removes it
Common mode rejection on INA132UA2K5 is 90 dB typical and 76 dB minimum on the U bin, measured with the common mode swept from minus 15 to plus 28 V. The rejection depends entirely on the ratio match between the two input paths, so a 1 kohm imbalance in the source, which is one precision resistor in series with one input, converts common mode into a differential error at roughly the reciprocal of that match, and the 90 dB becomes 60 dB or worse.
Two pins decide the same thing. The reference pin has to be driven from a low impedance, and the sense pin has to see the load; the vendor states that interchanging the reference and the positive input, or the negative input and the sense, degrades rejection. On a board those are adjacent pins, so a footprint error shows up as a part that works and measures badly rather than a part that fails. The check is a common mode sweep with the inputs tied together.
Buying INA132UA2K5
This is the grade to buy when the plain grade is short, because it is active in the same carrier at the same quantity and the only cost is a wider offset window. The substitution should be recorded on the build record rather than made silently, because a channel that was trimmed against the plain grade will read slightly differently after the change and a customer may see it.
The other decision is the network's load. At 80 kΩ differential a 10 kΩ source loses 11 per cent of the signal before the amplifier sees it, so a high impedance sensor needs a buffer and the difference amplifier follows it. Our drop in replacement page sets out the bench checks for a grade change, and the incoming inspection plan page covers the lot checks.
Questions that arrive with this part number
Whether the UA grade can replace the U grade is the first question, and the answer is yes with a wider offset window and a slightly wider gain error window, both of which are trimmed or budgeted rather than fundamental. Whether the reverse substitution is allowed is the second, and it usually is, because the tighter part meets the looser specification.
The third is the supply. On a single 3.3 V rail the output only reaches about 2.5 V, so a 3 V full scale signal does not fit even though the part is specified from 2.7 V. The supply minimum is a functional limit, not a signal range, and the two are often confused when a part is chosen from the first page of a sheet.