Contact Us

INA131BP

Brand: Texas Instruments
Texas Instruments INA131BP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA131BP — Power Management & Signal Chain | Superb Automation

INA131BP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA131BP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA131BP: the tight bin of the fixed gain part, 50 µV and a quarter of a microvolt per degree

The INA131BP is the tight grade of the fixed gain 100 instrumentation amplifier: 50 µV maximum initial offset and 0.25 µV per degree of drift, with a gain error of 0.024 per cent and a gain drift of 10 ppm per degree. It is the same die and the same eight pin DIP as the AP grade, selected and trimmed to a narrower window, and it is the grade a calibrated bridge or RTD channel needs when the calibration is done once and the instrument then runs for years.

Everything else follows the family: 2 nA of bias current, 12 nV per root hertz of noise, 110 dB of common mode rejection, 70 kHz of bandwidth at the fixed gain, 0.7 V per microsecond of slew, 100 microseconds of settling and 3 mA of supply current over a plus or minus 2.25 V to plus or minus 18 V window.

The INA131BP rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, fixed gain of 100
Vendor statusActive, production
Data sheetSBOS016, Burr-Brown PDS-1144E, March 1998
GradeBP, 50 µV maximum offset and 0.25 µV per degree drift
Gain100 V/V, trimmed on the die
Gain error0.024 per cent maximum
Gain drift10 ppm per degree maximum
Gain nonlinearity0.002 per cent of full scale
Input offset voltage50 µV maximum initial
Offset drift0.25 µV per degree maximum
Input bias current2 nA maximum
Voltage noise12 nV per root hertz at 1 kHz
Common mode rejection110 dB minimum
Bandwidth70 kHz at a gain of 100
Slew rate0.7 V per microsecond
Settling100 µs to 0.01 per cent
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current2.2 mA typical, 3 mA maximum
Body8 pin plastic DIP, drawing 006
Temperature rangeMinus 40 to plus 85 degrees

50 microvolts on the BP and 125 on the AP

The two grades in this family are INA131BP AP and BP, and the difference is the offset window. The BP row is 50 microvolts maximum initial offset with 0.25 microvolts per degree of drift; the AP row is 125 microvolts maximum with 1 microvolt per degree. Both are laser trimmed at wafer level, both share the 2 nA bias current and the 12 nanovolts per root hertz of voltage noise, and both are specified over minus 40 to plus 85 degrees.

At a gain of 100 an input offset of 50 microvolts is 5 millivolts at the output, which against a 2 V output span is a quarter of a per cent and can be trimmed once in production. The drift is the part that cannot be trimmed: 0.25 microvolts per degree over a 45 degree swing is 11 microvolts at the input, a fifth of the initial offset, while the AP row moves 45 microvolts over the same swing. On a channel calibrated at 25 degrees and used at 70, the grade decides the error.

A gain of 100 fixed inside the package

The INA131 has no gain resistor pin. The three op amp network and the resistors that set the gain are trimmed on the die to a fixed 100 V/V, and the eight pin body carries only the two inputs, the two supplies, the reference and the output. That removes the external resistor, its tolerance, its temperature coefficient and the resistance of the path to it, which at a gain of 100 is worth more than a tenth of a per cent on its own. It also means the gain cannot be moved: a channel that needs 50 or 200 is a different part.

The trimmed ratio is quoted as a gain error of 0.024 per cent maximum on INA131BP in the BP grade and 0.1 per cent in the AP grade, with a gain drift of 10 and 20 ppm per degree. Nonlinearity is 0.002 per cent of full scale on the BP row. On a 10 mV bridge those numbers are far below the offset and the noise, so the fixed gain is not what limits a bridge channel; on a channel that is calibrated against a reference the 0.024 per cent is the number that decides whether the calibration holds across temperature.

The eight pin DIP only, 100 degrees per watt to the board

INA131BP is available in one body, the eight pin plastic DIP with drawing 006, and there is no surface mount row in the current addendum. That decides the assembly route: through hole, wave or selective solder, and a board that is otherwise all SMD needs a mixed process for one part. The junction to ambient figure is 100 degrees per watt, so 3 mA at 15 V per rail, about 90 milliwatts, raises the junction 9 degrees above ambient, which is comfortable.

The output swings to within 1.3 V of each rail at 5 mA, so on a plus or minus 15 V supply the usable span is plus or minus 13.7 V, and a 1000 pF load is stable. Short circuit current is plus 20 and minus 15 mA, which is enough to hold a cable but not to drive a speaker. Common mode rejection is 110 dB minimum on the BP grade and 106 on the AP grade, measured with a 1 kohm source imbalance at plus or minus 10 V.

3 mA of supply current and the plus or minus 2.25 V to 18 V window

At 2.2 mA typical and 3 mA maximum, INA131BP draws four times what the INA128 family draws, and that is the price of the wider bandwidth and the fixed gain network. It is a loop powered transmitter part only at the top of the current budget; on a 4 to 20 mA loop with 3.5 mA allocated to the electronics it fits with little left over for a reference. On a rack instrument with a plus or minus 15 V supply it is irrelevant.

The supply window runs from plus or minus 2.25 V to plus or minus 18 V, so the part runs from a single 5 V rail as long as the reference sits mid rail, and from a plus or minus 15 V rail without a regulator. The absolute maximum is 18 V per rail, which means a 15 V rail with a 10 per cent transient is already at the limit, and a supply that can ring above 18 V needs a clamp rather than a hope. Power supply rejection is 3 microvolts per volt maximum on the BP grade.

40 V of input protection and a 2 nA bias current

The inputs on INA131BP survive 40 volts beyond either rail without damage, and the protection is internal, so a transducer plugged in while the rack is live does not take the amplifier with it. The safe input voltage row is quoted as plus or minus 40 V with the source at zero ohms, which is the worst case for the internal clamp current and the number to size the external resistor against.

Bias current is 2 nA maximum at 25 degrees, rising with temperature at about 8 picoamps per degree, and it flows in the source impedance. A 10 kohm bridge impedance and 2 nA is 20 microvolts of offset, which is a fifth of the input offset and worth knowing before blaming the part. A 1 kohm source keeps that error at 2 microvolts. The bias current return path has to exist: on a floating source such as a thermocouple, a DC path to the reference is required or the input sits at whatever leakage allows.

70 kHz at a gain of 100 and 0.7 V per microsecond

Fixed gain means a fixed bandwidth: INA131BP is quoted at 70 kHz for a 3 dB point at a gain of 100, with a slew rate of 0.7 volts per microsecond and a settling time of 100 microseconds to 0.01 per cent. The slew rate, not the small signal bandwidth, sets the large signal behaviour, and 0.7 volts per microsecond means a 10 V step takes 14 microseconds before settling even starts.

For a multiplexed front end the 100 microsecond settling figure is the scan budget: sixteen channels at that rate is 1.6 milliseconds per scan, or about 600 scans per second, with nothing left for the converter. That is still fast enough for a temperature or pressure logger and too slow for a vibration channel. Overload recovery from a 50 per cent overdrive is 20 microseconds, which matters when a multiplexer switches from an open channel to a live one.

Buying INA131BP

The BP grade is bought when the drift matters, and the arithmetic is simple: 0.25 against 1 µV per degree over the 45 degrees between a 25 degree calibration and a 70 degree cabinet is 11 against 45 µV at the input, which at a gain of 100 is 1.1 against 4.5 mV at the output. On a 2 V full scale that is 0.055 against 0.22 per cent, and the second number is visible on a chart recorder.

Because the part is a DIP with no reel row, the quantity question is a tube and a socket question rather than a reel question. Our last time buy page is relevant for any product that has been in production long enough to be on a through hole part, and the drop in replacement page covers the bench checks before a substitute DIP is approved.

Questions that arrive with this part number

Whether the BP and the AP are the same silicon is the first question, and they are, with the offset and drift windows as the difference. Whether the AP can ship where the BP was ordered is the second, and it can only if the drift budget has room, because the offset difference is trimmed at test and the drift difference is not.

The third is the fixed gain of 100 against a channel that needs a different gain. There is no gain pin and no external resistor, so a channel that needs 10 or 200 is a different part, and a board that was laid out for a gain resistor has to be reworked rather than reprogrammed. That is the one inflexibility of this family and it is worth stating on the drawing.